User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 64
Table 4-1 Data Rates to Rate Index Mapping Table
Table 4-2 DDRS Minimum Required SNR Table
When DDRS Status is enabled, the DDRS Status field is displayed and WORP Tx Rate is disabled in BASIC
CONFIGURATION Screen. See Basic Configuration Information for more details. Also when enabled, the DDRS Status field
is displayed and WORP Tx Rate is also disabled in ADVANCED CONFIGURATION > Wireless > Interface 1 > WORP
screen. See Configuring WORP Properties in End Point A Mode for more information.
Rate
Index
Data Rates (Mbps)
5 MHz Channel
Bandwidth (for
Full GI-800ns)
10 MHz Channel
Bandwidth (for
Full GI-800ns)
20 MHz Channel
Bandwidth (for
Full GI-800ns)
40 MHz Channel Bandwidth
Longer
Range
Higher
Through
put
Longer
Range
Higher
Through
put
Longer
Range
Higher
Through
put
Short GI-400ns Full GI-800ns
Longer
Range
Higher
Through
put
Longer
Range
Higher
Though
put
1 1.6 3.3 3.3 6.5 6.5 13 15 30 13.5 27
2 3.3 6.5 6.5 13 13 26 30 60 27 54
3 4.9 9.7 9.7 19.5 19.5 39 45 90 40.5 81
4 6.5 13 13 26 26 52 60 120 54 108
5 9.7 19.5 19.5 39 39 78 90 180 81 162
61326265252104120240108216
7 14.6 29.3 29.3 58.5 58.5 117 135 270 121.5 243
8 16.2 32.5 32.5 65 65 130 150 300 135 270
Rate Index Legacy Mode Enabled
Minimum Required SNR (dB)
Single Stream Dual Stream
17 9
210 13
313 16
416 19
520 25
625 28
728 31
831 34