User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Frequency Domains and Channels
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 203
NOTE: While choosing a 40MHz bandwidth, you can select 40 PLUS or 40 MINUS. 40 PLUS means the center
frequency calculation is to be done for 20MHz and add another 20MHz to the top edge of 20MHz. 40 MINUS means
the center frequency calculation is to be done for 20MHz and add another 20MHz to the bottom edge of 20MHz.
Details for 40MHz Bandwidth
For 40 PLUS
• 2.4GHz -> Channel 1 = 2412MHz.
• Bandwidth starts from 2403 and ends at 2442
• 5GHz -> Channel 52 = 5260
• Bandwidth starts from 5251 and ends at 5290
For 40 MINUS
• 2.4GHz -> Channel 5 = 2432MHz.
• Bandwidth starts from 2403 and ends at 2442
• 5GHz -> Channel 56 = 5280
• Bandwidth starts from 5251 and ends at 5290
India 5.8
GHz
5830 ~ 5870 Non-DFS 166(5830),
167(5835)...
173(5865),
174(5870).
166(5830),
167(5835)....
173(5865),
174(5870).
167(5835),
168(5840)...
172(5860),
173(5865).
167(5835),
168(5840),
169(5845).
171(5855),
172(5860),
173(5865).
CANADA
5.8 GHz
5735 ~ 5855 Non-DFS 147(5735),
148(5740)....
170(5850),
171(5855).
147(5735),
148(5740).....
170(5850),
171(5855).
148(5740),
149(5745)...
169(5845),
170(5850).
148(5740),
149(5745)...
165(5825),
166(5830).
152(5760),
153(5765)...
169(5845),
170(5850).
U.K
5.8 GHz
5735 ~ 5835 DFS Not
Supported
147(5735),
148(5740).....
156(5780),
157(5785),
167(5835).
147(5735),
148(5740)...
156(5780),
157(5785),
167(5835).
147(5735),
148(5740)...
153(5765),
154(5770).
151(5755),
152(5760)....
156(5780),
157(5785),
167(5835).
Frequency
Domain
Frequency
Band
(Start Center
Frequency ~
End Center
Frequency in
MHz)
DFS Allowed Channels (Center Frequency)
5 MHz
10 MHz 20 MHz 40 PLUS
MHz
40 MINUS
MHz