User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Monitoring the System
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 163
The following table lists the parameters and their descriptions:
6.4.4 RIP Database
This section shows the information about the RIP database. It contains routes (Routing Information Protocol updates) learnt
from other routers.
Field Description
In Msgs/Out Msgs The number of ICMP messages that are received/transmitted by the
device.
In Errors/Out Errors The number of ICMP messages that the entity received/transmitted but
determined as having errors.
In Dest Unreachs/
Out Dest Unreachs
The number of ICMP Destination Unreachable messages
received/transmitted.
In Time Excds/Out Time Excds The number of ICMP Time Exceeded messages received/transmitted.
In Parm Probs/Out Parm Probs The number of ICMP Parameter Problem messages received/transmitted.
In Srec Quenchs/Out Srec Quenchs The number of ICMP Source Quench messages received/transmitted.
In Redirects/Out Redirects The rate of ICMP Redirect messages received/transmitted.
In Echos The rate of ICMP Echo messages received.
NOTE: Out Echos parameter is not displayed in the ICMP
statistics list.
In EchoReps/Out EchoReps The rate of ICMP Echo Reply messages received/transmitted.
In Timestamps/Out Timestamps The rate of ICMP Timestamp (request) messages received/transmitted.
In Timestamps Reps/
Out Timestamps Reps
The rate of ICMP Timestamp Reply messages received/transmitted.
In Addr Masks/Out Addr Masks The number of ICMP Address Mask Request messages
received/transmitted.
In Addr Mask Reps/ Out Addr Mask
Reps
The number of ICMP Address Mask Reply messages
received/transmitted.