User's Manual
Table Of Contents
- Introduction
- Installation and Initialization
- Hardware Description
- System Requirements
- Product Package
- Hardware Installation
- Step 1: Choose a Location
- Step 2: Unpack Shipping Box
- Step 3: Assemble the Cable
- Step 4: Determine Proper Mounting Orientation
- Step 5: Assemble Mounting Hardware
- Step 6: Mount the Unit
- Step 7: Plug in the Cables
- Step 8: Power on the Unit
- Step 9: View LEDs
- Step 10: Align the Antenna
- Step 11: Tighten the Cables
- Step 12: Weatherproof the Connectors
- Step 13: Install Documentation and Software
- Using the Web Interface
- Installing Latest Software
- First Configuration
- Base Station Configuration
- Introduction
- System Configuration
- MAC Configuration
- Radio Configuration
- Radio Downlink Burst Profile Configuration
- Radio Uplink Burst Profile Configuration
- Networking Configuration
- Global Positioning System (GPS)
- Subscriber Station Authentication
- Subscriber Station List
- Service Class Creation
- Logging Configuration
- Management Interface Configuration
- Subscriber Station Configuration
- Commands on BS/SS
- Log Messages on the BS/SS
- Monitoring the BS and SS
- Technical Specifications
- Command Line Interface
- CLI Overview
- Configuration from the Base Station
- Configuration from the Subscriber Station
- Monitoring the BS and SS
- Technical Services and Support
- Statement of Warranty
Command Line Interface Tsunami MP.16 3650 System User Guide
Configuration from the Base Station: Service Class Creation
147
MP16(SSCLASS1)>set vlanmode transparent
No further parameters need to be set.
Option B: Configuring SS Class for Access Mode
If the BS VLAN mode is set to Transparent, you can set the VLAN mode of the SS Class to Access to restrict access to
the network. When you select Access, you must also select a VLAN ID with management access and set the
management priority. The Management VLAN ID must be taken from the VLAN ID List configured from the root prompt or
from the Configuration > Networking > VLAN ID List page in the Web interface.
MP16(SSCLASS1)>set vlanmode access vlanid 25 priority 1
Above, you selected VLAN ID 25 as the Management VLAN ID for the SS Class, and you set the Management Priority to
1.
Option C: Configuring SS Class for Trunk Mode
If the BS VLAN mode is set to Trunk, you can set the VLAN mode of the SS Class Trunk to allow access by multiple
VLANs. When you select Trunk, you must also select a VLAN ID for management access.
MP16(SSCLASS1)>set vlanmode trunk vlanid 1
With the VLAN mode to Trunk, you can add up to 16 entries to the list of allowed VLAN IDs. The VLAN IDs must be taken
from the VLAN ID List configured from the root prompt or from the Configuration > Networking > VLAN ID List page in
the Web UI.
MP16(SSCLASS1)>add vlanid 15
MP16(SSCLASS1)>add vlanid 25
MP16(SSCLASS1)>add vlanid 100
Above, you selected VLAN ID 1 as the Management VLAN ID, and added VLAN IDs 15, 25, and 100 to the list of allowed
VLAN IDs.
Option D: Configuring SS Class for Mixed Mode
If the BS VLAN mode is set to Trunk, you can set the VLAN mode of the SS Class to Mixed to allow both tagged and
untagged frames to access the network. When you select Mixed mode, you must also specify a VLAN Access ID and a
VLAN Trunk ID to be used for management, as well as an Access priority.
MP16(SSCLASS1)>set vlanmode access accessid 1 access priority 7 trunkid 12
With the VLAN mode to Mixed, you can add up to 16 entries to the list of allowed VLAN IDs. The VLAN IDs must be taken
from the VLAN ID List configured from the root prompt or from the Configuration > Networking > VLAN ID List page in
the Web UI.
MP16(SSCLASS1)>add vlanid 15
MP16(SSCLASS1)>add vlanid 25
MP16(SSCLASS1)>add vlanid 100
Above, you selected VLAN ID 1 as the Access Management VLAN ID and VLAN ID 12 as the Trunk Management VLAN
ID. You then added VLAN IDs 15, 25, and 100 to the list of allowed VLAN IDs.
Step 5: View SS Class Configuration
In this step, you will review the SS Class configuration you just completed:
MP16(SSCLASS1)>show