User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Advanced Configuration
39
• Gateway IP Address: The AP-600 will assign the specified address to its DHCP clients.
• Primary DNS IP Address: The AP-600 will assign the specified address to its DHCP clients.
• Secondary DNS IP Address: The AP-600 will assign the specified address to its DHCP clients.
• Number of IP Pool Table Entries: This is a read-only field that reports the number of IP address pools currently
configured.
• IP Pool Table Entry: This entry specifies a range of IP addresses that the AP can assign to its wireless clients.
Click Add to create a new entry. Click Edit to change an existing entry. Each entry contains the following field:
–Start IP Address
– End IP Address
– Default Lease Time (optional): The default time value for clients to retain the assigned IP address. DHCP
automatically renews IP Addresses without client notification. This parameter supports a range between 0 and
86400 seconds. The default is 86400 seconds.
– Maximum Lease Time (optional): The maximum time value for clients to retain the assigned IP address.
DHCP automatically renews IP Addresses without client notification. This parameter supports a range
between 0 and 86400 seconds. The default is 86400 seconds.
– Comment (optional)
– Status: IP Pools are enabled upon entry in the table. You can also disable or delete entries by changing this
field’s value.
127(
127(127(
127(
You must reboot the Access Point before changes to any of these DHCP server parameters take effect.
Link Integrity
The Link Integrity feature checks the link between the AP-600 and the nodes on the Ethernet backbone. These nodes
are listed by IP address in the Link Integrity IP Address Table. The AP-600 periodically pings the nodes listed within the
table. If the AP-600 loses network connectivity (that is, the ping attempts fail), the AP-600 disables its wireless
interface until the connection is restored. This forces the unit’s wireless clients to switch to another Access Point that
still has a network connection. Note that this feature does not affect WDS links (if applicable).
Figure 4-4 Link Integrity Configuration Screen