User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
116
AP-600a Only Parameters
AP-600b Only Parameters
Name Type Values Access CLI Parameter
Operating Frequency Channel Integer Varies by regulatory
domain and country. See
802.11a Channel
Frequencies for the
AP-600a
RW channel
2X Turbo Mode
(not available in all countries)
Integer enable
disable (default)
RW turbo
Supported Data Rates Octet String See Transmit Rate,
below
R suppdatarates
Transmit Rate Integer32 Reported in 500 Kb/sec
intervals:
0 - Auto Fallback
(default)
12 (6 Mbits/sec)
18 (9 Mbits/sec)
24 (12 Mbits/sec)
36 (18 Mbits/sec)
48 (24 Mbits/sec)
72 (36 Mbits/sec)
96 (48 Mbits/sec)
108 (54 Mbits/sec)
For Turbo mode (not
available in all
countries):
0 - Auto Fallback
(default)
24 (12 Mbits/sec)
38 (18 Mbits/sec)
48 (24 Mbits/sec)
72 (36 Mbits/sec)
96 (48 Mbits/sec)
144 (72 Mbits/sec)
192 (96 Mbits/sec)
216 (108 Mbits/sec)
RW txrate
Physical Layer Type Integer ofdm (orthogonal
frequency division
multiplexing) for 802.11a
R phytype
Regulatory Domain List DisplayString FCC (5.15-5.35 GHz,
5.725-5.850 GHz)
ETSI (5.15-5.25 GHz
only)
ETSI (5.15-5.35 GHz)
MMK (5.15-5.25 GHz)
Singapore (5.15-2.25
GHz, 5.725-5.850 GHz)
R regdomain
Name Type Values Access CLI Parameter
Distance between APs Integer large (default)
medium
small
minicell
microcell
RW distaps
Interference Robustness Integer enable (default)
disable
RW interrobust
Operating Frequency Channel Integer 1 - 14; available channels
vary by regulatory
domain/country; see
802.11b Channel
Frequencies for the
AP-600b
RW channel
Multicast Rate Integer 1 Mbits/sec (1)
2 Mbits/sec (2) (default)
5.5 Mbits/sec (3)
11 Mbits/sec (4)
RW multrate
Closed Wireless System Integer enable
disable (default)
RW closedsys