User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
117
127(
127(127(
127(
There is an inter-dependent relationship between the Distance between APs and the Multicast Rate. In
general, larger systems operate a lower average transmit rates.
Wireless Distribution System (WDS) Parameters (AP-600b Only)
127(
127(127(
127(
At this time, WDS is not available for the AP-600a.
Ethernet Interface Parameters
Load Balancing Integer enable (default)
disable
RW ldbalance
Medium Distribution Integer enable (default)
disable
RW meddendistrib
MAC Address PhyAddress 12 hex digits R macaddr
Supported Data Rates Octet String Reported in 500 Kb/sec
intervals:
2 (1 Mbits/sec)
4 (2 Mbits/sec) (default)
11 (5.5 Mbits/sec)
22 (11 Mbits/sec)
R suppdatarates
Transmit Rate Integer32 Reported in 500 Kb/sec
intervals:
0 (auto fallback - default)
2 (1 Mbits/sec)
4 (2 Mbits/sec)
11 (5.5 Mbits/sec)
22 (11 Mbits/sec)
RW txrate
Supported Frequency Channels Octet String Depends on Regulatory
Domain
R suppchannels
Physical Layer Type Integer dsss (direct sequence
spread spectrum) for
802.11b
R phytype
Regulatory Domain List DisplayString U.S./Canada -- FCC
Europe -- ETSI
Japan -- MKK
R regdomain
Distance between APs Multicast Rate
Large 1 and 2 Mbits/sec
Medium 1, 2, and 5.5 Mbits/sec
Small 1, 2, 5.5 and 11 Mbits/sec
Minicell 1, 2, 5.5 and 11 Mbits/sec
Microcell 1, 2, 5.5 and 11 Mbits/sec
Name Type Values Access CLI Parameter
WDS Table Table N/A R wdstbl
Port Index Integer 3.1 - 3.6 (Wireless) R portindex
Status Integer enable, disable RW status
Partner MAC Address PhysAddress User Defined RW partnermacaddr
Name Type Values Access CLI Parameter
Ethernet Interface Group N/A R ethernet
Speed Integer 10halfduplex
10fullduplex
10autoduplex
100halfduplex
100fullduplex
autohalfduplex
autoautoduplex (default)
RW etherspeed
MAC Address PhyAddress N/A R ethermacaddr
Name Type Values Access CLI Parameter