User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
120
Ethernet Filtering Table
Identify the different filters by using the table index.
127(
127(127(
127(
The filter Operation Type (passthru or block) applies only to the protocol filters that are enabled in this table.
Static MAC Address Filter Table
Proxy ARP Parameters
IP ARP Filtering Parameters
Name Type Values Access CLI Parameter
Ethernet Filtering Table Table N/A R etherflttbl
Table Index N/A N/A R index
Protocol Number Octet String N/A RW protonumber
Protocol Name (optional) DisplayString RW protoname
Filter Comment DisplayString 2- 31 characters RW cmt
Status (optional) Integer enable (1)
disable (2)
delete (3)
RW status
Name Type Values Access CLI Parameter
Static MAC Address
Filter Table
Table N/A R staticmactbl
Table Index N/A N/A R index
Static MAC Address on
Wired Network
PhysAddress User Defined RW wiredmacaddr
Static MAC Address
Mask on Wired Network
PhysAddress User Defined RW wiredmask
Static MAC Address on
Wireless Network
PhysAddress User Defined RW wirelessmacaddr
Static MAC Address
Mask on Wireless
Network
PhysAddress User Defined RW wirelessmask
Comment (optional) DisplayString max 255 characters RW cmt
Status (optional) Integer enable (default)
disable
delete
RW status
Name Type Values Access CLI Parameter
Proxy ARP Group N/A R parp
Status Integer enable
disable (default)
RW parpstatus
Name Type Values Access CLI Parameter
IP ARP Filtering Group N/A R iparp
Status Integer enable
disable (default)
RW iparpfltstatus
IP Address IpAddress User Defined RW iparpfltipaddr
Subnet Mask IpAddress User Defined RW iparpfltsubmask