User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
RADIO APPROVALS
To determine whether you are allowed to use your device in the countries listed below, please check the “transmitter
number” that is printed on the identification label of your device.
Certifications radio
Pour déterminer si vous êtes autorisé à utiliser votre dispositif dans les pays indiquées ci-dessous, veuillez contrôler le
“numéro de l’émetteur” imprimé sur l’étiquette d’identification de votre dispositif.
Country
Pays
Radio Transmitter
Émetteur Radio
Approval Reference
Numéro du Permis
Restrictions
Restrictions
Canada Alpha-1: A13QBF IC: 1856-A13QBF
• For indoor use only.
• Pour usage intérieur uniquement.
Alpha-1: B11FNF IC: 1856-B11FNF
• System with outdoor antenna requires
licence from Industry Canada.
• Les systèmes dotés d’une antenne
extérieure nécessitent la délivrance d’une
licence de la part de Industry Canada.
USA Alpha-1: A13QBF FCC ID: HZB-A13QBF
• For indoor use only.
Alpha-1: B11FNF FCC ID: HZB-B11FNF
For Radio Type Number with the format x-yy-zzz:
x = A identifies a IEEE 802.11a compliant WLAN radio product for the 5 GHz frequency band.
B identifies a IEEE 802.11b compliant WLAN radio product for the 2.4 GHz frequency band.
yy = 04, 08, 09, 11, 13 or 14 identifies the number of channels.
Le code pour le type de radio a le format x-yy-zzz:
x = A indique un produit conforme à la norme IEEE 802.11a avec une radio à 5 GHz.B indique un produit conforme à
la norme IEEE 802.11b avec une radio à 2,4 GHz.
yy = 04, 08, 09, 11, 13 ou 14 indique le nombre de canaux.