User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Introduction
16
The following table provides detailed information on the some of the differences between the 802.11a and 802.11b
feature sets.
AP-600a
(802.11a)
AP-600b
(802.11b)
Physical Layer Type
(Modulation Type)
ODFM
(Orthogonal Frequency Division Multiplexing)
DSSS
(Direct Sequence Spread Spectrum)
Auto Channel Select Enable (default)
Disable
Note: A user cannot manually select a
channel for products sold in Europe; these
products require automatic channel selection
using DFS. See Dynamic Frequency
Selection (DFS).
Enable (default)
Disable
Frequency Channel Available Channels vary by regulatory domain
and/or country. See 802.11a Channel
Frequencies for the AP-600a for details.
Available Channels vary by regulatory domain
and/or country. See 802.11b Channel
Frequencies for the AP-600b for details.
Transmit Rate 0 - Auto Fallback (default)
6 Mbits/sec
9 Mbits/sec
12 Mbits/sec
18 Mbits/sec
24 Mbits/sec
36 Mbits/sec
48 Mbits/sec
54 Mbits/sec
For 2X Turbo mode (not available in all
countries):
0 - Auto Fallback (default)
12 Mbits/sec
18 Mbits/sec
24 Mbits/sec
36 Mbits/sec
48 Mbits/sec
72 Mbits/sec
96 Mbits/sec
108 Mbits/sec
N/A
Distance Between APs N/A Large (default)
Medium
Small
Minicell
Microcell
Multicast Rate N/A 1 Mbits/sec
2 Mbits/sec
5.5 Mbits/sec
11 Mbits/sec
Available options depend on Distance
Between APs setting
Interference Robustness N/A Enable (default)
Disable
Closed System N/A Enable
Disable (default)
Load Balancing N/A Enable (default)
Disable
Medium Density Distribution N/A Enable (default)
Disable