User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
System Management
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 136
5.3 Services: Configuring the Passwords
SNMP version, SNMP passwords, and SNMP Trap Host Table parameters can be configured to prevent unauthorized access.
Each management interface can be configured with its own password. Each of the three management interfaces
(HTTP/HTTPS, Telnet/SSH, and SNMP) is arranged in tabs under the Services link of MANAGEMENT tab in the Main Left
Panel.
The following special characters are not allowed for setting passwords for Telnet/SSH, HTTP/HTTPS, and SNMP v2/v3: - / \ ' "
= ? and blank space.
NOTE: The passwords in the Services screen are configurable.
5.3.1 HTTP/HTTPS
Figure 5-11 HTTP/HTTPS
The parameters for HTTP/HTTPS are described in the following table.
Parameter Description
Password Set a new password for the interface or interfaces (Ethernet/
Wireless) to manage the device through the Web interface. Enter
a password between 6 and 32 characters in the Password field.
The default password is “public”.
HTTP Select Enable to allow HTTP access to the device from any host.
You can also select Disable to prevent access to the device from
Web interface. Similar settings are applicable for Hypertext
Transfer Protocol over Secure Socket Layer or HTTPS.
HTTP Port Specifies the port number for HTTP interface. By default, the port
number is 80.