User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 69
Following constraints apply for Radius Profile configuration:
1. Message Response Time should always be less than WORP Registration Timeout parameter value.
2. If Max Retransmissions is configured as Zero, retransmissions do not occur.
3. The value of Max Retransmissions multiplied by Message Response Time should be less than WORP
Registration Timeout value.
4. Max Retransmission Valid Range is 0 to 3.
5. Message Response Time Valid Range is 3 to 9.
NOTE: RADIUS authentication configuration is applicable only for End Point A.
4.5.3 Configuring the MAC ACL (End Point A Only)
You can control the access to the network using MAC Access Control List (ACL). MAC ACL is available only on End Point A.
MAC Authentication is supported on the wireless interface only (not supported for the devices on the Ethernet side) and only
End Point B wireless MAC addresses should be added to the list. The MAC ACL is referred to only when it is enabled on the
WORP Configuration page.
To configure the MAC ACL
1. Click ADVANCED CONFIGURATION > Security > MAC ACL. The MAC Access Control screen is displayed as shown
below.
Parameter Description
Profile Name Specifies the profile name.
Max Retransmissions Specifies the maximum retransmissions allowed.
Message Response Time Specifies the message response time.
Re Authentication Period Specifies the Re Authentication Period.
Entry status Displays the Radius profile as Enable.
Server Type This is a read only parameter and displays the server type. Two
Server Types are supported: Primary Auth Server and
Secondary Auth Server.
IP Address Enter the Server’s IP address.
Server Port Specifies the port number which is used by the unit and the Radius
server to communicate. By default, RADIUS Authentication
Server communicates on port 1812.
Shared Secret Specifies the password shared by the RADIUS server and the
QB-8100 device. The default password is public.
Entry Status Select Enable/Disable to enable or disable the RADIUS server
status.