Operation Manual

12
Notes on Safety
Thismachinecanonlybeoperated
safelywhentheoperating
instructionsandthepamphlet
containingthesafetyinstructions
havebeencompletelyreadand
strictlyadheredto.
 Forfurthernotesonsafetyrefertoenclosed
Sheet.
 Makesuremachineisswitchedoffbefore
insertingpluginsocket.
 Alwaysinspectcableandplugbeforeusing
machine.Onlyhavedamagerepairedbya
qualiedprofessional.
 Themachinemustnotbedampandmustnot
beoperatedinawetenvironment.
 Cautionwithlonghair.Donotwearloose‑
ttingclothingwhileworking.
 Secureyourworkpiecewithclamps.
 Alwaysdirectpowercabletorearawayfrom
themachine.
 Whenscrewdriving,alwaysoperateinrst
gearandwithlowrpms.
 Usecautionwhenscrewdrivinglongscrews.
Dangerofinjuryduetoslippingoff.
 Alwaysensurethatyouhaveasecurefooting
whileworking.
 Watchoutfortheinitialtorquereactionofthe
drill,especiallywhendrillbitistight.
 Beforecarryingoutanyworkonthemachine
disconnectfrompowersupplybyremoving
plugfromsocket.
 When drilling with the impact activated use
hearing protection.Exposuretotheeffects
ofnoisemaycausehearingloss.
 Use the additional handle (additional
handles) if it is (they are) supplied with the
tool.Lossofcontrolmaycauseinjurepeople.
 When carrying out an activity where the
machining tool could touch hidden power
conductors or its own power cord, hold
the electromechanical tool by the insulated
surfaces.Touchingthemachiningtoolwith
a"live"electricalconductormaycausethe
exposedmetalpartsoftheelectromechanical
tooltobecome“live”andleadtoinjuryofthe
userbyelectricshock.
Intended Use
Themachineisintendedforimpactdrillingin
brick,concreteandstoneaswellasfordrilling
inwood,metal,ceramicsandplastics.Machines
withelectroniccontrolandright/leftrotationare
alsosuitableforscrewingandthread‑cutting.
Theuseraloneisresponsibleforanyliabilities
causedbyusageotherthanintended.
Starting and Operation
Incorrectoperationcanleadtodamageofthe
unit.Thereforealwaysobservethefollowing
recommendations:
‑ Sharpdrillbitsoptimizeperformancewhilst
minimizingwearonthemachine.
‑ Donotplacesuchloadsonthemachinethat
itceasestoturn.
‑ Changerotationaldirectiononlywhenthe
machineisnotmoving.
Ensurethatthevoltageofthepowersupply
matchestheinformationonthetypeplateofthe
powertool.Toolswitharatingof230Vcanalso
beconnectedtoa220V/240Vsupply.
Connecting the mains cable module
(Plug it)
Themachineisequippedwithaquick‑change
mainscablemodule(7).Bydisconnecting
themainscableandthemachine,bothcan
betransportedeasier.Insertthemainscable
module(7)intothesocket(14)ofthemachine
andsecurebyturningthesleeve(15)in
clockwisedirection.
Toundotheconnection,turnthesleeve(15)in
counterclockwisedirectionandpullthemains
cablemodule(7)fromthesocket(14).
Usethemainscablemoduleonlyfor
PROTOOLpowertools.Donotattemptto
operateothermachineswithit.
Auxiliary handle
Theenclosedauxiliaryhandle(12)mountson
thecollar(3).Itshouldalwaysbeusedtoensure
operatingsafety.Thedrillingdepthcanbeset
withthedepthstop(13).
Thepositionoftheauxiliaryhandleandthe
depthstopcanbechangedbyturningthe
handle.