User's Manual
Table Of Contents
- Preface
- Overview
- Installation and Initialization
- Basic Configuration
- Advanced Configuration
- 4.1 System Configuration
- 4.2 Network Configuration
- 4.3 Ethernet Properties Configuration
- 4.4 Wireless Configuration
- 4.5 Security Configuration
- 4.6 Quality of Service (QoS) Configuration
- 4.7 VLAN Configuration (Bridge Mode only)
- 4.8 Filtering Configuration (Bridge Only)
- 4.9 DHCP Configuration
- 4.10 IGMP Snooping (Bridge Mode only)
- 4.11 Routing Features Configuration
- System Management
- Monitoring the System
- Procedures
- 7.1 TFTP Server Setup
- 7.2 Web Interface Firmware Download
- 7.3 Configuration Backup
- 7.4 Configuration Restore
- 7.5 Text Based Configuration (TBC) File Management
- 7.6 Soft Reset to Factory Default
- 7.7 Hard Reset to Factory Default
- 7.8 Forced Reload
- 7.9 Upgrade a New Firmware Using ScanTool in Bootloader Mode
- 7.10 Download a New Firmware Using CLI from Bootloader
- Troubleshooting
- 8.1 PoE Injector
- 8.2 Connectivity Issues
- 8.3 Communication Issues
- 8.4 Setup and Configuration Issues
- 8.4.1 Lost Password
- 8.4.2 The QB-8100 Responds Slowly
- 8.4.3 Device Has Incorrect IP Address
- 8.4.4 HTTP Interface Does Not Work
- 8.4.5 Telnet CLI Does Not Work
- 8.4.6 TFTP Server Does Not Work
- 8.4.7 Setting IP Address using Serial Port
- 8.4.8 RADIUS Authentication Server
- 8.4.9 TFTP Server
- 8.4.10 Recovery Procedures
- 8.4.11 Soft Reset to Factory Defaults
- 8.4.12 Hard Reset to Factory Defaults
- 8.4.13 Forced Reload
- 8.4.14 VLAN Operation Issues
- 8.4.15 Changes Do Not Take Effect
- 8.4.16 Link Problems
- 8.4.17 General Check
- 8.4.18 Statistics Check
- 8.4.19 Analyzing the Spectrum
- Frequency Domains and Channels
- Boot Loader CLI and ScanTool
- Technical Specifications
- Part Numbers
- Regulatory Approval and Frequency Domains
- Integrated Dual Polarized Panel Antenna Specifications
- Radio and Transmission Specifications
- OFDM Modulation Rates
- Wireless Protocol
- Interfaces
- Transmit Power Settings
- Receive Sensitivity
- Latency
- Latency
- Management
- Power Supply
- LEDs
- Software Features
- Hardware Specifications
- Physical and Environmental Specifications
- MTBF and Warranty
- Lightning Protection
- Statement of Warranty
- Technical Services and Support
Overview
Tsunami QB-8100 Series (100 Mbps/5 Mbps Models) Installation and Management Guide 11
1.1 Introduction
The Tsunami QuickBridge 8100 is a wireless point-to-point device designed to provide wireless networking solutions for
enterprises and small business markets. Two pre-configured bridges enable users to easily, quickly, and economically install a
wireless extension between two locations, eliminating the need for costly leased line or cable alternatives.
The product’s primary components are a wireless device and a Power-over-Ethernet injector. The wireless device, which is
encased in an outdoor rated weatherproof container, has an integrated antenna or external antenna connectors and can be
mounted to the side of a building, on a pole, or on a tower structure.
Power and Ethernet connections must be supplied through a UV-protected CAT5 cable (not supplied) attached to a
Power-over-Ethernet (PoE) injector. The PoE injector should be located either in an outdoor rated weatherproof enclosure
located near the device or inside a building. The device can then be connected to a switch or hub on your network or directly
to a PC.
Some of the key features of the QuickBridge 8100 series include:
• High power 2x2 MIMO radio
• Highly optimized WORP (Wireless Outdoor Routing Protocol) for outdoor applications
• Asymmetric bandwidth management
• Management through a Web Interface, a Command Line Interface (CLI), or Simple Network Management Protocol
(SNMP)
• Software and configuration upgrade through HTTP/TFTP file transfer
• Outdoor placement for significantly improved range and ease of installation
• 5 GHz 2x2 MIMO integrated antenna versions for flexible deployment
• VLAN Support
• QoS based on IEEE 802.16e