User Manual
Table Of Contents
- Contents
- Introduction
- Installation & Basic Configuration
- Status Information
- Advanced Configuration
- Configuring the AP-600 Using the HTTP Interface
- System
- Network
- Interfaces
- Management
- Filtering
- Ethernet Protocol
- Static MAC
- Static MAC Filter Examples
- Prevent Two Specific Devices from Communicating
- Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
- Prevent All Wireless Devices From Communicating With a Single Wired Device
- Prevent A Wireless Device From Communicating With the Wired Network
- Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
- Static MAC Filter Examples
- Advanced
- TCP/UDP Port
- Alarms
- Bridge
- Security
- RADIUS
- Monitor Information
- Commands
- Troubleshooting
- Troubleshooting Concepts
- Symptoms and Solutions
- Recovery Procedures
- System Alarms (Traps)
- Related Applications
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables & User Strings
- Configuring the AP-600 using CLI commands
- Set Basic Configuration Parameters using CLI Commands
- Other Network Settings
- Configure the AP-600 as a DHCP Server
- Configure the DNS Client
- Maintain Client Connections using Link Integrity
- Change your Wireless Interface Settings
- Autochannel Select (ACS)
- [Device Name]>set wif 3 autochannel
[Device Name]>reboot 0 - Enable 2X Turbo Mode (AP-600a Only)
- [Device Name]>set wif 3 turbo
[Device Name]>reboot 0 - Enable/Disable Interference Robustness (AP-600b Only)
- Enable/Disable Closed System (AP-600b Only)
- Enable/Disable Load Balancing (AP-600b Only)
- Enable/Disable Medium Density Distribution (AP-600b Only)
- Set the Distance Between APs (AP-600b Only)
- Set the Multicast Rate (AP-600b Only)
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure MAC Access Control
- Configure 802.1x Authentication
- Set RADIUS Parameters
- CLI Monitoring Parameters
- Parameter Tables
- ASCII Character Chart
- Specifications
- Technical Support
Command Line Interface (CLI)
114
DNS Client for RADIUS Name Resolution
DHCP Server Parameters
127(
127(127(
127(
The DHCP Server (dhcpstatus) can only be enabled after a DHCP IP Pool table entry has been created.
DHCP Server table for IP pools
127(
127(127(
127(
Set either End IP Address or Width (but not both) when creating an IP address pool.
Name Type Values Access CLI Parameter
DNS Client Group N/A R dns
DNS Client status Integer enable
disable (default)
RW dnsstatus
Primary DNS Server IP
Address
IpAddress User Defined RW dnspridnsipaddr
Secondary DNS Server
IP Address
IpAddress User Defined RW dnssecdnsipaddr
Default Domain Name Integer32 User Defined (up to 254
characters)
RW dnsdomainname
Name Type Values Access CLI Parameter
DHCP Server Group N/A R dhcp
DHCP Server Status Integer enable (1) (default)
disable (2)
delete (3)
RW dhcpstatus
Gateway IP Address IpAddress User Defined RW dhcpgw
Primary DNS IP Address IpAddress User Defined RW dhcppridnsipaddr
Secondary DNS IP
Address
IpAddress User Defined RW dhcpsecdnsipaddr
Number of IP Pool Table
Entries
Integer32 N/A R dhcpippooltblent
Name Type Values Access CLI Parameter
DHCP Server IP Address
Pool Table
Table N/A R dhcpippooltbl
Table Index Integer User Defined N/A index
Start IP Address IpAddress User Defined RW startipaddr
End IP Address IpAddress User Defined RW endipaddr
Width Integer User Defined RW width
Default Lease Time
(optional)
Integer32 > 0
86400 sec (default)
RW defleasetm
Maximum Lease Time
(optional)
Integer32 > 0
86400 sec (default)
RW maxleasetm
Comment (optional) DisplayString User Defined RW cmt
Status (optional) Integer enable (1)
disable (2)
delete (3)
RW status