User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Introduction
15
Software Features
The table below compares the software features available for the AP-600a and the AP-600b:
*This feature is not available if you are using an ORiNOCO 802.11a/b ComboCard or a non-ORiNOCO client with the AP-600b.
Feature AP-600a
802.11a
AP-600b
802.11b
Comments
Number of stations per Basic Service Set (BSS) up to 50 up to 250
HTTP Server Yes Yes
Telnet / CLI Yes Yes
SNMP Agent Yes Yes
Emergency Reset to Default Configuration Yes Yes
DHCP Client Yes Yes
DHCP Server Yes Yes
TFTP Yes Yes
RADIUS Access Control Yes Yes
Fallback to Primary RADIUS Server Yes Yes
RADIUS Session Timeout Yes Yes
RADIUS Multiple MAC Address Formats Yes Yes
RADIUS DNS Host Name Support Yes Yes
RADIUS Start/Stop Accounting Yes Yes
802.1x Yes Yes
802.1d bridging Yes Yes
MAC Access Control Table Yes Yes
Protocol Filtering Yes Yes
Multicast/Broadcast Storm Filtering Yes Yes
Proxy ARP Yes Yes
ICMP Echo Response Yes Yes
Hardware Watchdog Timer Yes Yes
Roaming Yes Yes
Link Integrity Yes Yes
Automatic Channel Select Yes Yes
WEP Yes Yes Key lengths supported by AP-600b:
64-bit and 128-bit
Key lengths supported by AP-600a:
64-bit, 128-bit, and 152-bit
WEP Plus (Weak Key Avoidance) No Yes Available only one way (AP to client) if
using an
ORiNOCO 802.11a/b ComboCard or a
non-ORiNOCO client.
WDS Relay No Yes
Remote Link Test No Yes
Link Test Responder No Yes*
Medium Density Distribution No Yes*
Distance between APs No Yes*
Ultra High Density No Yes*
Closed System No Yes
Interference Robustness No Yes
Load Balancing No Yes*
SpectraLink VoIP Support No Yes
Fragmentation Yes Yes For AP-600b, Fragmentation is
implemented as part of the Interference
Robustness feature.
Blocking Intra BSS Clients Yes Yes
Packet Forwarding Yes Yes
TCP/UDP Port Filtering Yes Yes
Dynamic Frequency Selection (DFS) Yes No DFS is required for 802.11a products
sold in Europe
Per User Per Session Encryption Yes No Use in conjunction with 802.1x
Syslog Messaging Yes Yes
2X Turbo Mode Yes No Not available in all countries