User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
System Management
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 133
To upgrade the firmware via TFTP server:
1. Enter the TFTP Server IP Address.
2. Enter the name of the firmware file to update to the device.
3. Click Update to initiate the new firmware updation or click Update and Reboot to update and reboot with new
firmware immediately.
5.2.4 Upgrade Configuration via TFTP
For upgrading the configuration via TFTP Server, click MANAGEMENT > File Management > Upgrade Configuration >
TFTP.
To upgrade the binary configuration file via TFTP server
1. Select the Binary Config option button.
1. Enter the TFTP Server IP Address.
2. Enter the name of the configuration file to be updated to the device.
Click Update to initiate the TFTP update operation or click Update and Reboot to update and reboot with new
configuration immediately.
Figure 5-7 Upgrade Binary Configuration via TFTP
To upgrade the Text Based Configuration file via TFTP server
1. Select the Text Based Config option button. For more information on Text Based configuration file refer to Text
Based Configuration (TBC) File Management.
2. Enter the TFTP Server IP Address.
3. Enter the name of the configuration file to be updated to the device.
• Click Update to initiate the TFTP update operation. Then click Load to apply the updated changes. Finally click
COMMIT for the changes to take effect.
Or
• Click Update & Load to update and load with new configurations immediately and then Click COMMIT for the
changes to take effect.