User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
115
Link Integrity Parameters
Link Integrity IP Target Table
Interface Parameters
Wireless Interface Parameters
The wireless interface group parameter is wif. The interface uses table index 3.
Common Parameters to AP-600a and AP-600b
127(
127(127(
127(
For AP-600a units in Europe, Auto Channel Select is a read-only parameter; it is always enabled.
Name Type Values Access CLI Parameter
Link Integrity Group N/A R linkint
Link Integrity Status Integer enable
disable (default)
RW linkintstatus
Link Integrity Poll
Interval
Integer 500 - 15000 ms
(in increments of 500ms)
500 ms (default)
RW linkintpollint
Link Integrity Poll
Retransmissions
Integer 0 - 255
5 (default)
RW linkintpollretx
Name Type Values Access CLI Parameter
Link Integrity IP Target
Table
Table N/A R linkinttbl
Table Index Integer 1-5 N/A index
Target IP Address IpAddress User Defined RW ipaddr
Comment (optional) DisplayString User Defined (up to 254
characters)
RW cmt
Status (optional) Integer enable
disable (default)
delete
RW status
Name Type Values Access CLI Parameter
Wireless Interfaces Group N/A R wif
Table Index Integer 3 R index
Network Name DisplayString 1 – 31 characters
My Wireless Network A
(default)
RW netname
Auto Channel Select (ACS) Integer enable (default)
disable
RW autochannel
DTIM Period Integer 1 – 65535
1 = default
RW dtimperiod
RTS/CTS Medium Reservation Integer 0 – 2347
Default is 2347 (off)
RW medres
MAC Address PhyAddress 12 hex digits R macaddr
Supported Frequency Channels Octet String Depends on Regulatory
Domain
R suppchannels