User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Advanced Configuration
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 41
4.1 System Configuration
The System screen allows you to configure the QB-8100 device as an End Point A or an End Point B, the frequency domain,
and the network mode as Bridge or Routing.
To configure the System
1. Click ADVANCED CONFIGURATION > System. The System screen is displayed as shown below:
Figure 4-1 System screen
2. From the Radio Mode drop-down menu, select either End Point A or End Point B.
3. From the Frequency Domain drop-down menu, select a frequency domain.
4. From the Network Mode drop-down menu, select either Bridge or Routing.
5. For the Maximum MTU field, enter the maximum MTU value.
6. Click OK.
The following table lists the System parameters and their descriptions:
Parameter Description
Radio Mode Radio mode specifies the mode of operation and
QB-8100 supports two types of modes, End Point A
and End Point B.
Frequency Domain A valid frequency domain must be set before the
device can be configured with any other parameters.
Selecting a frequency domain makes the device
compliant with the allowed frequency bands and
channels for that regulatory domain.
Network Mode The device can be configured in two network modes:
Bridge Mode and Routing Mode. The default network
mode is Bridge Mode.
Refer to Configuring IP in Bridge or Router Mode for
more information.
Active Network Mode This is a read-only parameter which shows current
operating network mode of the device. It is displayed
only when the newly configured Network mode differs
from the current Active Network mode.