User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Specifications
131
The AP-600a can operate on the following Channels in the European countries that allow operation in the
5.15-5.25 GHz band:
Japan (MKK)
The AP-600a can operate on the following Channels in Japan:
Singapore
The AP-600a can operate on the following Channels in Singapore:
127(
127(127(
127(
Channels 42, 152, and 160 are the available Channels when 2X Turbo mode is enabled. These Channels are
unavailable when 2X Turbo mode is disabled.
802.11b Channel Frequencies for the AP-600b
The following table shows the 802.11b channel allocations that vary from country to country.
Channel ID Center Frequency
(GHz)
Channel ID Center Frequency
(GHz)
36 5.180
52 5.260
40 5.200
56 5.280
44 5.220
60 5.300
48 5.240
64 5.320
Channel ID Center Frequency
(GHz)
34 5.170
38 5.190
42 5.210
46 5.230
Channel ID Center Frequency
(GHz)
Channel ID Center Frequency
(GHz)
36 5.180
152 (see note) 5.760
40 5.200
153 5.765
42 (see note) 5.210
157 5.785
44 5.220
160 (see note) 5.800
48 5.240
161 5.805
149 5.745
165 5.825
Channel ID FCC/World
(GHz)
ETSI
(GHz)
France
(GHz)
Japan
(GHz)
1 2.412 2.412 - 2.412
2 2.417 2.417 - 2.417
3 2.422 2.422 - 2.422
4 2.427 2.427 - 2.427
5 2.432 2.432 - 2.432
6 2.437 2.437 - 2.437
7 2.442 2.442 - 2.442
8 2.447 2.447 - 2.447
9 2.452 2.452 - 2.452
10 2.457 2.457 2.457 2.457
11 2.462 2.462 2.462 2.462
12 - 2.467 2.467 2.467
13 - 2.472 2.472 2.472
14 2.484