User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Product Series Models Description
MP-8ABC-ZZZ-YYY-XX A - Represents number of radios (1, 2)
MM-8ABC-ZZZ-YYY-XX B - Represents the operating frequency band of the first radio
C - Represents the frequency band of the second radio
Example:
0 - Dual band and connectorized
2 - 2Ghz band with integrated antenna
5 - 5Ghz band with integrated antenna
ZZZ - Represents the type of the network unit
Example:
CPE - Customer Premise Equipment
BSU - Base Station Unit
SUA - Subscriber Unit with external antenna
SUR - Subscriber Unit with Integrated antenna
EPR - End Point with Integrated antenna
EPA - End Point with external antenna
LNK - Link consisting of two End Points
YYY - Represents the bandwidth limit of the network unit and optionally a letter at the end representing the
device configuration
Example:
5, 12, 25, 50, 100 - Bandwidth limits in Mbps
100i - 100Mbps indoor unit
100c - 100Mbps unit with external antenna
100a - 100Mbps unit with Integrated Antenna
XX - Represents the regulatory domain
Example:
US - Compliant to FCC
WD - Complaint to ETSI/CE and IC
ORiNOCO®
Access Points
AP-810M-xx Indoor AP with single radio and Mesh Capability XX - Represents the regulatory domain
AP-8100M-xx Indoor AP with dual radio and Mesh Capability Example:
AP-820MR-xx Outdoor AP with single radio and Mesh Capability US - Compliant to FCC
AP-822MR-xx Outdoor AP with single radio and Mesh Capability, Integrated 2.4GHz Panel Antenna WD - Complaint to ETSI/CE and IC
AP-810MR-xx Outdoor AP with single radio and Mesh Capability
AP-812MR-xx Outdoor AP with single radio and Mesh Capability, Integrated 2.4GHz Sector Antenna
AP-8100MR-xx Outdoor AP with dual radio and Mesh Capability
Tsunami™
Point-to-
Multipoint series
QB-8ABC-ZZZ-YYY-XX
Tsunami™
QuickBridge
Point to Point
series
Model List