DUO TOUCH AC/DC PTK-8519 Instruction manual
TABLE OF CONTENTS INTRODUCTION.............................................................................................. 01 SPECIFICATIONS............................................................................................. 03 MAIN FEATURES............................................................................................. 04 WARNING AND SAFETY NOTES.................................................................... 06 PROGRAM FLOW CHART.........................................
INTRODUCTION These operating instructions are designed to ensure that you quickly become familiar with the charger and its functions. It is therefore important that you read through the Operating instructions, Warning and Safety Notes before you attempt to use your new charger for the first time. The ProTek Prodigy 625 integrates battery technology together with touch operated system. Each channel is equipped with a 128x64 pixel resistive touch screen, which plays a very important role in the entire system.
INTRODUCTION Se yo t the it u co rig ma nn ht y ect AC cau se the input exppo vo loswer lta ion co ge ! rd, be oth for erwe ise VO LT A G E SE LE C TO R A C IN P U T 1 6 ER USB POW 5V/2. 1A 54 3 2 1 Te m p 1 2 3 . 4 56 7 8 9 10 11 UT INP DC -18 V 11 Do n ot cov er US B PO 5V/ WE 2 .1A R 2 654 Tem 32 1 p. 12 13 14 15 16 1. 110V or 220V Switch 9. USB 2. Power Switch 10. CH2 Touch Screen 3. AC Input 11. CH2 Firmware Upgrade Port 4. CH1 Output 12.
SPECIFICATIONS ● AC Input Voltage: 110V OR 220V ● DC Input Voltage: 11-18V ● Control: Touch ● Display Type: LCD Touch Resistive Screen x2 ● Backlight: Adjustible (Off-100%) ● Cooling System: Cooling Fan ● Dimension: 240 x200 x68mm ● Weight: 1725g ● Charge Current: 25.0A x2 ● Safety Timer: 1-720min or Turn Off ● Charge Power: Max. 200W x2 ● Discharge current: 5.0A x2 ● Balance Current: 400mA/cell ● Discharge Power: Max.
MAIN FEATURES Touch System With the graphic touch controlled interface, the resistive touch LCD screen intuitively displays every charging status & information, which makes the operating procedures very easy. Users can enjoy a more convenient and comfortable “touch” experience.
MAIN FEATURES Memory Preset The charger can store up to 20 different charge/discharge profiles for your convenience. You can keep the data pertaining to the program setting of the battery of continuous charging or discharging. Users can call out these profiles at any time without any special program setting. Terminal Voltage Control (TVC) The charger allows users to set the charge/discharge and voltage. Capacity Limit The charging capacity is always calculated as the charging current multiplied by time.
WARNING AND SAFETY NOTES These warnings and safety notes are particularly important. Please follow the instructions for maximum safety; otherwise the charger and the battery can be damaged or at worst it can cause a fire or injury to the user. Never leave the charger unattended when it is connected to its power supply. If any malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the operating manual. Always use a LiPo Safe bag or a non flammable non conductive containment box while in use.
WARNING AND SAFETY NOTES Never attempt to charge or discharge the following types of batteries ● A battery pack, which consists of different types of cells (including different manufacturers). ● A battery that is already fully charged or just slightly discharged. ● Non-rechargeable batteries (Explosion hazard). ● A faulty or damaged battery. ● A battery fitted with an integral charge circuit or a protection circuit. ● Batteries installed in a device or which are electrically linked to other components.
WARNING AND SAFETY NOTES Charging During charge process, a specific quantity of electrical energy is fed into the battery. The charge quantity is calculated by multiplying charge current by charge time. The maximum permissible charge current varies depending on the battery type or its performance, and can be found in the information by the battery manufacturer. Only batteries that are expressly stated to be capable of quick charge are allowed to be charged at rates higher than the standard charge current.
PROGRAM FLOW CHART LiPo LiIon LiF Charg S Charg Charg LiHv Charg Discharg t S S S 14 8 5000 4 14 8 5000 4 14 8 5000 4 14 8 5000 4 14.8V 4S 5000mAh LiIon t t LiIon 14.8V 4S 5000mAh Discharg LiF t Discharg 14.8V 4S 5000mAh 14.8V 4S 5000mAh LiF 14.8V 4S 5000mAh LiHv Discharg 14.8V 4S 5000mAh LiHv 14.8V 4S 5000mAh 14.8V 4S 5000mAh CYCLE Charg 00 Discharg 5000 1 0 CYCLE Cd Charg 00 Cd Discharg Cd Cd 5000 1 0 -1.00V 0.1A LiPo 6S C=10.
OPERATION DESCRIPTION Depending on what battery type, the operating programs are different for each. Battery type LiPo Lilon LiFe LiHV NiMH NiCd Operation Program Description Balance Charge This charging mode is for charging LiPo/ LiFe/ Lilon/ LiHV battery in normal mode. Storage This mode will either charge or discharge LiPo/ LiFe/ Lilon/ LiHV batteries to the appropriate voltage for storage. Discharge This mode is for discharging LiPo /LiFe /Lilon /LiHV battery.
OPERATION PROGRAM 1. Touch Screen Operation 1). Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu screens. 2). Press the action at the button of the LCD Touch Screen to enter that menu. 3). Press a parameter to highlight that parameter. 4). Press the Up and Down Arrows to edit the parameter. 5). Press “Enter” for more than 2 seconds to save the parameter and start working. 6).
OPERATION PROGRAM 2. Connection The following describes the action process of the charger, using a lithium polymer battery charging program as an example. 1) Connecting power You can attach the 625 directly to a 11-18V output power supply via the XT60 input cable. 2) Connecting The Battery Important!!! Before connecting a battery it is absolutely essential to check one last time that you have set the parameters correctly.
OPERATION PROGRAM 3. Charge program In this program, user can set the cell count, battery pack voltage, battery capacity, charge current, end voltage and charge mode. Press Enter for more than 2 seconds to start charging. Notice: According to the battery capacity setting, charger will automatically set the charge current at a rate of 1C.
OPERATION PROGRAM Go to previous screen Input voltage LiPo 4S CHG 10 End voltage Internal temperature Safety timer Cut-off capacity 2). View cell voltage and cell resistance 1 2 3 4 5 6 20m 15m 15m 20m -- m -- m Back to previous screen 3). View voltage curve graph during charging Data LiPo Graph 117 33 Back to previous screen 4). Stop process finished Press the “STOP” button to stop charging. 5). Process finished Charger will alarm once program finished.
OPERATION PROGRAM 4. Discharge program In this program, user can set the cell count, battery capacity, discharge current and end voltage. Attention: Set the correct discharge end voltage, or it will cause over discharge and damage the battery. Set cell count and pack voltage Discharg Set battery capacity 14.8V 4S 5000mAh Set discharge current Set end voltage Press Enter>2S=Start Elapsed time Go to next screen 1).
OPERATION PROGRAM Go to previous screen Input voltage LiPo 4S DCHG 10 End voltage Internal temperature Safety timer Cut-off capacity 2).View cell voltage and cell resistance 1 2 3 4 5 6 20m 15m 15m 20m -- m -- m Back to previous screen 3).View voltage curve graph during discharging Data LiPo Graph 117 33 Back to previous screen 4).Stop process finished Press the “STOP” button to stop charging. 5).Process finished Charger will alarm once program finished.
OPERATION PROGRAM 5. Storage Program for Lithium Battery “STORAGE” is a function which is specialized for Lithium battery storage, its operation is same as the discharge program. To store your lithium battery for any period of time and extend the life of the battery this function is critcal. For different battery types, the end voltages are different, LiPo:3.7V, LiHV:3.85V, LiFe:3.4V, Lilon:3.6V.
OPERATION PROGRAM 6. Battery Memory The charger can store up to 20 different charge/discharge profiles for your convenience, and the stored profiles can be recalled quickly without having to go through the setup process. 1). Save When you finish setting the charging/ discharging/storage parameters, please press ESC to return to the main menu screen, and go to MEMORY screen. LiPo 6S C=10.0A Press SAVE, the parameters you just entered will be saved. LiPo 6S C=10.0A 2).
OPERATION PROGRAM 7. Data view With this program, user can check the battery cell voltage, internal resistance, input voltage, output voltage, inner temperature and external temperature. Please connect the battery to charger output port (both main output and balance port).
OPERATION PROGRAM 8. Lithium battery balancer This function is for unbalanced lithium battery packs, set the correct battery type when using this program, or it will damage the battery. The equalizer circuit will work independently and reduce the voltage difference to below 0.02V, which can prolong the life of the battery and reduce risks due to over discharge. CAUTION: Please check the battery type and settings carefully, or it may damage the battery.
OPERATION PROGRAM 9. Digital Power In this mode, the charger can provide a output power of DC3.0V-24V for other device. Set output voltage Set output current Set output power Press Enter>2S=Start Real time output voltage Real time output current Real time output power A0: It shows the last setting here, press Start for more than 2 seconds to start if no changes are needed.
OPERATION PROGRAM 10. Forming Charge For NiMH/NiCd batteries that have been stored for a long time, the charger will charge the battery pack by a low current for a long time, which can depolarize and reactive battery.
SYSTEM SETTING Notice: Please set the parameters in Setup menu when charger is powered on for the first time. This charger can recognize battery cell count automatically. It has a pre-charge function which can reactivate the slightly over discharged cell. Users can set the pre-charge time (normally 2 minutes) in the menu. The more battery capacity, the more time is needed. Attention: In the normal charge mode, always turn off the precharge program.
SYSTEM SETTING Go to next screen Set safety timer:OFF/1-720min Set screen brightness: OFF/10%-100% Set melody Button sound:ON/OFF Set buzzer volume:ON/OFF Go to next screen Set balance force trigger voltage, for LiPo/LiFe/LiIon/LiHV battery ONLY. -1.00V 0.1A Set full force Set discharge mode CC or CV, for LiPo/LiFe/LiIon/LiHV/Pb battery ONLY.
SYSTEM SETTING Notice: When in this program, Pb battery is recommended to connect to the charger input port, DO NOT use NiMH/NiCd as a “battery power”. Users can set the user name and it will be displayed once the charger is powered on. SER NAME SETUP - ABCDEFGHI J K L M. NOPQRSTU VWX Y Z, 0 1 2 3 4 5 6 7 8 9 + - -USER_NAME x Factory reset: This operation will delete all your personal data, and reset all settings to the manufacturer default settings. DO NOT use it unless you are sure it is necessary.
ERROR MESSAGE Incorrect polarity connected Process interrupted Output short circuit Input voltage error Charger fault Battery total voltage is lower than setting value, please check the cell count. Battery total voltage is higher than setting value, please check the cell count. Voltage of one cell in the battery pack is too low.
ERROR MESSAGE Voltage of one cell in the battery pack is too high. The battery balance connection is wrong. Please check the connector and cable. Temperature too high, please check the temperature sensor and take cooling measures.
AUTHENTICATION INFORMATION PTK-8519 28
Warranty 625 Duo Touch 29
