User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 44
NOTE: Click COMMIT and then REBOOT for the changes to take effect.
Parameter Description
Ethernet
Address Type This field is applicable only if the Network mode on the System screen is
configured in Bridge mode. This parameter specifies whether the device network
parameters are to be configured through DHCP or to be assigned statically.
Select Dynamic to configure the device as a Dynamic Host Configuration Protocol
(DHCP) client. If Dynamic is selected, the device obtains the IP settings from a
network DHCP server automatically during the bootup. If you do not have a DHCP
server or if you want to manually configure the device’s IP settings, select Static
for the Address Type.
IP Address Enter the IP Address of the interface.
In Bridge Mode: When the Address Type is selected as Dynamic, this field
becomes read-only and displays the current IP address of the device.
If the device cannot obtain an address from a DHCP server, it displays the default
IP Address as 169.254.128.132 for End Point A and 169.254.128.131 for End
Point B.
In Routing Mode: For these interfaces, this field displays the default IP Addresses
as follows:
Ethernet interface: 169.254.128.132
Wireless interface: 169.254.130.132
Subnet Mask This parameter represents the subnet mask of the interface.
In Bridge Mode: When the Address Type is selected as Dynamic, this field
becomes read-only and displays the current subnet mask of the device.
If the device cannot obtain an address from a DHCP server, it displays the default
subnet mask as 255.255.255.0.
Default Gateway IP Address
Default Gateway IP
Address
This parameter represents the gateway IP Address of the device.
In Bridge Mode: When the Address Type is selected as Dynamic, this parameter
becomes read-only and displays the device’s current gateway IP Address that is
obtained through DHCP. If the device cannot obtain an address from a DHCP
server, the default gateway IP Address is 169.254.128.132. When Static IP
assignment is used, subnet of the default gateway should match with the subnet
of any one of the interfaces.
DNS
Primary DNS Specifies the IP Address of the Primary DNS Server.
Secondary DNS Specifies the IP Address of the Secondary DNS Server.