User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
123
Bridge Parameters
Spanning Tree Parameters
Spanning Tree Priority and Path Cost Table
Storm Threshold Parameters
Storm Threshold Table
Name Type Values Access CLI Parameter
Spanning Tree Group N/A R stp
Spanning Tree Status Integer enable
disable (default)
RW stpstatus
Bridge Priority Integer 0 – 65535
32768 (default)
RW stppriority
Maximum Age Integer 600 – 4000
(in 0.01 sec intervals;
i.e., 6 to 40 seconds)
2000 (default)
RW stpmaxage
Hello Time Integer 100 – 1000
(in 0.01 sec intervals;
i.e., 1 to 10 seconds)
200 (default)
RW stphellotime
Forward Delay Integer 400 – 3000
(in 0.01 sec intervals;
i.e., 4 to 30 seconds)
1500 (default)
RW stpfwddelay
Name Type Values Access CLI Parameter
Spanning Tree Table Table N/A R stpbl
Table Index (Port) N/A 1 – 15 R index
Priority Integer 0 – 255
128 (default)
RW priority
Path Cost Integer 1 – 65535
100 (default)
RW pathcost
State Integer disable
blocking
listening
learning
forwarding
broken
Rstate
Status Integer enable
disable
RW status
Name Type Values Access CLI Parameter
Storm Threshold Group N/A N/A stmthres
Broadcast Threshold Integer 0 – 255 packets/sec
(default is 0)
RW stmbrdthres
Multicast Threshold Integer 0 – 255 packets/sec
(default is 0)
RW stmmultithres
Name Type Values Access CLI Parameter
Storm Threshold Table Table N/A R stmthrestbl
Table Index Integer 1 = Ethernet
3 = Wireless
R index
Broadcast Threshold Integer 0 – 255 packets/sec
(default is 0)
RW bcast
Multicast Threshold Integer 0 – 255 packets/sec
(default is 0)
RW mcast