INTRODUCTION Thank you for your purchase of the Prodigy 66 charger from Protege R/C. The Protege Prodigy 66 Integrates the latest battery charging/discharging technology together with 4 blue back iit LCD screens, The 66 features integrated balance charging/discharging for 1 to 6 cell Lithium-Palmer (Lollipop. high voltage Lithium Polymer (HV), Lithium-Ferric (Life, The Prodigy 610 also supports charging and discharging nickel-cadmium (Ni Cd) and nick-metal hydroxide (NIGH) batteries.
1. AC Input 3. Ch1 Balance Part 5. Discommode 7. Inc. 9. LCD Screen 11. Ch2 Balance Port 13. DC Input INTRODUCTION 1041 12 13 14 2. Ch1 Output 4, Chl Temperature Sensor Port 6. Dec, 8, Start/Enter 10. Ch2 Temperature Sensor Port 12. Ch2 Output 14.
WARNING AND SAFETY NOTES These warnings and safety notes sre particularly itinerant. Please folio the Instructions for maximum safety; otherwise the charger and the battery can be damaged or at worst i can cause re u WERE Fee Band AA Never leave the charger unattended when It Is connected to ts power supply. if any malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the ope radon manual. A A Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration.
WARNING AND SAFETY NOTES «A battery pack, which consists of different types of cells {including different manufacturers). «A battery that is already fully charged or just slightly discharged. «Non-rechargeable batteries (Explosion hazard), «A faulty or damaged battery. A battery fitted with an Integral charge circuit or a protection circuit. « Batteries Installed In a device or which are electrically inked to other components.
WARNING AND SAFETY NOTES A A charging During charge process, a specie quantity of electrical energy Is fed Into the battery. Tne charge quantity Is calculated by multiplying charge current by charge time. The maximum permissive charge current varies depending on the battery ype or its performance, and can be found In the information oy the battery manufacturer, Only batteries that are expressly stated to be capacities of quick char are allowed fo be charged at rates higher than the standard charge current.
WARNING AND SAFETY NOTES hd Discharging The main purpose of discharging is to clean residual capacity of the battery, or to reduce the battery voltage ta a defined level. The same attention should be paid to the discharging process as the charging process. The final discharge voltage should be set up correctly to avoid deep discharging. Lithium batteries can not be discharged to lower than the minim voltage or ft will cause a rapid loss of capacity or natal allure.
MAIN FEATURES Dual Power Input The power source can be 11-18 DC input, It can be powered up at any place with a 12V car battery or 110V or 220V AC Input. The power supply Is built In and users could connect the AC Power cord to the man AC socket directly. The AC Input voltage Is 110 or 220V so that the users could use this charger all over the world and font need to worry about any damage caused by improper input voltage.
BASIN FEATURES Terminal voltage Control (TVG) The charger allows user to set the charge/discharge and voyage. Cap achy Limit The charging capacity 's always calculated ss the charging current multiplied by time, If the charging capacity exceeds the mit, the process wil be peregrinated automatically when you set the madman value. Processing Time Limit You can lase mit the maximum process time to avoid any possible battery deduct or cell damage.
CHARGER SETUP Here are the detailed procedures to make the charger work. all the streets and operations wi take Balance Lip-CHARGE program for example. Source “The 610 comes with the bulk in switching power supply. You can connect the AC parer cord directly to the main AC socket {110¥ or 220V AC) ar attaching directly to 12¥ car batteries, iis erotically Important that you use a fully charged 13.8V car battery.
CHARGER SETUP Explanation of Buttons BAT (bee. Ine, > { start ) “Bart Type." button It is used to stop the process or go escape back to the previous step. “Dec.” button It Is used to go through the menus and decrease the parameter value. “In” button It Is used to go through the menus and Increase the parameter value. “Start” button It is used to enter parameter or start program.
LITHIUM BATTERY (LiPo/LiHV/LiFe/Lilon) PROGRAM WARNING: BEFORE YOU BEGIN CHARGING YOUR BATTERY, MAKE SURE YOU HAVE READ AND UNDERSTAND ALL OF THE WARNINGS AND SAFETY INFORMATION CONTAINED ON PAGES: 36 DURING CHARGING/DISCHARGING, THE BATTERY SHOULD BE PLACED IN A FIRE PROOF CONTAINER OR FIRE SAFE LIP BAG AND AWAY FROM ALL FLAMMABLE MATERIALS. NEVER LEAVE BATTERY OR CHARGER UNATTENDED. To determine the correct charge rate and cell count, please refer to the Instructions Included with your battery.
LITHIUM BATTERY (LiPo/LiHV/LiFe/Lilon) PROGRAM WARNING: BEFORE YOU BEGIN CHARGING YOUR BATTERY, MAKE SURE YOU HAVE READ AND UNDERSTAND ALL OF THE WARNINGS AND SAFETY INFORMATION CONTAINED ON PAGES: 36 DURING CHARGING/DISCHARGING, THE BATTERY SHOULD BE PLACED IN AFIRE PROOF CONTAINER OR FIRE SAFE LIP BAG AND AWAY FROM ALL FLAMMABLE MATERIALS. NEVER LEAVE BATTERY OR CHARGER UNATTENDED. Continued. LID BLE 45 4. After confirming all presets, press “START” for 2 seconds = S88EnRk 3.
PROGRAMMING PROCESS LITHIUM VARIOUS INFORMATION DURING THE CHARGE/DISCHARGE PROCESS Press “Inc. Tad “Dec.” during the charging or discharging process to view further pertinent information an the LED screen, eld ges) § Derby § peer Certs Di SE § bevy Sadat Tom w pr § peck Wea § peck pr pec Imposer Unitas ®78 ine, ® team Zam Ga Dial Program Stop During the charging process, press "Bart Type ta stp the charging process. Program Finished Charger wii alarm once program finished.
DISCHARGING PROCESS WARNING: BEFORE YOU BEGIN DISCHARGING YOUR BATTERY, MAKE SURE YOU HAVE READ AND UNDERSTAND ALL OF THE WARNINGS AND SAFETY INFORMATION CONTAINED ON PAGES: 3 6 DURING CHARGING/DISCHARGING, THE BATTERY SHOULD BE PLACED IN AFIRE PROOF CONTAINER OR FIRE SAFE LIP BAG AND AWAY FROM ALL FLAMMABLE MATERIALS, NEVER LEAVE BATTERY OR CHARGER UNATTENDED, Schiaparelli Program Warning: Ensure to set the correct end voltage, or It may over.discharge the battery, please ses the table on pga.
STORAGE PROCESS WARNING: BEFORE YOU BEGIN STORAGE FUNCTION, MAKE SURE YOU HAVE READ AND UNDERSTAND ALL OF THE WARNINGS AND SAFETY INFORMATION CONTAINED ON PAGES: 3 6 DURING CHARGING/DISCHARGING, THE BATTERY SHOULD BE PLACED IN AFIRE PROOF CONTAINER OR FIRE SAFE LIP BAG AND AWAY FROM ALL FLAMMABLE MATERIALS. NEVER LEAVE BATTERY OR CHARGER UNATTENDED. Storage Program “STORAGE” Is a function which Is specialized for Lithium battery storage, ts operation Is sear as the discharge program.
PROGRAMMING NIGH, NICE and Pb PROGRAM SELECT Once you power on the charger, press the BAT/ iH Buttery ESC key. This will shift you down to the “Program Gait: Select” menus, Navigate with the BAT TYPESCRIPT and < DEC keys until you reach your desired NIGH or Nice battery type (be sure to select the correct battery type!). Then press the Enter/Start key. “CEC THIGH CHARGE Han 1.
PROGRAMMING NIGH, NICE and Pb The screen displays the state of the started process. To forcibly stop the recess press the BAT TYPESCRIPT key. Description of displays: £3 battery type; £3 operation mode CHG=Charge, Discharged. CHG —» CHG or CHG—» CHG. Pachyderm 2 mode; £} elapsed time; £ charge/discharge HH, Cries he" currant of the battery; €} battery voltage; © ; capacity of charge/discharge.
BATTERY MEMORY PROFILE PROCESS Battery Memory “The charger can store up 1 10 different charger discharge profiles for your convenience, and the stored profiles can be recalled quickly without having to go through the setup process. Battery Ornery Set Ever into this program | Herero swe | Press “Inc.
SYSTEM SETTINGS The Prodigy 66 will aerate with the default values when iris powered on for the first de. The screen displays below show the system settings In sequence and the user can change the parameter values on each screen. ‘When you want to change the parameter value, press the “Start” button to make it blink, then change the value using the ** or “* buttons. The values will be stared by pressing the “Start” button once more.
SYSTEM SETTINGS Description CHIFFON {10720 Mi) When you start a charge prices, hie internal safety timer automatically starts] running at the same time. Lis diagrammed to preen Overcharging, If the battery proves 10 be faulty or I the semi nation cultured cannot detect the full battery. The value of the safety timer should be generous enough to allow full charging of the battery. (130-9890 mA) “This chats the maximum charge capacity thallium be supplied fa the battery during charge.
ERROR MESSAGE REVERSE POLARITY CONNECTION BRAE, SHORT ERROR INPUT LDL ERR BATTERY CHECK Lo TRUDGE BATTERY CHECK HIGH VOLTAGE. BATTERY VOLTAGE CELL LOW LOL BATTERY TRAGEDY CELL HIGH U0L BATTERY VOL ERR CELL CON MEET TEMP GRUE ERR $1 incorrect polarity connected. Charger and battery connection is wrong. nut rhos drat nut voltage less than required value Battery total voltage Is lower than setting value, please check the cell court.
CERTIFICATION COMPLIANCE INFORMATION FOR THE EUROPEAN UNION European Compliance Information Declaration of Conformity The object of declaration described above is In conformity with the requirements of the specifications listed below, following the provisions of the European EMC Directive 2004/108/EC. Product(s): Battery balance charger tam Numerous: PKT-8517 Instructions for disposal of WERE by users In the European Union This product must not be diseased of with other waste.
WARRANTY & SERVICE Thank you for purchasing the Prate RAC Prodigy 66 AC/DC Battery Charger. We will do our best to provide you with comprehensive after sale service and protect Your rights and Interests, Protege R/C guarantees this Item to be free of defects In materials and workmanship for (1) year after the original purchase date.
