User Guide for the ORiNOCO AP-600 The Capacity to Do Great Things.
Copyright © 2002 Proxim Corporation. All rights reserved. Covered by one or more of the following U.S. patents: 5,231,634; 5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Proxim Corporation.
ORiNOCO AP-600 User’s Guide Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Introducing the AP-600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The Product Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Logging into the HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 4 Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Storm Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Intra BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 Troubleshooting Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Symptoms and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Connectivity Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 RADIUS Authentication Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 TFTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 A Command Line Interface (CLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Configure the AP-600 as a DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Configure the DNS Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Maintain Client Connections using Link Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Spanning Tree Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Storm Threshold Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Intra BSS Subscriber Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction 1 In This Chapter • • • • • • • • Introducing the AP-600 The Product Package System Requirements IEEE 802.11 Specifications Wireless Networking Concepts Management and Monitoring Capabilities Active Ethernet Software Features Introducing the AP-600 The AP-600 is a high performance wireless Access Point that includes an integrated antenna and radio. The AP-600 comes in two models: AP-600a, which complies with the IEEE 802.11a wireless standard, and AP-600b, which complies with the IEEE 802.
Introduction The Product Package Each AP-600 comes with the following: • • • • • One metal base for ceiling or desktop mounting (includes two screws) Mounting hardware – Four 3.
Introduction Wireless Networking Concepts The AP-600 extends the capability of an existing Ethernet network to devices on a wireless network. Wireless devices can connect to a single Access Point, or they can move between multiple Access Points located within the same vicinity. As wireless clients move from one coverage cell to another, they maintain network connectivity.
Introduction Management and Monitoring Capabilities There are several management and monitoring interfaces available to the network administrator to configure and manage an AP-600 on the network: • • • • HTTP Interface Command Line Interface SNMP Management Wireless Network Manager HTTP Interface The HTTP Interface (Web browser Interface) provides easy access to configuration settings and network statistics from any computer on the network.
Introduction Wireless Network Manager The Wireless Network Manager is Proxim’s premier management tool for Access Points and Outdoor Routers. It provides a single management interface that lets an IT manager configure, manage, upgrade, and troubleshoot thousands of wireless devices from anywhere in the world. The Wireless Network Manager simplifies network maintenance and easily integrates in an existing SNMP management system. See Proxim’s Web site at http://www.proxim.
Introduction Software Features The table below compares the software features available for the AP-600a and the AP-600b: Feature Number of stations per Basic Service Set (BSS) AP-600a AP-600b 802.11a 802.
Introduction The following table provides detailed information on the some of the differences between the 802.11a and 802.11b feature sets. AP-600a (802.11a) AP-600b (802.
Installation & Basic Configuration 2 In This Chapter This chapter describes how to install and configure an AP-600 for the first time. • • • • • Prerequisites Installation Initialization Download the Latest Software Additional Hardware Features Prerequisites Before installing an AP-600, you need to gather certain network information. The following section identifies the information you need.
Installation & Basic Configuration Installation Follow these steps to install an AP-600: 1. Unpack the Access Point and accessories from the shipping box. 2. If you intend to install the unit free-standing or if you intend to mount it to the ceiling, use a Phillips screwdriver to attach the metal base to the underside of the unit. The metal base and screws are provided. See Mounting Options for additional information. Figure 2-1 Attach the Metal Base 3.
Installation & Basic Configuration Figure 2-3 Remove Cable Cover 5. Remove the front cover (the side with the LED indicators) from the unit. Figure 2-4 Remove the Front Cover 6. Remove the back cover from the unit.
Installation & Basic Configuration Figure 2-5 Remove the Back Cover 7. Connect one end of an Ethernet cable to the Access Point’s Ethernet port. The other end of the cable should not be connected to another device until after the installation is complete. • Use a straight-through Ethernet cable if you intend to connect the Access Point to a hub, switch, patch panel, or Active Ethernet power injector. • Use a cross-over Ethernet cable if you intend to connect the Access Point to a single computer. 8.
Installation & Basic Configuration 127( Once attached, the power cable locks into place. To disconnect the power cable, slide back the black plastic fitting and gently pull the cable from the connector. 9. Connect the free end of the Ethernet cable to a hub, switch, patch panel, Active Ethernet power injector, or an Ethernet port on a computer. 10. If using AC power, connect the power cord to a power source (such as a wall outlet) to turn on the unit. 11. Configure and test the unit.
Installation & Basic Configuration Initialization Proxim provides two tools to simplify the initialization and configuration of an AP-600: • • ScanTool Setup Wizard ScanTool is included on the ORiNOCO CD; the Setup Wizard launches automatically the first time you access the HTTP interface. 127( These initialization instructions describe how to configure an AP-600 over an Ethernet connection using ScanTool and the HTTP interface.
Installation & Basic Configuration Figure 2-8 Scan List 7. Locate the MAC address of the AP-600 you want to initialize within the Scan List. 127( If your Access Point does not show up in the Scan List, click the Rescan button to update the display. If the unit still does not appear in the list, see Troubleshooting for suggestions. Note that after rebooting an Access Point, it may take up to five minutes for the unit to appear in the Scan List. 8.
Installation & Basic Configuration 3. 4. Set IP Address Type to Static. Enter a static IP Address for the AP-600 in the field provided. You must assign the unit a unique address that is valid on your IP subnet. Contact your network administrator if you need assistance selecting an IP address for the unit. 5. 6. 7. Enter your network’s Subnet Mask in the field provided. Enter your network’s Gateway IP Address in the field provided.
Installation & Basic Configuration Figure 2-10 Enter Network Password Figure 2-11 Setup Wizard 5. Click Setup Wizard to begin. If you want to configure the AP-600 without using the Setup Wizard, click Exit and see Advanced Configuration. The Setup Wizard supports the following navigation options: • Save & Next Button: Each Setup Wizard screen has a Save & Next button. Click this button to submit any changes you made to the unit’s parameters and continue to the next page.
Installation & Basic Configuration 8. Assign the AP-600 new passwords to prevent unauthorized access and click Save & Next. Each management interface has its own password: — SNMP Read Password — SNMP Read-Write Password — CLI Password — HTTP (Web) Password By default, each of these passwords is set to “public”. See Passwords for more information. 9. Configure the basic wireless interface settings and click Save & Next.
Installation & Basic Configuration — Multicast Rate: Sets the rate at which Multicast messages are sent. This value is related to the Distance Between APs parameter (described previously). The table below displays the possible Multicast Rates based on the Distance between APs. See Multicast Rate for more information. Distance between APs Multicast Rate — — Large 1 and 2 Mbits/sec Medium 1, 2, and 5.5 Mbits/sec Small 1, 2, 5.5 and 11 Mbits/sec Minicell 1, 2, 5.
Installation & Basic Configuration Download Updates from your TFTP Server using the Web Interface 1. 2. 3. 4. 5. 6. 7. 8. 9. Download the latest software from http://www.proxim.com/support/. Copy the latest software updates to your TFTP server. In the Web Interface, click the Commands button and select the Download tab. Enter the IP address of your TFTP server in the field provided. Enter the File Name (including the file extension). Enter the full directory path and file name.
Installation & Basic Configuration 7. Remove the back cover from the unit. See Remove the Back Cover for an illustration. 8. Place the back cover on the mounting location and mark the center of the three mounting holes. 9. Remove the cover from the wall and drill a hole at each of the locations you marked above. Each hole should be wide enough to hold a mounting plug (which is 6 mm x 35 mm). 10. Insert a plug into each hole.
Installation & Basic Configuration Figure 2-13 AP-600 Mounted on a Wall 15. Replace the front cover. 16. Replace the cable cover. 17. Turn on the AP-600. Ceiling Mount Follow these steps to mount the AP-600 to a ceiling: 1. Unplug the Access Point’s power supply, if necessary. 2. Use a Phillips screwdriver to attach the metal base to the underside of the AP-600, if necessary. See Attach the Metal Base for an illustration. 3. Feed a mounting screw through each of the four rubber feet.
Installation & Basic Configuration Figure 2-14 Mounting the AP-600 to the Ceiling Kensington Security Slot The AP-600 enclosure includes a Kensington Security Slot for use with a Kensington locking mechanism. When properly installed, a Kensington lock can prevent unauthorized personnel from stealing the AP-600. In addition, the Kensington locks secures the cable cover in place, which prevents tampering with the Ethernet and power cables.
Installation & Basic Configuration LED Indicators The AP-600 has four LED indicators.
Status Information 3 In This Chapter This chapter describes the statistical information that is reported within the Access Point’s HTTP interface. • • Logging into the HTTP Interface System Status Logging into the HTTP Interface Once the AP-600 has a valid IP Address and an Ethernet connection, you may use your web browser to monitor the system status. Follow these steps to monitor an AP-600’s operating statistics using the HTTP interface: 1. Open a Web browser on a network computer.
Status Information System Status System Status is the first screen to appear each time you connect to the HTTP interface. You can also return to this screen by clicking the Status button. Figure 3-2 System Status Screen Each section of the System Status screen provides the following information: – – System Status: This area provides system level information, including the unit’s IP address and contact information. See System for information on these settings.
Advanced Configuration 4 In This Chapter This chapter describes all of the operating parameters that can be configured using the Access Point’s HTTP interface. • • • • • • • • • • Configuring the AP-600 Using the HTTP Interface System: Configure specific system information such as system name and contact information. Network: Configure IP settings, DNS client, DHCP server, and Link Integrity. Interfaces: Configure the Access Point’s interfaces: Wireless and Ethernet.
Advanced Configuration Figure 4-1 Enter Network Password Screen 5. Click the Configure button located on the left-hand side of the screen. Figure 4-2 Configure Main Screen 6. Click the tab that corresponds to the parameter you want to configure. For example, click Network to configure the Access Point’s TCP/IP settings. The parameters contained in each of the nine configuration categories are described later in this chapter. 7. Configure the Access Point’s parameters as necessary.
Advanced Configuration System You can configure and view the following parameters within the System Configuration screen: • • • Name: The name assigned to the AP-600. Location: The location where the AP-600 is installed. Contact Name: The name of the person responsible for the AP-600. • • • Contact Email: The email address of the person responsible for the AP-600. Contact Phone: The telephone number of the person responsible for the AP-600.
Advanced Configuration • DNS Client Default Domain Name: The default domain name for the Access Point’s network (for example, “proxim.com”). Contact your network administrator if you need assistance setting this parameter. Advanced • Default TTL (Time to Live): Time to Live (TTL) is a field in an IP packet that specifies how long in seconds the packet can remain active on the network.
Advanced Configuration • • Gateway IP Address: The AP-600 will assign the specified address to its DHCP clients. Primary DNS IP Address: The AP-600 will assign the specified address to its DHCP clients. • • Secondary DNS IP Address: The AP-600 will assign the specified address to its DHCP clients. Number of IP Pool Table Entries: This is a read-only field that reports the number of IP address pools currently configured.
Advanced Configuration You can configure and view the following parameters within the Link Integrity Configuration screen: • • Enable Link Integrity: Place a check mark in the box provided to enable Link Integrity. Poll Interval (milliseconds): The interval between link integrity checks. Range is 500 - 15000 ms in increments of 500 ms; default is 500 ms. • Poll Retransmissions: The number of times a poll should be retransmitted before the link is considered down. Range is 0 to 255; default is 5.
Advanced Configuration • • • Transmit Rate: Use the drop-down menu to select a specific transmit rate for the AP-600a. Choose between 6, 9, 12, 18, 24, 36, 48, 54 Mbits/s, and Auto Fallback for standard 802.11a mode. If Turbo mode is enabled, choose between 12, 18, 24, 36, 48, 72, 98, 108 Mbits/s, and Auto Fallback. Auto Fallback is the default setting; it allows the AP-600a unit to select the best transmit rate based on the cell size.
Advanced Configuration RTS/CTS Medium Reservation The 802.11 standard supports optional RTS/CTS communication based on packet size. Without RTS/CTS, a sending radio listens to see if another radio is already using the medium before transmitting a data packet. If the medium is free, the sending radio transmits its packet. However, there is no guarantee that another radio is not transmitting a packet at the same time, causing a collision.
Advanced Configuration Figure 4-6 • Wireless Interface Configuration Screen (AP-600b) Multicast Rate: Sets the rate at which Multicast messages are sent. This value is related to the Distance Between APs parameter (described previously). The table below displays the possible Multicast Rates based on the Distance between APs setting. By default, this parameter is set to 2 Mbits/sec. See Multicast Rate for more information.
Advanced Configuration • • Load Balancing: Enable this option so clients can evaluate which Access Point to associate with, based on current AP loads. This feature is enabled by default; it helps distribute the wireless load between APs. This feature is not available if you are using an ORiNOCO 802.11a/b ComboCard or a non-ORiNOCO client with the AP-600b.
Advanced Configuration ! &$87,21 The distance between APs should not be approximated. It is calculated by means of a manual Site Survey, in which an AP-600b is set up and clients are tested throughout the area to determine signal strength and coverage, and local limits such as physical interference are investigated. From these measurements the appropriate cell size and density is determined, and the optimum distance between APs is calculated to suit your particular business requirements.
Advanced Configuration Wireless Distribution System (WDS) A Wireless Distribution System (WDS) creates a link between two AP-600b units over their radio interfaces. This link relays traffic from one AP-600b that does not have Ethernet connectivity to a second AP-600b that has Ethernet connectivity. WDS allows you to configure up to six (6) point-to-point links between Access Points. In the WDS Example below, AP 1 and AP 2 communicate over a WDS link (represented by the blue line).
Advanced Configuration To setup a wireless backbone follow the steps below for each AP-600b that you wish to include in the Wireless Distribution System. 1. Confirm that Auto Channel Select is disabled. 2. Write down the MAC Address of the radio that you wish to include in the Wireless Distribution System. Open the Wireless Interface Configuration screen. Scroll down to the Wireless Distribution System heading. Click the Edit button to update the Wireless Distribution System (WDS) Table.
Advanced Configuration Management The Management category contains three sub-categories. – – – Passwords IP Access Table Services Passwords You can configure the following passwords: • • • • SNMP Read Password: The password for read access to the AP-600 using SNMP. Enter a password in both the Password field and the Confirm field. The default password is “public”. SNMP Read/Write Password: The password for read and write access to the AP-600 using SNMP.
Advanced Configuration Services You can configure the following management services: 127( You must reboot the Access Point if you change the HTTP Port or Telnet Port. SNMP Settings • SNMP Interface Bitmask: Configure the interface or interfaces (Ethernet, Wireless, All Interfaces) from which you will manage the AP-600 via SNMP. You can also select Disabled to prevent a user from accessing the AP-600 device via SNMP.
Advanced Configuration Telnet Configuration Settings • • • • Telnet Interface Bitmask: Select the interface (Ethernet, Wireless, All Interfaces) from which you can manage the AP-600 via telnet. This parameter can also be used to Disable telnet management. Telnet Port: The default port number for Telnet applications is 23. However, you can use this field if you want to change the Telnet port for security reasons (but your Telnet application also must support the new port number you select).
Advanced Configuration 3. Configure the Ethernet Protocol Filter Table. This table is pre-populated with existing Ethernet Protocol Filters, however, you may enter additional filters by specifying the appropriate parameters. • To add an entry, click Add, and then specify the Protocol Number and a Protocol Name. — Protocol Number: Enter the protocol number. See http://www.iana.org/assignments/ethernet-numbers for a list of protocol numbers.
Advanced Configuration Figure 4-12 Static MAC Configuration Screen Static MAC Filter Examples Consider a network that contains a wired server and three wireless clients.
Advanced Configuration Prevent All Wireless Devices From Communicating With a Single Wired Device Configure the following settings to prevent all three Wireless Clients from communicating with Wired Server 1. • • • • Wired MAC Address: 00:40:F4:1C:DB:6A Wired Mask: FF:FF:FF:FF:FF:FF Wireless MAC Address: 00:00:00:00:00:00 Wireless Mask: 00:00:00:00:00:00 Result: The Access Point blocks all traffic between Wired Server 1 and all wireless clients.
Advanced Configuration TCP/UDP Port Port-based filtering enables you to control wireless user access to network services by selectively blocking TCP/UDP protocols through the AP-600. A user specifies a Protocol Name, Port Number, Port Type (TCP, UDP, or TCP/UDP), and filtering interfaces (Wireless only, Ethernet only, all interfaces, or no interfaces) in order to block access to services, such as Telnet and FTP, and traffic, such as NETBIOS and HTTP.
Advanced Configuration Alarms This category has three sub-categories. – – – Groups Alarm Host Table Syslog Groups There are seven alarm groups that can be enabled or disabled: • • • • • • • Enable Configuration Alarms Enable Security Alarms Enable Wireless Alarms Enable Operational Alarms Enable Flash Memory Alarms Enable TFTP Alarms Enable Image Alarms Place a check mark in the box provided to enable a specific group. Remove the check mark from the box to disable the alarms.
Advanced Configuration Event Priority Description LOG_EMERG 0 system is unusable LOG_ALERT 1 action must be taken immediately LOG_CRIT 2 critical conditions LOG_ERR 3 error conditions LOG_WARNING 4 warning conditions LOG_NOTICE 5 normal but significant condition LOG_INFO 6 informational LOG_DEBUG 7 debug-level messages Configuring Syslog Event Notifications You can configure the following Syslog settings from the HTTP interface: • • • • Enable Syslog: Place a check mark in the
Advanced Configuration Bridge The AP-600 is a bridge between your wired and wireless networking devices. As a bridge, the functions performed by the AP-600 include: • • • MAC address learning Forward and filtering decision making Spanning Tree protocol used for loop avoidance Once the AP-600 is connected to your network, it learns which devices are connected to it and records their MAC addresses in the Learn Table. The table can hold up to 10,000 entries.
Advanced Configuration Packet Forwarding The Packet Forwarding feature enables you to redirect traffic generated by wireless clients that are all associated to the same AP-600 to a single MAC address. This filters wireless traffic without burdening the AP-600 and provides additional security by limiting potential destinations or by routing the traffic directly to a firewall.
Advanced Configuration Figure 4-15 MAC Access Configuration Screen WEP Encryption The IEEE 802.11 standards specify an optional encryption feature, known as Wired Equivalent Privacy or WEP, that is designed to provide a wireless LAN with a security level equal to what is found on a wired Ethernet network. WEP encrypts the data portion of each packet exchanged on an 802.11 network using an Encryption Key (also known as a WEP Key). When Encryption is enabled, two 802.
Advanced Configuration Figure 4-16 Encryption Configuration Follow these steps to set up WEP encryption on an AP-600: 1. Place a check mark in the box labeled Enable Encryption (WEP). 2. Enter one to four Encryption Keys in the fields provided. Keep in mind the following: • If entering more than one Key, use the same number of characters for each Key. All Keys need to be the same Key Size (64, 128, or 152-bit). • You can enter the Encryption Keys in either hexadecimal or ASCII format.
Advanced Configuration • • • EAP-Transport Layer Security (TLS): Certificate-based authentication (a certificate is required on the server and each client); supports automatic key distribution EAP-Tunneled Transport Layer Security (TTLS): Certificate-based authentication (a certificate is required on the server; a client’s username/password is tunneled to the server over a secure connection); supports automatic key distribution PEAP - Protected EAP with MS-CHAP v2: Secure username/password-based authenti
Advanced Configuration Configuring Security Settings The AP-600 offers four security settings: 127( 802.1x settings are located under the 802.1x heading. WEP Encryption settings are located under the Encryption heading. • • • • No security or encryption WEP encryption only – See WEP Encryption for details. 802.1x security Mixed Mode (802.1x and WEP Encryption) 802.1x Security Follow these steps to enable 802.1x only: 1. Within the 802.1x Configuration screen, set 802.1x Security Mode to 802.1x. 2.
Advanced Configuration Mixed Mode (802.1x and WEP Encryption) Follow these steps to use both 802.1x and WEP Encryption simultaneously (clients that do not support 802.1x use WEP Encryption for security purposes): 1. Within the 802.1x Configuration screen, set 802.1x Security Mode to Mixed. 2. Select an Encryption Key Length. • The AP-600b supports 64-bit and 128-bit encryption. • The AP-600a supports 64-bit, 128-bit, and 152-bit encryption. 3. Enter a Re-keying Interval.
Advanced Configuration The back-up servers are optional, but when configured, the AP-600 will communicate with the back-up server if the primary server is off-line. After the AP-600 has switched to the backup server, it will periodically check the status of the primary RADIUS server every five (5) minutes. Once the primary RADIUS server is again online, the AP-600 automatically reverts from the backup RADIUS server back to the primary RADIUS server.
Advanced Configuration Figure 4-19 RADIUS Access Control Configuration Screen RADIUS Authentication with 802.1x You must configure a primary RADIUS Authentication server to use 802.1x security. A back-up server is optional. 127( Problems with RADIUS Server configuration or RADIUS Authentication should be referred to the RADIUS Server developer. Follow these steps to enable a RADIUS Authentication server for 802.1x security: Within the 802.1x Configuration screen, configure the 802.1x settings. See 802.
Advanced Configuration 12. Enter the maximum number of times an authentication request may be retransmitted in the Maximum Retransmissions field. Range is 1-4; default is 3. 13. If you are configuring a back-up server, repeat Steps 7 through 12 for the back-up server. 14. Click OK to save your changes. 15. Reboot the AP-600 device for these changes to take effect.
Advanced Configuration Figure 4-20 RADIUS Accounting Server Configuration 67
Advanced Configuration 68
Advanced Configuration 69
Advanced Configuration 70
Monitor Information 5 In This Chapter This chapter describes the statistical information that is reported within the Access Point’s HTTP interface. • • • • • • • • • Logging into the HTTP Interface Version: Provides version information for the Access Point’s system components. ICMP: Displays statistics for Internet Control Message Protocol packets sent and received by the AP-600. IP/ARP Table: Displays the AP-600’s IP Address Resolution table.
Monitor Information Figure 5-1 Enter Network Password Screen 5. Click the Monitor button located on the left-hand side of the screen. Figure 5-2 Monitor Main Screen 6. Click the tab that corresponds to the statistics you want to review. For example, click Learn Table to see the list of nodes that the AP-600 has discovered on the network. 7. If applicable, click the Refresh button to update the statistics. Version From the HTTP interface, click the Monitor button and select the Version tab.
Monitor Information • Version: Specifies the component’s version or build number. The Software Image version is the most useful information on this screen for the typical end user. Figure 5-3 Version Information Screen ICMP This tab provides statistical information for both received and transmitted messages directed to the AP-600. Not all ICMP traffic on the network is counted in the ICMP (Internet Control Message Protocol) statistics.
Monitor Information IP/ARP Table This tab provides information based on the Address Resolution Protocol (ARP), which relates MAC Address and IP Addresses. Figure 5-5 IP/ARP Table Learn Table This tab displays information relating to network bridging. It reports the MAC address for each node that the device has learned is on the network and the interface on which the node was detected. There can be up 10,000 entries in the Learn Table.
Monitor Information IAPP This tab displays statistics relating to client handovers and communications between ORiNOCO Access Points. Figure 5-7 IAPP Screen RADIUS This tab provides RADIUS authentication and accounting information for both the Primary and Backup RADIUS servers. 127( RADIUS authentication and accounting must be enabled for this information to be valid.
Monitor Information Interfaces This tab displays statistics for the Ethernet and wireless interfaces. The Operational Status can be up, down, or testing.
Monitor Information Link Test (AP-600b Only) This tab displays information on the quality of the wireless link to clients and other AP-600b units in the Wireless Distribution System. During a Link Test, the Access Point and the selected device exchange a series of packets to test the strength of the connection. The devices start by exchanging packets at the 11 Mbits/sec rate but fall back to the slower rates if necessary. 127( This feature is not available for the AP-600a.
Monitor Information • • • 5.5 Mbps (pkts): The number of packets received at the 5.5 Mbits/sec transmit rate since the start of the Link Test. 2 Mbps (pkts): The number of packets received at the 2 Mbits/sec transmit rate since the start of the Link Test. 1 Mbps (pkts): The number of packets received at the 1 Mbits/sec transmit rate since the start of the Link Test. 127( Click the Refresh automatically. Figure 5-11 button periodically to update the test results.
Monitor Information 76
Monitor Information 77
Commands 6 In This Chapter This chapter describes the commands that can be issued from the Access Point’s HTTP interface. • • • • • • Logging into the HTTP Interface Download: Download files from a TFTP server to the AP-600. Upload: Upload configuration files from the AP-600 to a TFTP server. Reboot: Reboot the AP-600 in the specified number of seconds. Reset: Reset all of the Access Point’s configuration settings to factory defaults.
Commands Figure 6-1 Enter Network Password Screen 5. Click the Commands button located on the left-hand side of the screen. Figure 6-2 Commands Main Screen 6. Click the tab that corresponds to the command you want to issue. For example, click Reboot to restart the unit.
Commands Download Use the Download tab to download Configuration, AP Image, and Bootloader files to the AP-600. A TFTP server must be running and configured to point to the directory containing the file. Figure 6-3 Download Command Screen If you don’t have a TFTP server installed on your system, install the TFTP server from the ORiNOCO CD. You can either install the TFTP server from the CD Wizard or run OEM-TFTP-Server.exe found in the CD’s Xtras/SolarWinds sub-directory.
Commands Figure 6-4 Upload Command Screen Reboot Use the Reboot tab to save configuration changes (if any) and reset the AP-600. Entering a value of 0 (zero) seconds causes an immediate reboot. Note that Reset, described below, does not save configuration changes. ! &$87,21 Rebooting the AP-600 will cause all users who are currently connected to lose their connection to the network until the AP-600 has completed the restart process and resumed operation.
Commands Reset Use the Reset tab to restore the AP-600 to factory default conditions. The AP-600 may also be reset from the RESET button located on the side of the unit. Since this will reset the Access Point’s current IP address, a new IP address must be assigned. Refer to Recovery Procedures for more information. ! &$87,21 Resetting the AP-600 to its factory default configuration will permanently overwrite all changes that have made to the unit.
Troubleshooting 7 In This Chapter If you are having problems with an AP-600, review the troubleshooting suggestions contained in this chapter. • • • • • Troubleshooting Concepts Symptoms and Solutions Recovery Procedures System Alarms (Traps) Related Applications 127( This section helps you locate problems related to the AP-600 device setup.
Troubleshooting Symptoms and Solutions Connectivity Issues Connectivity issues include any problem that prevents you from powering up or connecting to the AP-600. AP-600 Unit Will Not Boot - No LED Activity 1. Make sure your power source is operating. 2. Make sure all cables are connected to the AP-600 correctly. 3. If you are using Active Ethernet, make sure you are using a Category 5, foiled, twisted pair cable to power the AP-600. Serial Link Does Not Work 1.
Troubleshooting 3. To find the unit’s current IP address if using DHCP, open the IP Client Table in the DHCP Server and match the Access Point’s IP address to its MAC address (found on the product label). Alternatively, use ScanTool to identify an Access Point’s current IP address. 4. Once you have the current IP address, use the HTTP or CLI Interface to change the unit’s IP settings, if necessary. 5.
Troubleshooting Client Connection Problems Client Software Finds No Connection Make sure you have configured your client software with the proper Network Name and Security settings. Network Names and WEP Keys are typically allocated and maintained by your network administrator. Client PC Card Does Not Work 1. Make sure you are using the latest PC Card driver software. 2. Download and install the latest ORiNOCO client software from http://www.proxim.com/support/. Intermittent Loss of Connection 1.
Troubleshooting Recovery Procedures The most common installation problems relate to IP addressing. For example, without the TFTP server IP Address, you will not be able to download a new AP Image to the AP-600. IP Address management is fundamental. We suggest you create a chart to document and validate the IP addresses for your system. If the password is lost or forgotten, you will need to reset the AP-600 to default values.
Troubleshooting Forced Reload Procedure Use this procedure to erase the current AP Image and download a new AP Image. In some cases, specifically when a missing or corrupted AP Image prevents successful booting, you may need to use ScanTool or the Bootloader CLI to download a new executable AP Image. 127( This does not delete the AP-600’s configuration (in other words, the Forced Reload Procedure does not reset to device to factory defaults).
Troubleshooting 8. Enter the network’s Gateway IP Address, if necessary. You may need to contact your network administrator to get this address. You should only need to enter the default gateway address if the Access Point and the TFTP server are separated by a router. 9. Enter the IP address of your TFTP server in the field provided. 10. Enter the Image File Name (including the file extension). Enter the full directory path and file name.
Troubleshooting 7.
Troubleshooting 2. Under File -> Properties -> Settings -> ASCII Setup, enable the Send line ends with line feeds option. Result: HyperTerminal sends a line return at the end of each line of code. 3. Press the RESET button on the AP-600 (see RELOAD and RESET Buttons to identify the location of the RESET button). Result: The terminal display shows Power On Self Tests (POST) activity, and then displays a CLI prompt, similar to the example below. This process may take up to 90 seconds.
Troubleshooting System Alarms (Traps) Security Alarms oriTrapAuthenticationFailure A client has failed to authenticate using one of the following authentication methods: MAC Access Control Table, RADIUS MAC Authentication, or 802.1x Authentication (for 802.
Troubleshooting Related Applications RADIUS Authentication Server If you enabled RADIUS Authentication on the AP-600, make sure that your network’s RADIUS servers are operational. Otherwise, clients will not be able to log in. There are several reasons the authentication server services might be unavailable, here are two typical things to check: • • Make sure you have the proper RADIUS authentication server information setup configured in the AP-600.
Troubleshooting 92
Command Line Interface (CLI) A In This Appendix This section describes the AP-600’s Command Line (CLI) Interface. CLI commands can be used to initialize, configure, and manage the Access Point. – – CLI commands may be entered in real time through a keyboard or submitted with CLI scripts. The CLI is available through both the Serial Port interface and over the Ethernet interface using Telnet. 127( All CLI commands and parameters are case-sensitive.
Command Line Interface (CLI) • • • • • Group - A logical collection of network parameter information. For example, the System Group is composed of several related parameters. Groups can also contain Tables. All items for a given Group can be displayed with a show CLI Command. Image File - The Access Point software executed from RAM. To update an Access Point you typically download a new Image File. This file is often referred to as the “AP Image”.
Command Line Interface (CLI) Bootloader CLI The Bootloader CLI is a minimal subset of the normal CLI used to perform initial configuration of the AP-600. This interface is only accessible via the serial interface if the AP-600 does not contain a software image or a download image command over TFTP has failed. The Bootloader CLI provides you with the ability to configure the initial setup parameters as well as download a software image to the device.
Command Line Interface (CLI) CLI Command Types This guide divides CLI Commands into two categories: Operational and Parameter Controls. Operational CLI Commands These commands affect Access Point behavior, such as downloading, rebooting, and so on. After entering commands (and parameters, if any) press the Enter key to execute the Command Line.
Command Line Interface (CLI) Example 3. Display parameters for set and show Example 3a allows you to see every possible parameter for the set (or show) commands. Notice from example 3a that the list is very long. Example 3b shows how to display a subset of the parameters based on initial parameter letters. Example 3a. Display every parameter that can be changed [Device Name]>set ? . . . . Figure A-5 Result of “set ?” CLI command Example 3b.
Command Line Interface (CLI) Example 4. Display Prompts for Successive Parameters Enter the command, a space, and then ?. Then, when the parameter prompt appears, enter the parameter value. Result: The parameter is changed and a new CLI line is echoed with the new value (in the first part of the following example, the value is the IP Address of the TFTP server).
Command Line Interface (CLI) Figure A-8 Results of “help” CLI command 2. Complete command description and command usage can be provided by: [Device Name]>help [Device Name]> help history Shows content of Command History Buffer. The Command History Buffer stores command statements entered in the current session.
Command Line Interface (CLI) upload Uploads a text-based configuration file from the AP-600 to the TFTP Server. Executing upload with the asterisk character (“*”) will make use of the previously set/stored TFTP parameters. Executing upload without parameters will display command help and usage information. 1. Syntax to upload a file: [Device Name]>upload Example: [Device Name]>upload 192.168.1.100 APconfig.sys config 2.
Command Line Interface (CLI) Example 1: Configuring objects that require the device to be rebooted The following message is displayed every time the user has configured an object that requires the device to be rebooted. [Device Name]>set ipaddr 135.114.73.
Command Line Interface (CLI) Example 4 - Enable, Disable, or Delete a table entry or row The following example illustrates how to manage the second entry in a table.
Command Line Interface (CLI) 2. View all parameters in a table. Syntax: [Device Name]> show
Example:[Device Name]> show mgmtipaccesstbl Result: Displays the IP Access Table and its entries. Using Tables & User Strings Working with Tables Each table element (or parameter) must be specified, as in the example below. [Device Name]>set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0 Below are the rules for creating, modifying, enabling/disabling, and deleting table entries.Command Line Interface (CLI) Configuring the AP-600 using CLI commands Log into the AP-600 using HyperTerminal 1. 2. 3. Open your terminal emulation program (like HyperTerminal) and set the following connection properties: • Com Port: • Baud rate: 9600 • Data Bits: 8 • Stop bits: 1 • Flow Control: None • Parity: None Under File -> Properties -> Settings -> ASCII Setup, enable the Send line ends with line feeds option.
Command Line Interface (CLI) Figure A-12 Result of “show system” CLI Command Set Static IP Address for the AP-600 127( The IP Subnet Mask of the AP-600 must match your network’s Subnet Mask. [Device [Device [Device [Device [Device Name]>set ipaddrtype static Name]>set ipaddr Name]>set ipsubmask Name]>set ipgw
Command Line Interface (CLI) Set WEP Encryption for the Wireless Interface ! &$87,21 Wireless clients must be configured with the same encryption key to be able to communicate with the AP-600. The AP-600 can only support one Key Length (so each of the configured keys must have the same length). The available key sizes vary based on the Access Point’s model. See Security Encryption Key Length Table for more information. You can set up to four encryption keys.
Command Line Interface (CLI) Other Network Settings There are other configuration settings that you may want to set for the AP-600. Some of them are listed below.
Command Line Interface (CLI) Maintain Client Connections using Link Integrity [Device Name]>show linkinttbl (this shows the current links) [Device Name]>set linkinttbl <1-5 (depending on what table row you wish to address)> ipaddr [Device Name]>set linkintpollint [Device Name]>set linkintpollretx [Device Name]>set linkintstatus enable [Device Name
Command Line Interface (CLI) Set the Distance Between APs (AP-600b Only) [Device Name]>set wif 3 distaps [Device Name]>reboot 0 127( The distance between APs should not be approximated. It is calculated by means of a manual Site Survey, in which an AP-600 is set up and clients are tested throughout the area to determine signal strength and coverage, and local limits such as physical interference are investigated.
Command Line Interface (CLI) Set Telnet Session Timeouts [Device Name]>set tellogintout
Command Line Interface (CLI) Configure 802.1x Authentication [Device Name]>set secconfig [Device Name]>set secenckeylentbl 3 enckeylen <64bits, 128bits, 152bits (152 bits available with AP-600a only)> [Device Name]>set secrekeyint <60 – 65535 seconds; default is 900 sec> [Device Name]>reboot 0 127( If you set Security to 802.1x or Mixed, you also need to configure the RADIUS parameters. If you set Security to Mixed, you also need to configure WEP Encryption settings. See 802.
Command Line Interface (CLI) Figure A-18 Result of “show radius” CLI Command Configure RADIUS Accounting server [Device Name]>set radacctbl status seraddrfmt ipaddr port ssecret responsetm <1 to 4 seconds> maxretx <1 to 10 times> [Device Name]>show radacctbl Figure A-19 Results of “show radacctbl” CLI command CLI Monitoring Parameters Using the show command with the following table parameters will display operati
Command Line Interface (CLI) Parameter Tables Objects contain groups that contain both parameters and parameter tables. Use the following Tables to configure the Access Point.
Command Line Interface (CLI) System Parameters Name Type Values System Group N/A Name DisplayString User Defined RW Location DisplayString User Defined RW sysloc Contact Name DisplayString User Defined RW sysctname Contact E-mail DisplayString User Defined RW sysctemail Contact Phone DisplayString User Defined max 254 characters RW sysctphone FLASH Backup Interval Integer Flash Update Access R CLI Parameter system sysname 0 - 65535 seconds RW sysflashbckint 0 1 RW sy
Command Line Interface (CLI) DNS Client for RADIUS Name Resolution Name Type Values DNS Client Group N/A Access DNS Client status Integer enable disable (default) RW dnsstatus Primary DNS Server IP Address IpAddress User Defined RW dnspridnsipaddr Secondary DNS Server IP Address IpAddress User Defined RW dnssecdnsipaddr Default Domain Name Integer32 User Defined (up to 254 characters) RW dnsdomainname R CLI Parameter dns DHCP Server Parameters Name Type Values DHCP Server G
Command Line Interface (CLI) Link Integrity Parameters Name Type Values Link Integrity Group N/A Access Link Integrity Status Integer enable disable (default) RW linkintstatus Link Integrity Poll Interval Integer 500 - 15000 ms (in increments of 500ms) 500 ms (default) RW linkintpollint Link Integrity Poll Retransmissions Integer 0 - 255 5 (default) RW linkintpollretx R CLI Parameter linkint Link Integrity IP Target Table Name Type Values Link Integrity IP Target Table Table N/
Command Line Interface (CLI) AP-600a Only Parameters Name Type Values Operating Frequency Channel Integer Varies by regulatory domain and country. See 802.
Command Line Interface (CLI) Name Type Values Load Balancing Integer enable (default) disable RW ldbalance Medium Distribution Integer enable (default) disable RW meddendistrib MAC Address PhyAddress 12 hex digits R macaddr Supported Data Rates Octet String Reported in 500 Kb/sec intervals: 2 (1 Mbits/sec) 4 (2 Mbits/sec) (default) 11 (5.
Command Line Interface (CLI) Management Parameters SNMP Parameters Name Type Values SNMP Group N/A SNMP Management Interface Bitmask Interface Bitmask 0 or 2 - no interfaces (disable) 1 or 3 - Ethernet 4 or 6 - Wireless 5 or 7 - all interfaces (default is 7) Read Password DisplayString Read/Write Password DisplayString Access R CLI Parameter snmp RW snmpifbitmask User Defined public (default) max 63 characters W snmprpasswd User Defined public (default) max 63 characters W snmprwpassw
Command Line Interface (CLI) Serial Port Parameters Name Type Values Serial Group N/A Baud Rate Integer 2400, 4800, 9600 (default), 19200, 38400, 57600 Data Bits Integer Parity Integer Stop Bits Integer 1 Flow Control Value none (default) xon/xoff Access R CLI Parameter serial RW serbaudrate 8 R serdatabits none R serparity R serstopbits RW serflowctrl TFTP Server Parameters These parameters relate to upload and download commands.
Command Line Interface (CLI) Ethernet Filtering Table Identify the different filters by using the table index.
Command Line Interface (CLI) Broadcast Filtering Table Name Type Values Access CLI Parameter Broadcast Filtering Table Table N/A R broadcastflttbl Index Integer 1-5 N/A R index Protocol Name DisplayString N/A Direction Integer ethertowireless wirelesstoether both (default) RW direction protoname Status Integer enable disable (default) RW status TCP/UDP Port Filtering The following parameters are used to enable/disable the Port filter feature.
Command Line Interface (CLI) Alarms Parameters SNMP Table Host Table Parameters When creating table entries, you may either specifying the argument name followed by argument value. CLI applies default values to the omitted arguments. Due to the nature of the information, the only argument that can be omitted is the “comment” argument.
Command Line Interface (CLI) Bridge Parameters Spanning Tree Parameters Name Type Values Spanning Tree Group N/A Access Spanning Tree Status Integer enable disable (default) RW stpstatus Bridge Priority Integer 0 – 65535 32768 (default) RW stppriority Maximum Age Integer 600 – 4000 (in 0.01 sec intervals; i.e., 6 to 40 seconds) 2000 (default) RW stpmaxage Hello Time Integer 100 – 1000 (in 0.01 sec intervals; i.e.
Command Line Interface (CLI) Intra BSS Subscriber Blocking The following parameters control the Intra BSS traffic feature, which prevent wireless clients that are associated with the same AP-600 from communicating with each other: Name Type Values Intra BSS Traffic Group N/A Intra BSS Traffic Operation Integer passthru (default) block Access R RW CLI intrabss intrabssoptype Packet Forwarding Parameters The following parameters control the Packet Forwarding feature, which redirects wireless traff
Command Line Interface (CLI) 127( See WEP Encryption for information on the supported WEP Key lengths. Security Encryption Key Length Table The following table details how to set the Encryption Key Length for the wireless interfaces. Name Type Values Access CLI Parameter R secenckeylentbl Security Encryption Key Table Length Table N/A Index Integer 3 N/A index Encryption Key Length Integer 64 bit 128 bit 152 bit RW enckeylen 127( The available Encryption Key Lengths vary based on model.
Command Line Interface (CLI) RADIUS Accounting Status Integer enable disable (disable) RW radaccstatus Accounting Inactivity Timer Integer32 0 – 2147483647 minutes; default is 5 min. RW radaccinactivetmr RADIUS Authentication 127( Use a server name only if you have enabled the DNS Client functionality. See DNS Client for RADIUS Name Resolution.
Command Line Interface (CLI) Other Parameters IAPP Parameters Name Type Values IAPP Group N/A Access IAPP Status Integer enable (default) disable RW iappstatus Periodic Announce Interval (seconds) Integer 80 120 (default) 160 200 RW iappannint Announce Response Time Integer 2 seconds Handover Time-out Integer Max.
B ASCII Character Chart You can configure WEP Encryption Keys in either Hexadecimal or ASCII format. Hexadecimal digits are 0-9 and A-F (not case sensitive). ASCII characters are 0-9, A-F, a-f (case sensitive), and punctuation marks. Each ASCII character corresponds to two hexadecimal digits. The table below lists the ASCII characters that you can use to configure WEP Encryption Keys. It also lists the Hexadecimal equivalent for each ASCII character.
Specifications C In This Appendix • • Hardware Specifications Radio Specifications Hardware Specifications Physical Specifications AP-600 Unit (without metal base) Dimensions (H x W x L) = 3.5 x 17 x 21.5 cm (1.5 x 6.75 x 8.5 in.) Weight = 0.68 kg (1.50 lb.) Electrical Specifications Using the Power Adapter Voltage (Input) = 100 to 240 VAC (50-60 Hz) @ 0.
Specifications Active Ethernet Interface Category 5, foiled, twisted pair cables must be used to ensure compliance with FCC Part 15, subpart B, Class B requirements Standard 802.3af pin assignments HTTP Interface Microsoft Internet Explorer 5.5 or later (preferred), or Netscape 4.x or later. Radio Specifications For AP-600a: 802.11a radio certification is available in the U.S. (FCC), Canada (DOC), Japan (MKK), Europe (ETSI), Singapore, and Australia. For AP-600b: 802.
Specifications The AP-600a can operate on the following Channels in the European countries that allow operation in the 5.15-5.25 GHz band: Channel ID Center Frequency (GHz) Channel ID Center Frequency (GHz) 36 5.180 52 5.260 40 5.200 56 5.280 44 5.220 60 5.300 48 5.240 64 5.320 Japan (MKK) The AP-600a can operate on the following Channels in Japan: Channel ID Center Frequency (GHz) 34 5.170 38 5.190 42 5.210 46 5.
Specifications Wireless Communication Range The range of the wireless signal is related to the composition of objects in the radio wave path and the transmit rate of the wireless communication. Communications at a lower transmit range may travel longer distances. The range values listed in the Communications Range Chart are typical distances as calculated by Proxim’s development team for FCC-certified products.
Technical Support D If you are having a problem using an AP-600 and cannot resolve it with the information in Troubleshooting, gather the following information and contact ORiNOCO Technical Support: • • • • List of ORiNOCO products installed on your network; include the following: – Product names and quantity – Part numbers (P/N) – Serial numbers (S/N) List of ORiNOCO software versions installed – For the AP-600, check the HTTP interface’s Version screen – Include the source of the software version (e
Technical Support For Asia Pacific: Phone: +1 661-367-2230 E-mail: APACsupport@orinocowireless.com For Europe, the Middle East, and Africa (EMEA): Your local supplier in the EMEA region is trained to give you the support you require. Local suppliers have direct access to the ORiNOCO Technical Support Center and will help you in every way they can. Phone: +1 661-367-2230 E-mail: EMEAsupport@orinocowireless.
USA/Canada section from the products regulatory flyer: INFORMATION TO THE USER This document provides regulatory information for the following products: Wireless Base Station products such as the AP- 600 Base Station products are wireless network products based on IEEE 802.11 standards for wireless LANs as defined and approved by the Institute of Electrical and Electronics Engineers. Products designed according the IEEE 802.11a standard use Orthogonal Frequency Division Multiplexing (OFDM) radio technology.
INFORMATIONS POUR L’UTILISATEUR Ce document fournit des informations sur les réglementations concernant les produits suivants : • Les produits sans fil de la Base Station tels que la AP- 600. Les produits client et de la Base Station sont des produits pour réseaux sans fil conçus selon les normes IEEE 802.11 définies et approuvées par l’Institute of Electrical and Electronics Engineers (IEEE). Les produits conçus selon les normes IEEE 802.
United States Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
RADIO APPROVALS To determine whether you are allowed to use your device in the countries listed below, please check the “transmitter number” that is printed on the identification label of your device. Certifications radio Pour déterminer si vous êtes autorisé à utiliser votre dispositif dans les pays indiquées ci-dessous, veuillez contrôler le “numéro de l’émetteur” imprimé sur l’étiquette d’identification de votre dispositif.
