Operation Manual

11
Notes on Safety
Thismachinecanonlybeoperated
safelywhentheoperating
instructionsandthepamphlet
containingthesafetyinstructions
havebeencompletelyreadand
strictlyadheredto.
 Forfurthernotesonsafetyrefertoenclosed
Sheet.
 Wearhearingprotection,especiallywhile
drillingwithimpact.Withoutsufcient
protectivedevices,thenoiselevelcanleadto
hearingimpairments.
 Usethesuppliedauxiliaryhandle.Lossof
controloverthemachinecanleadtoinjuries.
 Alwaysinspectcableandplugbeforeusing
machine.Onlyhavedamagerepairedbya
qualiedprofessional.
 Makesuremachineisswitchedoffbefore
insertingpluginsocket.
 Themachinemustnotbedampandmustnot
beoperatedinawetenvironment.
 Cautionwithlonghair.Donotwearloose‑
ttingclothingwhileworking.
 Secureyourworkpiecewithclamps.
 Alwaysdirectpowercabletorearawayfrom
themachine.
 Whenscrewdriving,alwaysoperateinrst
gearandwithlowrpms.
 Usecautionwhenscrewdrivinglongscrews.
Dangerofinjuryduetoslippingoff.
 Alwaysensurethatyouhaveasecurefooting
whileworking.
 Watchoutfortheinitialtorquereactionofthe
drill,especiallywhendrillbitistight.
 Beforecarryingoutanyworkonthemachine
disconnectfrompowersupplybyremoving
plugfromsocket.
 Thechuckkeyshouldalwaysbekeptinthe
holderprovidedonthecablesleeve.
 When drilling with the impact activated use
hearing protection.Exposuretotheeffects
ofnoisemaycausehearingloss.
 Use the additional handle (additional
handles) if it is (they are) supplied with the
tool.Lossofcontrolmaycauseinjurepeople.
 When carrying out an activity where the
machining tool could touch hidden power
conductors or its own power cord, hold
the electromechanical tool by the insulated
surfaces.Touchingthemachiningtoolwith
a"live"electricalconductormaycausethe
exposedmetalpartsoftheelectromechanical
tooltobecome“live”andleadtoinjuryofthe
userbyelectricshock.
Intended Use
Themachineisintendedforimpactdrillingin
brick,concreteandstoneaswellasfordrilling
inwood,metal,ceramicsandplastics.Machines
withelectroniccontrolandright/leftrotationare
alsosuitableforscrewingandthread‑cutting.
Theuseraloneisresponsibleforanyliabilities
causedbyusageotherthanintended.
Starting and Operation
Incorrectoperationcanleadtodamageofthe
unit.Thereforealwaysobservethefollowing
recommendations:
‑ Sharpdrillbitsoptimizeperformancewhilst
minimizingwearonthemachine.
‑ Donotplacesuchloadsonthemachinethat
itceasestoturn.
‑ Changerotationaldirectiononlywhenthe
machineisnotmoving.
Checkthattheplugistherighttypeforthe
socket
Ensurethatthevoltageofthepowersupply
matchestheinformationonthetypeplateofthe
powertool.Toolswitharatingof230Vcanalso
beconnectedtoa220V/230Vsupply.
Auxiliary handle
Theenclosedauxiliaryhandle(7)mountsonthe
collar(3).Itshouldalwaysbeusedtoensure
operatingsafety.Thedrillingdepthcanbeset
withthedepthstop(6).
Clamping a drill bit
Gear with chuck
Opendrillchuckenoughsothetoolcanbe
inserted.Insertthetoolandtightenall3bores
equallywiththechuckkey(16).
Quick Clamping Chuck
Opendrillchuckenoughsothetoolcanbe
inserted.
Turnthesleeveofthekeylessdrillchuckrmly
byhanduntiladistinct“click”isheard.The
keylessdrillchuckistherebyautomicallylocked.