™ ™ ™ 10637 Scripps Summit Ct., San Diego, CA 92131 P 858-536-5183 F 858-536-5191 www.protopaintball.com ©2004 DYE Precision, Inc. The stylized “proto” logo, the “p” logo, FUSE bolt and Hyper II are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc. Covered by one or more of the following U.S. Patents: 5,613,483; 5,881,707; 5,967,133; 6,035,843 and 6,474,326.
TABLE OF CONTENTS QUICK REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE 02 IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAGE 03 BOARD SETTINGS AND FUNCTIONS . . . . . . . . . . . . . . . . . . . .
QUICK REFERENCE - USING YOUR MARKER WARNING Air Supply - The MATRIX should be operated using air/nitrogen gas only. This air needs to be supplied to the Hyper2 in-line regulator at a regulated pressure of no more than 850 psi. The Hyper2 in-line regulator comes factory preset at 230psi. IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES Turning On Your MATRIX - The MATRIX’s power is controlled by two buttons. The top button turns the marker on and off, while the bottom button turns the eye on and off.
MATRIX BOARD - SETTINGS AND FUNCTIONS MATRIX BOARD - SETTINGS AND FUNCTIONS (CONTINUED) TURNING THE MATRIX ON AND OFF BOARD SETTINGS AND CONFIGURATION MODE To turn on the MATRIX, press and hold the upper button (see figure 1) until the LED light turns orange. The orange light indicates board bootup. After the bootup sequence, the LED will turn either RED (no ball) or GREEN (ball ready to fire). To turn the MATRIX off, press and hold the power button until the LED turns off.
MATRIX BOARD - SETTINGS AND FUNCTIONS (CONTINUED) Configuration Mode - The following settings can only be modified in configuration mode. To activate the configuration mode, turn your marker off and set DIP switch 2 to the on position. Next, turn your marker on. The 3-color LED cycles through all colors for one second to indicate that you have entered the configuration mode. To cycle through different settings, pull and release the trigger. Configuration mode has 3 settings that can be changed.
FUSE™ BOLT - ASSEMBLY AND MAINTENANCE FUSE™ BOLT - ASSEMBLY AND MAINTENANCE (CONTINUED) 1 2 BOLT MAINTENANCE 3 4 FUSE BOLT OPERATION To achieve top performance from your MATRIX, it is important to understand the basic operation of the MATRIX’s patented FUSE bolt system. This design consists of three sleeves threaded together to capture the only moving part of the system, the bolt.
LPR LPR (LOW PRESSURE REGULATOR) - ADJUSTMENTS AND MAINTENANCE (LOW PRESSURE REGULATOR) - ADJUSTMENTS AND MAINTENANCE CHANGING THE SEAL RETAINER 5 9 5 5 1 2 3 4 3 7 2 6 8 Screw Screw Screw Screw out LPR cap in front of the marker using a 1/4” Allen wrench. out LPR seal assembly (brass) using a 3/16” Allen wrench. in new LPR seal assembly. LPR cap in place securely.
HYPER 2 IN-LINE REGULATOR - ADJUSTMENTS AND MAINTENANCE 2 1 9 8 5 3 4 ANTI CHOP EYES 7 6 USAGE Carefully connect your air hose from your bottle or air system to the Hyper2 In-Line. The Hyper2 In-Line is set by the factory to approximately 230psi. This pressure should give you a velocity of approximately 285fps. ADJUSTMENTS The output pressure of the Hyper2 In-Line is adjusted by turning the brass seat housing. The seat housing screw is located up inside the bottom of the reg.
TRIGGER ADJUSTMENT MATRIX EXPLODED VIEW 1 17 ADJUSTING YOUR TRIGGER The trigger’s forward travel and over travel are fully adjustable so that the user can fine-tune the trigger to his or her exact liking. • Remove the grip frame from the body of the MATRIX. • As you pull the frame away from the body, take care so as not to damage the wires running between the two parts. Be careful not to lose the trigger spring.
TROUBLE SHOOTING GUIDE MATRIX WARRANTY INFORMATION WARRANTY MATRIX TROUBLE SHOOTING AIR LEAK BETWEEN THE FRAME AND BODY - AIR LEAK BETWEEN THE BODY AND REAR CAP First remove the frame and try to pinpoint the source of the leak: If it comes from the small hole under the LPR, you need to remove your LPR. The cause of the leak is either one of the #015 o-rings on the outside of the LPR or the #006 o-ring found inside the LPR (see page 10).
™ ™ ™ 10637 Scripps Summit Ct., San Diego, CA 92131 P 858-536-5183 F 858-536-5191 www.protopaintball.com ©2004 DYE Precision, Inc. The stylized “proto” logo, the “p” logo, FUSE bolt and Hyper II are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc. Covered by one or more of the following U.S. Patents: 5,613,483; 5,881,707; 5,967,133; 6,035,843 and 6,474,326.
