User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Installation and Initialization
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 28
2.4.3.1 Assigning the IP Address Manually
1. Select the IP Address Type as Static and then enter the appropriate IP Address, Subnet Mask, and the Gateway IP
Address parameters.
2. Enter the SNMP Read/Write password in the Read/Write Password field. By default, it is public.
3. Click OK to save the details.
The device automatically reboots after clicking OK.
By clicking Rescan, verify whether the changes are applied or not. Then, click Web Configuration to open the web
interface.
2.4.3.2 Assigning the IP Address Dynamically
NOTE: Before setting the IP Address Type as Dynamic, ensure there is a DHCP server in the network.
1. Select the IP Address Type as Dynamic. The IP Address, Subnet Mask and the Gateway IP Address fields get
disabled.
2. Enter the SNMP Read/Write password in the Read/Write Password field. By default, it is public.
3. Click OK to save the details.
The device automatically reboots after clicking OK. By clicking Rescan, verify whether the changes are applied or not. Then,
click Web Configuration to open the web interface.
2.5 Logging in to the Web Interface
Once the device is connected to your computer, use a web browser to configure and monitor the device. Enter
http://169.254.128.132 (the device default IP address) in the address bar.
The user is prompted to enter the username and password to access the wireless device.
The default User Name is admin and Password is public.
Figure 2-9 Login Page
NOTES:
• Depending on the settings made during the device initialization, the IP address may be either a dynamic IP address
assigned by a network DHCP server or a static IP address which is manually configured. Refer to ScanTool for
information on how to determine the device’s IP address and manually configure a new IP address.
• If the connection is slow or unable to connect, use the Internet Explorer Tools option to ensure that you are not using
a proxy server for the connection.