User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 49
Auto Multi Frame Bursting Select Enable or Disable from Auto Multi Frame
Bursting drop-down box. By default, Auto Multi
Frame Bursting is enabled.
NOTE: Auto Multi Frame Bursting is enabled
only if Multi Frame Bursting is
Enabled.
When Auto Multi Frame Bursting is disabled, the
number of packets per burst will be defined as in
the QoS Service Flow class used for communication.
When this feature is enabled, End Point A will
monitor which of the active QoS SF Classed has the
highest priority, and allow only that class to use
multi-frame bursting, all the rest SF Classes to use
only single frame per burst.
Registration Time-out It specifies the maximum duration for the
registration process to complete once End Point B
starts registering with End Point A. Default time is
10 seconds.
Retry Count This parameter specifies the maximum number of
times a data message is retransmitted, over the
wireless medium, if acknowledgement is not
received. By default, this parameter is set to 3.
DDRS Status This parameter is displayed only when DDRS feature
is enabled in ADVANCED CONFIGURATION >
Wireless > Interface 1 > DDRS. For more details
refer to DDRS.
Tx Rate This parameter represents the modulation rate at
which the packet will be transmitted from the
wireless device.
NOTE: The supported transmission rates
vary based on the Channel Bandwidth,
Guard Interval, and Number of Data
Streams parameters.
Input/Output Bandwidth Limit This parameter limits the data received on the
wireless interface and transmitted to the wireless
interface. Minimum of 64 Kbps to the maximum
value specified in the License File.
Parameter Description