User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Technical Specifications
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 215
Hardware Specifications
Physical and Environmental Specifications
Security Features • Critical feature support via WORP for secure
long-range wireless deployments in
unlicensed frequency spectrum
• MD5 (embedded in WORP) authentication
between End Point A and End Point B
• MAC Authentication (Configured on End
Point A)
• Secure “over the air encryption” and
AES-CCM
• RADIUS MAC Access Control (Configured on
End Point A)
Tools • Site Survey (to be performed on End Point B)
• Link Test to determine the local/remote
signal/noise levels.
Management Interface Flexible and responsive management interfaces
through Web, CLI and SNMP. SNMPv3 support
facilitates secure management.
Category Specification
Radio 5 GHz dual stream MIMO radio
Clock Speed 333 MHz
Memory Flash: 16 MB
RAM: 128 MB
Input Power Power-over-Ethernet 48 VDC,0.40 A
Category Specification
Physical
QB-8100 Dimensions (H x W x L) 7.77 x 7.56 x 3.94 inches (197.5 x 192 x 100mm)
QB-8100 Weight 1.6 lbs (.73 kg)
Environmental
Storage Temperature -40º to 70ºC (-40º to 158º Fahrenheit)
Operating Temperature -33º to 55ºC (-40º to 131º Fahrenheit)
Humidity Max 95% relative humidity (non-condensing)
Water and Dust Proof IP65
Category Specification