User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Monitoring the System
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 154
NOTE: For better results, the Send Failure/Send Retrieve must be low in comparison to Send Success. The same applies
for Receive Retries/Receive Failure. Click Refresh to update the details in this page.
6.2.2 End Point B Link Statistics (End Point A only)
WORP End Point B Link Statistics provides the information related to the End Point B currently connected to the End Point A.
This operation is available only in End Point A mode operations.
To view the Interface Statistics, click MONITOR > WORP Statistics > Interface 1 > End Point B Link Statistics.
Request For Service Refers to the number of requests for service messages
sent (End Point B) or received (End Point A).
Registration Requests Refers to the number of registration request messages
sent (End Point B) or received (End Point A) on WORP
interface.
Registration Rejects Refers to the number of registration reject messages
sent (End Point A) or received (End Point B) on WORP
interface.
Authentication Requests Refers to the number of authentication request
messages sent (End Point B) or received (End Point A)
on WORP interface.
Authentication Confirms Refers to the number of authentication confirm
messages sent (End Point A) or received (End Point B)
on WORP interface.
Registration Attempts Refers to the number of times a Registration Attempt
has been initiated.
Registration Incompletes Refers to the number of registration attempts that is
not completed yet.
Registration Timeouts Refers to the number of times the registration
procedure timed out.
Registration Last Reason Refers to the reason for why the last registration was
aborted or failed.
Field Description