User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 50
NOTE: Modifying any of End Point A parameters results in temporary loss of connectivity with the End Point B.
Bandwidth Limit Type This parameter specifies the action performed when
the traffic utilization exceeds the configured
input/output limits.
Policing: When the traffic utilization reaches the
configured limit, the excess traffic will be discarded.
Shaping: When the traffic utilization reaches the
configured limit, the excess traffic will be buffered
and sent at the rate specified in the Output
Bandwidth Limit.
Security Profile Name This parameter represents the security profile
currently used. The default Security Profile Name is
WORP Security. The Security Profile contains the
authentication and encryption methods used to
secure the connection between the End Point A and
End Point B. Refer to Security Configuration.
Radius Profile Name This parameter represents the radius profile
currently used. The radius profile contains the IP
address details of the RADIUS server. Refer to
Configuring the Radius Server Profile (End Point A
Only).
MAC ACL Status This parameter is used to enable or disable the MAC
Access Control List (ACL). When enabled, the End
Point A checks the ACL to allow or deny access to
the End Point B.
This option is available only in End Point A mode.
Radius MAC ACL Status This parameter is used to enable authentication
using RADIUS server. When enabled, the End Point
A contacts the RADIUS server for authenticating the
End Point B during the registration process. This
option is available only in End Point A mode.
Parameter Description