User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Monitoring the System
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 159
6.3.2 Learn Table
Learn Table is used to view all MAC addresses the device has learnt on an interface. The Learn Table displays the information
of learnt MAC addresses, the interface on which it learnt the MAC address, aging timer corresponding to the MAC add entry,
and the type of interface as local interface or attached interface to the device. It reports the MAC address for each node that
the device has learnt on the network and the interface on which the node was detected. There can be up to 10,000 entries in
the Learn Table.
To view the Learn Table entries,
1. Click MONITOR > Bridge > Learn Table.
In Unicast Packets Displays the number of subnetwork unicast packets
received at the bridge interface.
In Non-unicast Packets Displays the number of non-unicast (i.e.,
subnetwork-broadcast or subnetwork-multicast)
packets received at the bridge interface.
In Errors Displays the number of inbound packets that
contained errors and are restricted for delivering them
to a higher-layer protocol at the bridge interface.
Out Octets Displays the total number of octets transmitted out of
the interface, including the framing characters.
Out Unicast Packets Displays the total number of packets requested by
higher-level protocols to be transmitted out of the
interface to a subnetwork-unicast address, including
those that were discarded or not sent.
Out Discards Displays the number of error-free outbound packets
chosen to be discarded to prevent them being
transmitted. One possible reason for discarding such a
packet could be to free up buffer space.
Out Errors Displays the number of outbound packets that could
not be transmitted because of errors.
Parameter Description