User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Monitoring the System
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 153
Avg Remote Noise Refers to the noise level with which the End Point B
receives wireless frames from the End Point A.
WORP Data Messages Specifies the sent or received data frames through
wireless interface.
Poll Data Refers to the number of polls with data messages sent
(End Point A) or received (End Point B).
Poll No Data Refers to the number of polls with no data messages
sent (End Point A) or received (End Point B).
Reply Data Refers to the number of poll replies with data
messages sent (End Point B) or received (End Point A).
Reply More Data Refers to the number of poll replies with more data
messages sent (End Point B) or received (End Point A).
Reply No Data Refers to the number of poll replies with no data
messages sent (End Point B) or received (End Point A).
Poll No Replies Refers to the number of times poll messages were sent
but no reply was received. This parameter is valid only
on End Point A.
Data Transmission Statistics Specifies the number of transmissions occurred
through the interface.
Send Success Refers to the number of data messages sent and
acknowledged by the peer successfully.
Send Retries Refers to the number of data messages that are
re-transmitted and acknowledged by the peer
successfully.
Send Failures Refers to the number of data messages that requires
re-transmission. These frames are not acknowledged
by the peer.
Receive Success Refers to the number of data messages received and
acknowledged successfully.
Receive Retries Refers to the number of successfully received
re-transmitted data messages.
Receive Failures Refers to the number of data messages that were not
received successfully.
Registration details Specifies the status of the entire registration process.
Remote Partners Refers to the number of remote partners. For an End
Point B, this parameter is always zero or one.
Announcements Refers to the number of Announcement messages sent
(End Point A) or received (End Point B) on WORP
interface.
Field Description