User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
126
RADIUS Authentication
127(
127(127(
127(
Use a server name only if you have enabled the DNS Client functionality. See DNS Client for RADIUS Name
Resolution.
RADIUS Accounting
127(
127(127(
127(
Use a server name only if you have enabled the DNS Client functionality. See DNS Client for RADIUS Name
Resolution.
RADIUS Accounting
Status
Integer enable
disable (disable)
RW radaccstatus
Accounting Inactivity
Timer
Integer32 0 – 2147483647
minutes; default is 5 min.
RW radaccinactivetmr
Name Type Values Access CLI Parameter
RADIUS Authentication Table N/A R radiustbl
Primary RADIUS Integer 1 R index
Backup RADIUS Integer 2 R index
RADIUS Server Status Integer enable
disable (default)
RW status
Server Addressing
Format (see note)
Integer ipaddr (default)
name
RW seraddrfmt
Server IP Address or
Name
IpAddress
DisplayString
User Defined
(enter an IP address if
seraddrfmt is ipaddr or a
name if set to name; up
to 254 characters if
using a name)
RW ipaddr
Port (optional) Integer User Defined
1812 (default)
RW port
Shared Secret DisplayString User Defined
max 63 characters
W ssecret
Response Time (sec) Integer 1 – 4 seconds
3 sec (default)
RW responsetm
Maximum
Retransmissions
(optional)
Integer 1 – 10
3 (default)
RW maxretx
Name Type Values Access CLI Parameter
RADIUS Accounting Table N/A R radacctbl
Primary RADIUS Integer 1 R index
Backup RADIUS Integer 2 R index
RADIUS Server Status Integer enable
disable (default)
RW status
Server Addressing
Format (see note)
Integer ipaddr (default)
name
RW seraddrfmt
Server IP Address or
Name
IpAddress
Display String
User Defined
(enter an IP address if
seraddrfmt is ipaddr or a
name if set to name; up
to 254 characters if
using a name)
RW ipaddr
Port (optional) Integer User Defined
1813 (default)
RW port
Shared Secret DisplayString User Defined
max 63 characters
W ssecret
Response Time (sec) Integer 1 – 4 seconds
3 sec (default)
RW responsetm
Maximum
Retransmissions
(optional)
Integer 1 – 10
3 (default)
RW maxretx