Operation Manual

10
Notes on Safety Prevention
Thismachinecanonlybeoperated
safelywhentheoperating
instructionsandthepamphlet
containingthesafetyinstructions
havebeencompletelyreadand
strictlyadheredto.
Forfurthernotesonsafetyrefertoenclosed
Sheet.
Alwaysinspectcableandplugbeforeusing
machine.Onlyhavedamagerepairedbya
qualiedprofessional.
Makesuremachineisswitchedoffbefore
insertingpluginsocket.
Themachinemustnotbedampandmustnot
beoperatedinawetenvironment.
Cautionwithlonghair.Donotwearloose‑
ttingclothingwhileworking.
Secureyourworkpiecewithclamps.
Alwaysdirectpowercabletorearawayfrom
themachine.
Alwaysensurethatyouhaveasecurefooting
whileworking.
Intheinterestsofsafety,theauxiliaryhandle
(14)shouldalwaysbeused.
Watchoutfortheinitialtorquereactionofthe
drill,especiallywhendrillbitistight.
Safety clutch
Thesafetyclutchisactivatedifthedrill
becomesjammedorcaught.
Beforecarryingoutanyworkonthemachine
disconnectfrompowersupplybyremoving
plugfromsocket.
Thechuckkeyshouldalwaysbekeptinthe
holderprovidedonthecablesleeve.
When drilling with the impact activated use
hearing protection.Exposuretotheeffects
ofnoisemaycausehearingloss.
Use the additional handle (additional
handles) if it is (they are) supplied with the
tool.Lossofcontrolmaycauseinjurepeople.
When carrying out an activity where the
machining tool could touch hidden power
conductors or its own power cord, hold
the electromechanical tool by the insulated
surfaces.Touchingthemachiningtoolwith
a"live"electricalconductormaycausethe
exposedmetalpartsoftheelectromechanical
tooltobecome“live”andleadtoinjuryofthe
userbyelectricshock.
Intended Use
Themachineisintendedforimpactdrillingin
brick,concreteandstoneaswellasfordrilling
inwood,metal,ceramicsandplastics.Machines
withelectroniccontrolandright/leftrotationare
alsosuitableforscrewingandthread‑cutting.
Theuseraloneisresponsibleforanyliabilities
causedbyusageotherthanintended.
Putting into Operation
Incorrectoperationcanleadtodamage.
Thereforealwaysobservethefollowing
regulations:
‑ Sharpdrillbitsoptimiseperformancewhilst
minimizingwearonthemachine.
‑ Donotplacesuchloadsonthemachinethat
itceasestoturn.
‑ Changerotationaldirectiononlywhenthe
machineisnotmoving.
Thepowersupplyvoltagemustmatchthe
informationquotedonthetoolidentication
plate.Toolswitharatingof230Vcanalsobe
connectedtoa220V/240Vsupply.
Connecting the mains cable module
(Plug it)
Themachineisequippedwithaquick‑change
mainscablemodule(9).Bydisconnecting
themainscableandthemachine,bothcan
betransportedeasier.Insertthemainscable
module(9)intothesocket(17)ofthemachine
andsecurebyturningthesleeve(18)in
clockwisedirection.
Toundotheconnection,turnthesleeve(18)in
counterclockwisedirectionandpullthemains
cablemodule(9)fromthesocket(17).
Usethemainscablemoduleonlyfor
PROTOOLpowertools.Donotattemptto
operateothermachineswithit.
Auxiliary handle
Forsafetyreasonsalwaysusetheenclosed
auxiliaryhandle(14).Fastentheauxiliaryhandle
totheclampingcollar(2)withthewingbolt(3).
Bylooseningthewingbolt(15)thedrillingdepth
canbeadjustedwiththedepthstopadjustment
(16).Theauxiliaryhandleisusedtoguide
themachinesecurely,especiallywithsudden
occuringreactiontorque(e.g.jammingofthe
drillbit).