User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Troubleshooting
90
System Alarms (Traps)
Security Alarms
Wireless Interface Card Alarms
Operational Alarms
FLASH Memory Alarms
TFTP Alarms
Image Alarms
Standard MIB-II (RFC 1213) Alarms
Bridge MIB (RFC 1493) Alarms
oriTrapAuthenticationFailure A client has failed to authenticate using one of the following
authentication methods: MAC Access Control Table, RADIUS
MAC Authentication, or 802.1x Authentication (for 802.1x, EAP
type is specified)
oriTrapUnauthorizedManagerDetected An unauthorized manager has attempted to view and/or modify
parameters
oriTrapWLCNotPresent Wireless radio not present
oriTrapWLCFailure Wireless radio general failure
riTrapWLCRemoval Wireless radio removal
oriTrapWLCIncompatibleFirmware Wireless radio incompatible firmware detected
oriTrapWLCVoltageDiscrepancy Wireless radio voltage discrepancy detected
oriTrapWLCIncompatibleVendor Wireless radio incompatible vendor detected
oriTrapWLCFirmwareDownloadFailure Wireless radio firmware download failure detected
oriTrapWatchDogTimerExpired Watch Dog Timer has expired
oriTrapRADIUSServerNotResponding RADIUS Server is not responding or error communicating with RADIUS Server
oriTrapModuleNotInitialized Module has not been initialized
oriTrapDeviceRebooting Device is rebooting
oriTrapTaskSuspended Task suspension has been detected
oriTrapBootPFailed BootP failure detected (no response from BootP Server)
oriTrapDHCPFailed DHCP Client failure detected (no response from DHCP server)
oriTrapFlashMemoryEmpty Flash memory empty
oriTrapFlashMemoryCorrupted Flash memory data corrupted
oriTrapTFTPFailedOperation TFTP (upload or download) failure detected
oriTrapTFTPOperationInitiated TFTP (upload or download) operation initiated
oriTrapTFTPOperationCompleted TFTP (upload or download) operation completed
oriTrapZeroSizeImage Zero size image has been downloaded to device
oriTrapInvalidImage Invalid image has been downloaded to device
oriTrapImageTooLarge Image downloaded to device is too big
oriTrapIncompatibleImage Incompatible image has been downloaded to device
coldStart Device has been turned on or rebooted
linkUp Device Link is up (Ethernet interface is up)
linkDown Device Link is down (Ethernet interface is down)
newRoot New root has been added to Bridge
topologyChange Network Topology change has been detected