User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
125
127(
127(127(
127(
See WEP Encryption for information on the supported WEP Key lengths.
Security Encryption Key Length Table
The following table details how to set the Encryption Key Length for the wireless interfaces.
127(
127(127(
127(
The available Encryption Key Lengths vary based on model. The AP-600a supports 64, 128, or 152 bits. The
AP-600b supports 64 bits or 128 bits.
MAC Access Control Parameter
MAC Access Control Table
RADIUS Parameters
Primary and Backup RADIUS Server Table Parameters
ORiNOCO devices that use RADIUS authentication and/or accounting support both primary and backup RADIUS
servers. The configuration parameters and statistics are the same for both primary and backup servers. The CLI
differentiates the primary and backup RADIUS parameters by using the table index.
General RADIUS Parameters
Name Type Values Access CLI Parameter
Security Encryption Key
Length Table
Table N/A R secenckeylentbl
Index Integer 3 N/A index
Encryption Key Length Integer 64 bit
128 bit
152 bit
RW enckeylen
Name Type Values Access CLI Parameter
MAC Address Control Group N/A R macacl
Status Integer enable
disable (default)
RW macaclstatus
Operation Type Integer passthru (default)
block
RW macacloptype
Name Type Values Access CLI Parameter
MAC Address Control
Table
Table N/A R macacltbl
Table Index N/A N/A R index
MAC Address PhysAddress User Defined RW macaddr
Comment (optional) DisplayString User Defined
max 254 characters
RW cmt
Status (optional) Integer enable (default)
disable
RW status
Name Type Values Access CLI Parameter
RADIUS Group N/A R radius
MAC Access Control
Status
Integer enable
disable (disable)
R radmacacctrl
Authorization Lifetime Integer32 60 – 43200 seconds
900 sec. (default)
RW radauthlifetm
MAC Address Format Integer dashdelimited (default)
colondelimited
singledashdelimited
no delimiter
RW radmacaddrformat