User's Manual
Table Of Contents
- Introduction
- Installation and Initialization
- Hardware Description
- System Requirements
- Product Package
- Hardware Installation
- Step 1: Choose a Location
- Step 2: Unpack Shipping Box
- Step 3: Assemble the Cable
- Step 4: Determine Proper Mounting Orientation
- Step 5: Assemble Mounting Hardware
- Step 6: Mount the Unit
- Step 7: Plug in the Cables
- Step 8: Power on the Unit
- Step 9: View LEDs
- Step 10: Align the Antenna
- Step 11: Tighten the Cables
- Step 12: Weatherproof the Connectors
- Step 13: Install Documentation and Software
- Using the Web Interface
- Installing Latest Software
- First Configuration
- Base Station Configuration
- Introduction
- System Configuration
- MAC Configuration
- Radio Configuration
- Radio Downlink Burst Profile Configuration
- Radio Uplink Burst Profile Configuration
- Networking Configuration
- Global Positioning System (GPS)
- Subscriber Station Authentication
- Subscriber Station List
- Service Class Creation
- Logging Configuration
- Management Interface Configuration
- Subscriber Station Configuration
- Commands on BS/SS
- Log Messages on the BS/SS
- Monitoring the BS and SS
- Technical Specifications
- Command Line Interface
- CLI Overview
- Configuration from the Base Station
- Configuration from the Subscriber Station
- Monitoring the BS and SS
- Technical Services and Support
- Statement of Warranty
Base Station Configuration Tsunami MP.16 3650 System User Guide
Service Class Creation
90
– Unsolicited Grant Service (UGS): This mechanism is defined by the following QoS parameters: maximum
sustained data rate, maximum latency, and tolerable jitter. See below.
• Service Flow Direction: Select Uplink or Downlink.
• QoS Parameters
– Maximum Sustained Data Rate: The peak information rate of the service flow. All traffic classified onto a
service flow in excess of this rate is dropped. Set this parameter to unlimited, or to any value between 8 kbps
and 8192 kbps. The default value is unlimited. Set to 0 for unlimited.
– Minimum Reserved Traffic Rate: The minimum reserved traffic rate for the service flow. Set this parameter to
any value between 8 kbps and 8192 kbps. The default value is 0 (unlimited).
– Maximum Latency: The maximum latency between the reception of a packet by the BS or SS on its network
interface and the forwarding of the packet to the RF interface. Set this parameter to any value between 5 ms
and 100 ms, in increments of 5 ms.
– Tolerable Jitter: The maximum delay variation for the connection. Set this parameter to any value between 5
ms and 100 ms, in increments of 5 ms.
– Traffic Priority: The priority assigned to the service flow. Set this parameter to any value between 0 and 7,
where 7 is the highest priority.
5. Click OK.
Pre-Defined Service Flow Classes
The MP.16 system comes with several pre-defined service flow classes that can be used as is, edited, or used as
templates for the creation of new SF classes. These pre-defined classes can be deleted by the administrator; if they are
deleted, they are restored if the system is reset to factory defaults.
The following table describes the pre-defined service flow classes.
Subscriber Station Class Creation
You can create, delete, and edit up to 64 SS classes, including those that are predefined (see Pre-Defined Subscriber
Station Classes). To do so, you will use the SFs and PIRs created the previous sections.
1. Click Service Class Creation > SS Class
Table 3-4 Pre-Defined Service Flow Classes
Service Flow Class Name Scheduling Type Direction Max.
Sustained
Data Rate
Min.
Reserved
Traffic Rate
Max.
Latency
Tolerable
Jitter
Traffic
Priority
UL-Unlimited BE Best Effort Uplink Unlimited 0 — — —
DL-Unlimited BE Best Effort Downlink Unlimited 0 — — —
UL-G711 20ms VoIP UGS Unlimited Grant
Service
Uplink 100 kbps — 20 ms 0 —
DL-G711 20ms VoIP UGS Unlimited Grant
Service
Downlink 100 kbps — 20 ms 0 —