2 Mega Pixel Water-Proof IR Network Camera User Manual Please read this instruction carefully for correct use of the product
PROVISION-ISR I3-380IP04 User Manual 720P 30m IR Fixed Lens IP Bullet Camera For H.
Before use this product Before operation, we strongly advise users to read this manual and keep it properly for using later. This is product instructions not quality warranty. We may reserve the rights of amending the typographical errors, inconsistencies with the latest version, software upgrades and product improvements, interpretation and modification. These changes will be published in the latest version without special notification.
IP CAMERA USER MUANUAL Table of Contents 1 Introduction.........................................................................................................1 1.1 Summarization ............................................................................................................................. 1 1.2 Check Package Content ................................................................................................................ 1 1.3 Connection ..............................................
Page 1 IP CAMERA USER MUANUAL 1 Introduction 1.1 Summarization This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It adopts state of the art video processing chips. It utilizes most advanced technologies, such as video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to ensure this system more stable and reliable. This unit consists of two parts: the IP-CAM device and central management software (short for CMS).
Page 2 IP CAMERA USER MUANUAL 2 Installation 2.1 Install IP-CAM to Ethernet Network The connection of digital video server is show below. Figure 2-1 Connection Please connect the PC and IP-CAMERA in accordance with the above picture. The connection steps are shown as below: Step 1: Connect the monitor, microphone and network to the device. Step 2: Connect the power supply. Step 3: Install the device. 2.2 CMS and IP-Tool Installation Find CMS software from CD and then double click “Setup.
Page 3 IP CAMERA USER MUANUAL 3 IE Remote Access IP-Cam can be connected through LAN or WAN. Here only take IE browser (6.0) for example. The details are as follows: 3.1 LAN In LAN, there are two ways to access IP-Cam: 1. Access through IP-Tool; 2. Directly access through IE browser. 3.1.1 Access through IP-Tool Step 1: Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the PC from the CD. Step 2: Use IP-Tool to modify the network of IP-Cam.
Page 4 IP CAMERA USER MUANUAL For example, the network segment of this computer is 192.168.13.x under the local config table. So, please modify the IP address, Gateway of IP-Cam which must be in the same network segment with the computer. Modifying the network, you have to input the password and click “OK” button to save the setting. Note: The default user name is: admin. The default password is: 123456. The new IP address of this device will display as follows after modification.
Page 5 IP CAMERA USER MUANUAL IP address: 192.168.226.201 Subnet Mask: 255.255.255.0 Gateway: 192.168.226.1 HTTP: 80 Data port: 9008 The first time you used the IP-CAM, you should connect the device with the above default settings. Here take the Windows XP OS for example to introduce the setting steps. Step 1: Manual setup the IP address of the PC, the network segment should be as same as the default settings of IP-CAM.
Page 6 IP CAMERA USER MUANUAL Step 4: Input user name and password in the login dialog box and click “OK” button to enter into the live interface. You can manage and setup the IP-CAM in the IE client, such as changing IP address, upgrading the software., etc. 3.2 WAN Access through router or virtual server Step1: Make sure the device is well connected in LAN.
Page 7 IP CAMERA USER MUANUAL 4 Remote Preview 4.1 The Remote Preview Interface Fig 4-1 Remote Preview 1 4 7 10 People icon Zoom in Start record Enable audio 2 5 8 Fix size Zoom out Playback 3 6 9 Zoom in Full screen Snap When motion detection alarm is triggered, the people icon turns red. Click icon to zoom in the preview image to suitable size. Drag the cursor on the enlarged image to view suitable preview area. Click enlarged image. Click icon to full-screen the live image.
Page 8 IP CAMERA USER MUANUAL Fig 4-2 record playback interface After selecting the record date, the record files will be displayed in the record file list box. User can double click a certain record file to playback or check a certain file. Then click Play button to do playback. 4.3 Right-click Function Clicking right mouse will appear a pull-down list as below: Stream: There are two options. Turn off the live: Click this item will close present live preview.
Page 9 IP CAMERA USER MUANUAL scroll bar to view all snapped pictures.
Page 10 IP CAMERA USER MUANUAL 5 Remote Live Surveillance Functions of remote configurations include: System Configuration, Video Configuration, Alarm Configuration, Network Configuration and Advanced Configuration. User should firstly select the menu on the left, and then setup the relative parameters. When a user setup parameters of a certain device, other users can not setup this device. 5.1 System Configuration The “System configuration” includes two submenus: Basic Information and Date & Time. 5.1.
Page 11 IP CAMERA USER MUANUAL 5.1.2 Date & Time Configuration Setting steps: 1. Enter into "System Configuration" “Date & Time”. Refer to Fig 5-2: 2. Select “Modify Time " to self-define time. Choose "Time Zone" according to user’s location. 3. Set DST as required. 4. User can setup time by select the “Synchronize with NTP Server”. 5. Press the "Save" button to save the settings. Fig 5-2 Date &Time Config 5.
Page 12 IP CAMERA USER MUANUAL 2. User can adjust Brightness, Contrast, Hue and saturation of the picture. 3. Select white balance mode. 4. Sharpen, denoise , white balance, frequency, CVBS format and Day-Night mode are adjustable. 5. User also can enable the image mirror and image overturn function. 6. Press the "Save" button to save the settings. 5.2.2 Video Stream 1. Enter into "Video configuration" "Video Stream" to see a interface as shown in Fig 5-4: Fig 5-4 Video Stream 2. 3. 4. 5. 6. 7.
Page 13 IP CAMERA USER MUANUAL 5.2.4 Video Mask You can set 4 mask area at most. Fig 5-6 Video Mask Enable the mask, select color and transparent of the mask area and then drag the mouse to set the mask area. This will take you see a gridding area. After that, click “Save” button to save the settings. Then you will see a mask area on the live image. 5.3 Alarm Configuration Alarm configuration includes three submenus: Motion Detection Area, Motion Detection Trigger and Motion Detection Schedule. 5.3.
Page 14 IP CAMERA USER MUANUAL Fig 5-7 Motion Detection Area 5.3.2 Motion Detection Trigger 1. Enter into “Alarm Configuration" "Motion Detection Trigger" to display a interface as shown in Fig 5-8: 2. Check "Enable alarm" check box. Then all functions under this interface will be activated. 4. Trigger Email: Check “Attach picture” and select email addresses in the “Receival email address” text box(Email address shall be set first in the Mail config interface).
Page 15 IP CAMERA USER MUANUAL 5.3.3 Motion Detection Schedule Enter into “Alarm configuration" "Motion Detection schedule" interface as shown in Fig 5-9: Week schedule User could set the alarm time from Monday to Sunday for alarm everyday in one week. Note: The lengthwise means one day of a week; the rank means 24 hours of a day. Click on the pane to set the alarm hours. Green means selected area. Blank means unselected area. "Add": add the schedule for a special day.
Page 16 IP CAMERA USER MUANUAL Fig 5-10 Port Config 2. Input port number for IE access in the "HTTP Port" textbox. 3. Input the port number for audio & video transmission in the "Data Port" textbox. 5.4.2 Wired Enter into "Network Configuration""Wired" to see a tab shown as Figure 5-11: There are two options to setup IP: obtain an IP address automatically by DHCP protocol or manually input IP address and gateway by clicking “Use the following IP address”.
Page 17 IP CAMERA USER MUANUAL Fig 5-12 Transit 2. Check “transit enable”. Then save the setting. 3. Input www.upnpicp.com in IE address; download and install Active X. Then a window shows up as Fig 5-13: Fig 5-13 Login 4. Input the only device ID of the IP-CAM or user-defined name. And then input user name and password. Note: The default user name and password are “admin” and “123456” respectively. 5.4.4 Server Configuration Enter into “Network Configuration” “Server Config”.
Page 18 IP CAMERA USER MUANUAL 1. Check “Do you want IP Camera to connect Server. 2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then enable the auto report in the ECMS/NVMS when adding a new device. Then input the remaining information of the device in the ECMS/NVMS. After that, the system will auto allot a device ID. Please check it in the ECMS/NVMS. 3. Input the above-mentioned server IP, server port and device ID in the responding boxes.
Page 19 IP CAMERA USER MUANUAL 2) Fill in the registration form, then click "Submit" 3) Fill in the host name you want to apply for and press "Request Domain" (for example "home") 4) If there is no problem with the domain registration you will see the following message: “Your domain was successfully created.
Page 20 IP CAMERA USER MUANUAL Fig 5-16 DDNS Config Note: The steps to band a domain name for video surveillance server are as follows. Firstly, register a user name and a password to log on the website of service supplier, and then apply for a domain name online for the server. After that, users can visit the server through inputting the domain name at IE terminal. 2. Press the "Save" button to save the settings. Please refer to the following table for parameters and instructions of DDNS configuration.
Page 21 IP CAMERA USER MUANUAL Step 2: Click to enter the website. Step 3: Click "New User" in the right of homepage to register. For example: User ID is ‘abc’, and password is ‘123456’. The register dialog display as below: (2) Login Step 1: Return to homepage after registering successfully. Step 2: Click "Account Manager" on the right of homepage to login. Step 3: Input the username and password with the information that you have registered. Step 4: Click "Enter" key after filling in the textbox.
Page 22 IP CAMERA USER MUANUAL 3. Application Connect IP-CAMERA to the Network Client. Step 1: After popping up the login interface, fill in "Server" textbox with ‘*.dns2p.com’ to visit the Network Client of the IP-CAMERA. The domain set in ‘(3) Domain Setup’. According to the example above, fill in "Server" textbox with ‘IP-CAMERA.dns2p.com’. Step 2: Click "save" button to save the above setting. 5.4.7 RTSP Enter into “Network Configuration” “RTSP” interface as shown in Fig 5-17: Fig 5-17 RTSP 1.
Page 23 IP CAMERA USER MUANUAL icons for networked UPnP devices” in the “Network Tasks” list box. Then a information window will pop up. Click “YES” button to see a “Windows Components Wizard” dialog box pop up as shown below. Then press “Next” to continue. After finished the installation of configuring components, the UPnP icons will display. Users can double-click certain icon to connect the remote surveillance login interface through IE.
Page 24 IP CAMERA USER MUANUAL 4.Select the secure connection type at the Secure Connection pull down list according to user’ actual needs 5. Receival email address list: add email address into the list 6. Receival email address: receiver’s e-mail address 7. After all parameters setup, user can click “Test your account settings”. If email sent successful, a “Test Successful” window will pop up, if not, users can try other email addresses or check the setting.
Page 25 IP CAMERA USER MUANUAL Upgrade. 5.5.1 User Configuration Enter into "User Configuration" interface. Refer to Fig 5-22: Add user: 1. Clicking "Add" button pops up "Add user" dialog box. Please refer to Fig 5-23: Fig 5-22 User Configuration Fig 5-23 Add User Note: After bind physical address to the IP-CAM, user can access the device on this PC in network only. If the MAC address was ““00:00:00:00:00:00” which means it can be connected to any computers. 2.
Page 26 IP CAMERA USER MUANUAL MAC” text box. 6. Click “OK” button to modify user’s password and binding MAC address successfully. Delete user: 1. Select the user which needs to delete in the user configuration list box. 2. Clicking “Delete” button will pop up a confirm dialog box. Then click “OK” to delete the user. Note: The default super administrator cannot be deleted.
Page 27 IP CAMERA USER MUANUAL Fig 5-25 Security Configuration 5.5.3 Configure Backup & Restore Enter into Advanced configurationConfigure Backup & Restore Interface. to Fig 5-26. Import & Export Configuration: User can import or export the setting information from PC or to device. 1. Click “Browse” to select save path for import or export information on PC. 2.
Page 28 IP CAMERA USER MUANUAL Fig 5-27 Reboot device interface 5.5.5 Upgrade Enter into Advanced Configuration—Upgrade interface shown as Fig 5-28: 1. Click “Browse” button to select the save path of the upgrade file 2. Click “Upgrade server firmware” button to start upgrading the application program 3. The device will restart automatically 4. After you successfully update the software, click “OK” button to close IE and then re-open IE to connect IP-Cam.
Page 29 IP CAMERA USER MUANUAL 6 Mobile Surveillance This IP-CAM supports mobile surveillance by phones with Windows mobile, iPhone, Android and Blackberry OS. Please check the operation system version of mobile before use; and connect the IP-CAM to Internet. 6.1 Network Configuration Access device via LAN Step 1: Connect device via wireless router. Then checkmark DHCP both in router and device to automatically acquire IP address or enter the IP address manually.
Page 30 IP CAMERA USER MUANUAL 6.2 By Phones with iPhone OS Install through Iphone. Step 1: Open App Store software as shown in the figure on the left. Step2: Search “Provision Cam” and click “Free” button as shown in the figure on the right. Step 3: Click “Install App” button as shown in the figure on the left. Step 4: Input iTunes Store password and then click “OK”. The software will be installed automatically. Install Software through PC Step 1: Install iTunes store in PC and then login.
Page 31 IP CAMERA USER MUANUAL "Provision Cam" Instruction 1. Login Step 1: Choose network type. There are two network connection ways: 3G/3G +WIFI, enhanced video quality. This network supports main stream and sub stream. The real-time image will be displayed by using sub stream. 3G, normal video quality compared to the former network type. Step 2: Input server, account and password. Server: WAN IP address (or domain name) plus HTTP port of the device. For example: 210.21.183:89 or 123.dvrdydns.com:89.
Page 32 IP CAMERA USER MUANUAL ：Log off button. Click this button to return to the login interface. ：Screen mode button. You can choose 1，4，6，8，9， 13 or 16 screen display mode. ：Favorite channel display button. If you save your favorite channel in the favorite server list, clicking this button will directly play all favorite channels you have saved. ：Snap button. Choose the channel and click this button to capture the channel image. ：Local record button.
Page 33 IP CAMERA USER MUANUAL button behind the device name to delete this device. Edit device: Click button behind the device name to edit the information of this device. Backup & restore: It is recommended to click “Backup” button to reserve the information of all devices. Then you can click “Restore” button to restore all device information after you re-install the client or delete the device uncarefully.
Page 34 5. IP CAMERA USER MUANUAL Fig 2 Fig 3 Fig 4 Fig 5 CMS Function This function makes multi-device managements and preview come true. Step 1: Click to enable CMS function. When this icon turns green, it means this function is enabled. Step 2: Click to choose channel as shown in the right picture. After you choose the channel, click “ok”, the system will display the related image automatically. If channels have been added into the group, you can see the images by clicking the group name.
Page 35 IP CAMERA USER MUANUAL Favorite channels of the device Step 1: Click to enter into device management list. Click the device name to extend channel. Enlighten the channels to save favorite channels as shown in the following picture on the left. Step 2: Return to the main interface and click to play the favorite channels. button Favorite groups of CMS Enable CMS function and enlighten the group to save the favorite groups as shown in the following picture on the right.
Page 36 IP CAMERA USER MUANUAL 6.3 By Phones with Android Software Installation Step 1: Run “Play Store” (or Google market) program. Step 2: Search “Provision Cam”. Step 3: Press “Install” button. Step 4: Install the software subject to the notes. Once the downloading is done, the software will install automatically Login Menu Step 1: Configure the network of your device and mobile phone. Step 2: Input the WAN IP address/domain name and port of your device in the sever column.
Page 37 IP CAMERA USER MUANUAL Main Menu Live View The first picture The previous picture Next picture The last picture Zoom in Zoom out Delete Record Playback: Click “Playback” in the main menu interface to enter playback interface. Then choose the channel you want to playback. This will take you to see the record file. Click this file to play. Pause/Play Stop Forward Backward Server List: In the main menu interface, click “Server list” to see the above picture on the left hand.
Page 38 IP CAMERA USER MUANUAL Modify Server: Click button to modify the server information. Delete Server: Click button to delete the server information. Settings: In the main menu interface, click “Settings” to enter the settings interface where you can configure local settings. Click “Local” to enter local settings interface. In this interface, you can set favorite channel and storage. Favorite Channel: Check the favorite channels and click “Save” button to save these channels.
Page 39 IP CAMERA USER MUANUAL 7 Use method for IP-TOOL Updating through IP-Tool Note: Do not cut off power supply and internet when updating; If the device is unable to start because of the failure of upgrade, it needs to retrofit. First， acquire the IP-Tool from the supplier and then double click the IP-Tool icon to run this software. Then the device can be searched; if the device can’t be searched, please check whether the PC and the device connect to the network or not.
Page 40 IP CAMERA USER MUANUAL Modify IP address and click OK button to exit the dialog box, IP-Tool will display the new IP address. Upgrading Software Select the device and right click to choose “Update software” menu. Input the username and password. Then click “browse” button to choose the upgrade software. Finally, click “Update software” to start upgrading. When upgrading, please do not disconnect PC and the device and make sure the power is on.
Page 41 IP CAMERA USER MUANUAL Enter into Kernel upgrade dialog box, input user name and password, click “Browse” to select the Update file (mboot8180-8180) and click “Update” button to start updating. When upgrading, please do not disconnect PC to device and make sure the power is on. The update progress bar will display as below: After finishing upgrading, a message box will pop up. After a while, the device will restart automatically.
Page 42 IP CAMERA USER MUANUAL 8 Q&A Q: How to find my password if I forget it? A：Reset all settings by IP-Tool or contact your dealer. Default IP: 192.168.226.201 User name: admin Password: 123456 Q：Fail to connect devices through IE browser, why? A: Network doesn’t connect well. Please check the connection and make sure it connected well. B: IP is not available. Reset the valid IP. C: Web port number has been revised: contact administrator to get the correct port number. D: Exclude the above reasons.
Page 43 IP CAMERA USER MUANUAL Fig 4-1 Fig 4-2 ④ then click ok to finish setup. b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them. Q：No sound can be heard, why? A：Without connect audio input device. Please connect and try again. B: Without enable audio function at the corresponding channel. Please check AUDIO item to enable this function. Q：Why doesn’t the device connect to wireless? A: Check the statues of wireless router.
Page 44 IP CAMERA USER MUANUAL 9 Specification Model Image Sensor Effective Pixels Electronic Shutter Day & Night Min.
Page 45 Notes: IP CAMERA USER MUANUAL
Page 46 IP CAMERA USER MUANUAL
