PRT-WX-DIN Using Protege WX Installation and Programming Manual
The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited.
Contents Introduction ___________________________________________________________________ 6 Operation Mode _______________________________________________________________________ 6 What This Manual Covers ______________________________________________________________ 6 System Expansion and Capacities _______________________________________________________ 6 Technical Specifications ________________________________________________________________ 7 System Installation and Setup _____________________________
Creating an Area ___________________________________________________________________ 29 Pulse Times _______________________________________________________________________ 30 Configuring Schedules and Holidays ____________________________________________________ 31 Creating Holiday Groups ____________________________________________________________ 31 Creating Schedules ________________________________________________________________ 32 Schedules and Multiple Time Spans _____________________________________
Daylight Savings ___________________________________________________________________ 85 Schedules ________________________________________________________________________ 86 Expanders ___________________________________________________________________________ 88 Keypads __________________________________________________________________________ 88 Analog Expanders _________________________________________________________________ 91 Input Expanders _____________________________________________________________
Introduction Protege WX is an all-in-one, web-based, cross-platform system that gives you a fully functional access control and intrusion detection solution in a fraction of the time of conventional software. With no software to install, setup is quick and simple. Connect the Controller and system components, then open a web browser to launch the intuitive wizard-driven interface which guides you through the process of configuring your system.
Technical Specifications The following specifications are important and vital to the correct operation of the Controller. Failure to adhere to the specifications will result in any warranty or guarantee that was provided becoming null and void. Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting the ICT website (http://www.incontrol.co.
System Installation and Setup The following section outlines what you need to do to install your Protege WX system. The process is broken into the following steps. 1. Mount the Controller (see page 8) 2. Connect the Power Supply (see page 9) 3. Connect any networked modules (see page 12) (such as Reader Expanders and Keypad units) 4. Connect Card Readers (see page 13) 5. Connect Door Contacts (see page 15) 6. Connect Lock Outputs (see page 16) 7.
Connect the Power Supply Power is supplied to the Controller by a 12V DC power supply connected to the N+ and N- terminals. The Controller does not contain internal regulation or isolation and we recommend using an ICT PRT-PSU-DIN for this purpose, although any clean 12V DC supply is suitable. Warning: Termination of wiring to the Controller while power is applied or the battery is connected may cause serious damage to the unit and will VOID ALL WARRANTIES OR GUARANTEES.
PRT-CTRL-DIN N+ N- NA PRT-PSU-DIN NB V1+ V1+ V1+ V1+ V1+ V1+ V- V- V- V- V- V- To other modules on network N+ N- NA NB L B- B+ Gel Cell Backup Battery N Mains Input + Example Power Supply Connection - PRT-PSU-DIN-4A In a small installation this same power supply can be used to supply the module network as well, so long as the maximum load of the power supply is not exceeded.
Cabinet Tamper Switch The enclosure tamper input signals to the monitoring station or remote computer that the enclosure has been opened. The tamper input switch should be mounted into the steel bracket provided and connected to the tamper connection terminal and the V- terminal as shown below. The tamper input opens and closes trouble input AExxx:01 on the Power Supply.
Connect Networked Modules The Controller incorporates encrypted RS-485 communications technology for connecting networked modules.
End of Line (EOL) Resistors The 330 Ohm EOL (End of Line) resistor provided in the accessory bag must be inserted between the NA and NB terminals of the first and last modules on the RS-485 network. These are the modules physically located at the ends of the RS-485 network cabling.
Standard Card Reader Connection The following diagram shows the connection of a standard Wiegand Reader with the Controller controlling an access door in entry or exit mode (2 doors, 2 readers).
Connect Door Contacts The Controller allows the connection of up to 4 contacts for monitoring and controlling access control doors. Each input on the Controller can be used for either the door function that is automatically assigned or as a normal input on the system. N.C. Input Contact 1K 1K REN Input Bond Sense 1K 1K Z4 V- N.O. Input Contact Z3 N.C. Input Contact Z2 1K 1K VZ1 REX Input V- V+ Door Contact 1K 1K N.O.
Connect Lock Outputs The Controller provides a connection for an electric strike lock with full monitoring of the lock circuit for tamper and over current/fuse blown conditions. V+ V- + NO 1N4007 Diode C NC - NO C 12VDC Electric Locking Device NC + - Power Supply for Locking Devices Max 30VDC Typical Lock Output Connection i The Bell output current must not exceed 1.1A or electronic shutdown will be engaged.
The default IP address is set to a static IP address of 192.168.1.2 with a subnet mask of 255.255.255.0. These IP address settings are commonly used for internal networks. The IP address of the Controller can be configured using the LCD Keypad terminal or via the built in web interface. i Installing the Controller on an active network requires knowledge of the configuration and structure for the network.
i Inputs 1-4 (Door 1) and 5-8 (Door 2) can operate as either general purpose inputs or as onboard reader inputs. If used as general purpose inputs you must ensure that they are not defined in the onboard reader set up. Each input can use a different configuration. Z4 V- Z3 Z2 V- Z1 N.C Input Contact V- V+ When using the No Resistor configuration, the Controller only monitors the opened and closed state of the connected input device generating the alarm and seal conditions.
Outputs The Controller has 7 onboard outputs which can be used to activate sirens, bells, warning devices, control lighting and doors. The first output on the Controller has a special hardware design that allows it to monitor for fault conditions and is ideally suited to driving sirens or warning devices. Bell/Siren Output The + and - terminals of the Bell output (CP001:01) are used to power bells, sirens or any devices that require a steady voltage output.
Warning: The Relay outputs can switch to a maximum capacity of 7A. Exceeding this amount will damage the output. Reader Outputs If readers are not attached to the reader ports, then the Reader 1 L1 and BZ, and the Reader 2 L1 and BZ outputs can be used as general purpose outputs. These can be controlled by assigning the RDxxxGreen R1, RDxxx Beeper R1, RDxxxGreen R2 and RDxxx Beeper R2 outputs of whichever reader module has been configured as the onboard reader module.
Getting Started This section outlines the process for logging in for the first time and walks you through the Protege WX Configuration Wizard. Logging In for the First Time 1. Open a web browser and enter the IP address 192.168.1.2 The Login window is displayed. 2. Enter the default operator login of admin with the password admin. For security reasons, this password should be changed (see page 104) before deployment. 3. Click Login. Set the Controller Time 1. Navigate to Scheduling | Time 2.
Understanding the Defaults To simplify things and make programming your site as easy as possible, Protege WX includes a number of default settings. These can be used 'as is' for quick and simple deployment, or adapted to suit your needs. Either way, it helps if you understand what the defaults are and what they do. You'll find the names describe them pretty well. Users: You'll find three users by default - Installer, Master, and User (Demo).
Using the Protege WX Wizards Once logged in, the Home Page is displayed. Select the Wizards menu at the top of the page to run through each of the wizards that will guide you through the initial setup, giving you a fully functional access control and intrusion detection solution in no time. 1. Expanders Wizard 2. Access Control Wizard 3. Security Wizard 4.
2. Click Step 2- Auto Detection to continue. The wizard automatically detects the modules and displays them here: 3. Each module is assigned a name automatically. These can be renamed as required to provide a more meaningful name for easier identification. 4. Click Save and Return to Menu to finish. Progress is shown as the Controller is programmed and the corresponding inputs, outputs, and trouble inputs are created. Once complete, you are returned to the Home page.
3. Click Save and Continue to proceed to step 2. 4. Select the Unlock Schedule if required then click Save and Return to Menu. Progress is shown as the Doors are created. Once finished, you are returned to the Home page. Security The Security Wizard allows you to configure the Areas in your system, the Inputs that are used to trigger events, and setup basic offsite monitoring services. This step disarms any areas that are currently armed, and will prompt you to confirm the action. 1.
2. Click Save and Continue to proceed to the next step. The wizard lists each of the Inputs in your system. 26 Rename each Input to provide a more meaningful description for easier identification. Select the End of Line Resistors according to those used when wiring the EOL configuration. Select the Input Type to defines how an input will operate in an area. For example, Delay will go into entry delay when triggered, whereas Instant will activate immediately.
3. Click Save and Continue to proceed and configure Offsite Monitoring. All modules will be restarted automatically. 4. If using PSTN Monitoring, enter the Dialler information: Set the Primary Phone Number of the monitoring station Set the Backup Phone Number of the monitoring station. This number will be dialed if a connection with the station cannot be made on the primary phone number. Enter the Client Code (or account number).
Users The Users Wizard enables you to quickly create new Users, and define which Areas and Doors they are able to access. 1. For each user, enter the name, PIN, and card details. Select the Area(s) and Door(s) you wish to grant them access to, then click Add User. 2. Repeat until you have added all the users you need.
Configuring Additional Areas Areas allow for the Protege system to be divided up into separate sections (alarm areas or partitions) that will be monitored for intrusion or other purposes. There is one placeholder Area that is created by default which you can configure using the Security wizard to fit your needs. If you require additional areas, you can either create these before running the wizard then use the wizard to configure them, or create and configure them later. Creating an Area 1.
Pulse Times Pulse times allow an output or group of outputs to be pulsed for the duration of an area state. For example, the keypad beeper can be used to make short beeps for an exit delay, then a long continuous beep for entry delay. Pulse times are measured in tenths of a second or 100ms. A pulse time of 10 equates to 1 second. Setting the Pulse On to 1 and the Pulse Off to 9 provides a short pulse (such as a short beep or flash) every second.
Configuring Schedules and Holidays Schedules are defined timeframes that enable a function or access level to operate only within certain scheduled periods. They can be used to control when a user can gain access to things, to unlock doors automatically, to arm or disarm areas at certain times or days, and turn thing on and off or change the way they behave at certain times of day.
Creating Schedules 1. Navigate to Scheduling | Schedules and click Add 2. Enter a Name for the schedule 3. Enter the start and end time for each period and select the days you wish the schedule to operate on by enabling the appropriate boxes. Notice how the Graphics View updates to show when the schedule will be valid. 4. For each period, choose the Holiday Mode to define how the schedule will operate during a holiday period.
5. If required, select the Options tab to set the Qualify Output. This allows you to qualify the schedule based on the state of an output. In this example, this schedule will only ever become valid if all the other conditions of the schedule are met, and the KP1 Red LED output is off. Consider a schedule that has been programmed to unlock the front door of a retail shop. By configuring a qualify output, the front door would unlock at opening time only if the alarm has been unset.
Shorter Hours on a Holiday In some installations, especially retail, a schedule must still operate on a holiday, but may do so for shorter hours. In this example, the schedule will be valid from 9am to 5pm, Monday to Friday on normal days. If the day is a holiday, the schedule will only be valid from 10am to 4pm. Multiple Periods in a Single Day Another example would be where there are multiple periods required in a single day.
Overlapping Periods Where overlapping periods are present, the schedule will take the sum of all periods. In this example, Wednesday has two periods that overlap. The two periods are combined, and as a result, the schedule will be valid from 9am to 3pm on Wednesday. Rules for Schedules and Holidays If you program times and days in to a schedule, but don't do anything else, then the schedule will always operate.
Monitoring Your System The All Events page and Status Lists provide functions for monitoring your site. The LED indicators on the Controller and Power Supply are useful for diagnosing faults and conditions. Viewing Events The All Events window provides a live and historic view of all events. Use the Previous and Next buttons to navigate through the pages. Click Live View to return to the real time display.
Each status list also enable you to manually control the items from the web interface. For example, you can use the Door Status List to lock and unlock doors, or use the Area Status List to arm and disarm areas. LED Indicators All DIN Rail modules included comprehensive front panel diagnostic indicators that can assist in diagnosing faults and conditions. In some cases an indicator may have multiple meanings depending on the status indicator display at the time.
Status Indicator The Status indicator displays the status of the Controller. State Description Flashing (green) at 1 second intervals The Controller is operating normally Fault Indicator The Fault indicator is lit any time the Controller is operating in a non-standard mode. During normal operation the fault indicator is off.
Bell Indicator The Bell indicator shows the status of the bell output and the over current or circuit fault conditions. State Description Off Bell is connected, output is OFF On (green) Bell is ON Single (green) flash Bell is ON, the circuit is in over current protection Two (green) flashes Bell is OFF, the circuit to the siren/bell is cut, damaged or tampered Relay Indicators The Relay 1 and Relay 2 indicators show the status of the lock output relay.
Power Supply (PRT-PSU-DIN-2A) Power Indicator The Power indicator is lit whenever the correct module input voltage is applied across the AC input terminals. State Description Constantly on Correct module input voltage applied Constantly off Incorrect module input voltage applied Status Indicator The Status indicator displays module status of the Power Supply.
V1 Output/V2 Output Indicators The V1 Output and V2 Output indicators will show the status of the 12VDC output. State Description Constantly on 12VDC output operating OK Constantly off 12VDC output failure Battery Indicator The Battery indicator will show the status of the backup battery.
Error Code Display The following table is only valid if the FAULT indicator is CONSTANTLY ON and the STATUS indicator is FLASHING RED. If the fault indicator is FLASHING the module requires a firmware update or is currently in firmware update mode. The status indicator will FLASH RED with the error code number. The error code number is shown with a 250ms ON and OFF period (duty cycle) with a delay of 1.5 seconds between each display cycle.
Trouble Inputs Trouble inputs are used to monitor the status of the Controller and in most cases are not physically connected to an external input. These can then be used to report a message to a monitoring station, remote computer, keypad or siren.
Property Reference Guide This section describes each of the properties available when programming your system, and what they do. Users The Users menu contains the various functions for working with and configuring users (sometimes referred to as cardholders), and defining the access they have within a site.
Start / End Times Start Date: Optional setting enabling you to set a start date for the user. For example, an employee that will start work on a specific date. Expiry Date: Optional setting enabling you to set an expiry date for the user. For example, a contractor who will finish on a specific date. Users | Access Defines the access level(s) for the user.
User Can Acknowledge Alarm Memory: When enabled the user is able to acknowledge alarm memory. Alarm memory is stored for each area and will record the last 4 activations. The alarm memory can be viewed from MENU 5 on the keypad and must be enabled to allow acknowledgment to occur. This setting can be overridden by the same option in the menu group.
Access Levels | Doors Defines the doors that the user has access to, and the schedule that is used. By default, the schedule is set to Always, meaning access to the defined doors is permitted at all times. Assigning another schedule will restrict access to the door for the period set in the schedule. For example, limiting access to an office so it may only be entered during office hours. Access Levels | Door Groups Defines the Door Groups that the user has access to, and the schedule that is used.
Monitoring Functions for monitoring your site are contained under the Monitoring menu.
Doors Doors are used for the control of access by users or to monitor and control the flow of people in to an area. Name: The name of the door. Setup Door Type: The door type selection allows the door to function in different modes. These modes require the user to present specific credentials for example a card, card and pin, card or pin and pin only. By using a door type these can be scheduled dependent on the time of day allowing different security credentials to be used.
Doors | Outputs Lock Output: Lock Output/Output Group: You can assign an output or output group that controls the physical electric lock for the door. This is typically the lock control output on the reader expander that is being used to control the door. Lock Activation Time: The unlock time determines how long the lock that controls the door will remain unlocked for when a user accesses the door.
Left Open Alarm Pulse On Time: The left open alarm pulse on time is used to make the output pulse on and off when activated. The value entered here must be greater than 0 and is in increments of 100ms. For example setting 10 will pulse the unit on for 1 second and then off for the programmed time set in the pulse off section. Left Open Alarm Pulse Off Time: The left open alarm pulse off time is used to make the output pulse on and off when activated.
Door Options Always Check Unlock Schedule: When enabled the door will revalidate the unlock schedule that it is assigned each minute. This will prevent the door from being controlled and locked when it should be unlocked. This option also prevents schedule and area control from operating correctly and if enabled will prevent the follow inside and follow outside area status from operating. Setting this option will allow the prevent unlock on arming and normal scheduling operations to occur.
Doors | Advanced Options Advanced Options Lock out REX When Inside Area Armed: When enabled the door will deny a request to exit when the inside area has been armed to prevent egress from an armed area. Deny Entry if Inside Area is Armed: When enabled the door will deny any entry if the inside area is armed. Deny Exit if Outside Area is Armed: When enabled the door will prevent any exit if the outside area is armed.
Door Groups Door groups are used to define which doors a user will be able to access and/or control. A door group is assigned to an access level to restrict the ability for a user to gain entry or exit to certain doors. Select the Doors tab to add doors to the group. Include All Doors Include All Doors: Select this option to include ALL doors in the group. Doors The doors that belong to the door group. Select doors by clicking Add and dragging them to the window from the list that is displayed.
Address Module Type: The type of module that the input is attached to. Module Address Input: The address of the module that the input is attached to. Module Input: The index of the specified input on that module. Configuration Control Output/Output Group: The output that is assigned to the input. This will activate whenever an input type process's the input with the activate input output options enabled.
Inputs | Options Options 1 Log to Event Buffer: When enabled, the input will generate an event whenever it is opened, closed, tampered or shorted. The input will still perform all functions that are programmed if this is not enabled. When using inputs as automation inputs it is recommended to disable the event logging option to reduce the impact on the event log buffer.
Door Types Door types define how a door will operate, and when the door type is valid. General Name: The name of the door type. General Configuration Operating Schedule: The door type schedule allows a door type to be scheduled for use during a certain time period.
Door Types | Options Door REX Not Allowed: When enabled the door will disable the REX (request to exit) operation. Door REN Not Allowed: When enabled the door will disable the REN (request to enter) operation. Input Types Input types define how an input will operate in an area. General Name: The name of the input type. Configuration 58 Operating Schedule: Determines when the input type is valid and if it will use a secondary input type when the schedule is not valid.
Input Types | Options 1 Alarm Options Generate Alarms: When enabled the input type will process alarms from the input that it is assigned. Generate 24HR Alarms: When enabled the input type will process tamper alarms from the input that it is assigned. Entry Delay Input: When enabled the input type will start the entry delay timer for the assigned area when the input generates an alarm.
Report Bypass: When enabled the input type will generate a reportable bypass message. Report Restores: When enabled the input type will generate a reportable restore message. Stay Input: When enabled the input type will generate an alarm if the area is armed in stay mode. The input will stay armed. For inputs that will be active when an area is armed in stay mode it is recommended to disable the event log for the input.
Activate Entry Output on Bell Time: When enabled the input type will activate the entry output programmed for the area for the duration of the bell siren time. Use this feature for an input that you want to only generate a beeper alarm and assign the entry output a keypad beeper output. This option will not function if the bell option is enabled. Output Activation Options Activate Bypass Output: When enabled the input type will activate bypass output for the area if an input is bypassed.
Always Log Input Event: When enabled, the input will generate an event whenever it is opened, closed, tampered or shorted. Use Alternate Entry Time: When enabled the input type will start the alternate entry delay timer for the assigned area when the input generates an alarm. Areas Areas allow for the Protege system to be divided up into separate sections (alarm areas or partitions). This allows for areas to be grouped for easy management of multiple areas at a time.
Timings Entry Time (seconds): Setting an entry delay time for the area allows users that have entered a secured point to have time to disarm the area before the area generates an alarm. Only inputs that have an input type assigned with an entry delay option set will start the entry delay timer for the area. Alternate Entry Time (seconds): Defines the entry delay time when using an alternate entry to the area.
Areas | Outputs 64 PRT-WX-DIN Using Protege WX Installation and Programming Manual | June 2013
Bell Output/Output Group: You can assign a bell/siren output or output group to activate whenever the area goes in to alarm. The input that triggers the alarm must have the bell output option enabled for the input type. The bell/siren output and output Group will be deactivated when the bell timer times out or when the area is disarmed, the bell/siren may also be disarmed when the user logs in to the keypad.
66 Armed Pulse On Time: The armed output pulse on time is used to make the output pulse on and off when activated. The value entered here must be greater than 0 and is in increments of 100ms. For example setting 10 will pulse the unit on for 1 second and then off for the programmed time set in the pulse off section. Armed Pulse Off Time: The armed output pulse off time is used to make the output pulse on and off when activated.
Areas | Options 1 General Options Input Restore on Bell Cut-Off: When enabled the inputs that are assigned to this area will restore when the bell time completes. This does not prevent the input from generating multiple alarms for another area when this setting is specific to the area assigned. The inputs in the area will still log an event regardless of the bell time to prevent an input from triggering an event remove the event log option in the input configuration.
Reporting Options Report Arming: When enabled the area will generate a reportable event that can be directed to a monitoring station. Report Disarming: When enabled the area will generate a reportable event that can be sent to a monitoring station. Report 24HR Area Disarming: When enabled the area will report both an opening (Disabled) or closing (Enabling) of the 24HR section of this area.
Advanced Options Enable Stay Arming: When enabled the area can be stay armed. Enable Force Arming: When enabled the area can be force armed. Enable Instant Arming: When enabled the area can be instant armed. Do Not Arm if Trouble Condition: When enabled the area will be prevented from arming if a trouble condition is present in the system. Prevent Arming On Count Not Zero: When enabled the area will be prevented from arming if the count value for the area is greater than 0.
Area Groups Area groups are assigned to an access level and are used to control the areas that a user can arm and disarm. An area group can be assigned for arming and disarming. Areas assigned in the disarm area group can also be armed by the user. Select the Areas tab to add areas to the group. Include All Areas Include All Areas: Select this option to include ALL areas in the group. Areas The areas that belong to the area group.
Address: Module Type: The type of module that the output is attached to. Module Address: The address of the module that the output is attached to. Module Output: The index of the specified output on that module. Configuration: Activation Schedule: The activation schedule is programmed to activate the output at a certain time of the day or to activate the output between certain hours.
will be deactivated. Preset Module Power Up: When enabled, the state of the output will be set when the module powers up and will override the current state that is held in the controller. Output Turns On When Module Powers Up: Defines the state of the state of the output when the Preset Module Power Up option is enabled. If enabled, the output will be activated. If disabled, the output will be deactivated.
Menu Groups Menu groups provide a way of grouping together the various keypad menus that are programmed in the system. Menu groups can be assigned to an access level, determining which keypad functions those users have access to. General Name: The name of the menu group. Operating Schedule: The operating schedule for the menu group determines when the menu group is valid and if it will use a secondary menu group if the schedule is not valid.
Area Group Control Allowed: When enabled, will allow the user to access the area group control screen from the area status display screen. Tamper Area Control Allowed: When enabled, will allow the user to access the tamper area control screen. Stay Arming: When enabled, will allow the user to stay arm an area. The area must also have the stay arming option enabled. Force Arming: When enabled, will allow the user to force arm an area. The area must also have the force arming option enabled.
General Name: The name of the trouble input. Address Module Type: The type of module that the input is attached to. Module Address Input: The address of the module that the trouble input is attached to. Module Input: The index of the specified input on that module. Configuration Trouble Group: The high level of flexibility that is provided with the Protege System allows the definition of the trouble type and group that is generated by a trouble input.
Reporting ID: The Trouble Input Reporting ID allows the installer to program any reporting number to any trouble input. This provides an extremely high level of flexibility to assign true reporting numbers to the trouble inputs. A trouble input that is assigned the same reporting ID as another trouble input will result in both the trouble inputs reporting that ID.
Latch Bypassing Not Allowed: When enabled the trouble input is a high security trouble input and cannot be latch bypassed. Advanced Options No Bypass If Any Area Armed: When enabled, the input will be prevented from being bypassed if it is already assigned to an area that has either the 24HR processing enabled or the area is armed. Phone Numbers Phone numbers are defined so that a telephone number can be assigned to a Contact ID service that communicates using a modem or telephone connection.
Type Service Type: The type of service that is programmed determines the operation that this service performs. This also determines the programming screens that follow in each of the sub sections as the programming of services can contain many features and options dependent on this selection. The following section provides an explanation of each service type. Services require the use of onboard hardware devices or expansion devices.
Contact ID | Options Use Alternate Dialing Method: When enabled the service will switch between phone numbers 1 and 2 if a connection cannot be made. If the first phone number fails, the service will switch to the second phone number and vice versa until the max number of attempts is reached. Pause After PABX: When enabled the dialer will insert a pause of 2.5 seconds after the PABX telephone number is dialed.
Contact ID | Settings 80 Area Group: Defines which areas the service will process when a reportable event is generated. If an area group is not set (default), all areas are processed. CID Mapping: With the size of the Protege system the maximum reporting points available in the Contact ID format is easily exceeded, to allow flexibility a reporting table has been created to allow information to be sent using predefined input numbers or values.
Report IP This service allows the Controller to send alarm and activation information over an IP connected network. The Report IP Service supports multiple formats and allows the connection to third party reporting if required. Report IP | General Client Code: The account number for the Report IP Service can be up to 8 digits. An account code with leading zeros will be truncated to send the minimum number of digits, for example the account code 004311 will be sent as 4311.
SIA Over IP: SIA Over IP communicates a SIA Level 2 message using the SIA DC09 specification format to any receiver that supports the SIA DC09 specification. SIA DC09 Specification is currently not released as a formal specification and is subject to change. CID Over IP: CID Over IP communicates a Contact ID message using the SIA DC09 specification format to any receiver that supports the SIA DC09 specification.
Switch Secondary IP Immediately: When enabled the service will immediately use the secondary IP settings. Report Open: When enabled the service will report opens (Disarming) for the areas that are part of the area group assigned. An area group of none will mean ALL areas will be sent using this service. Report Close: When enabled the service will report closes (Arming) for the areas that are part of the area group assigned.
Scheduling The Scheduling menu contains the functions relating to date and time information, including schedules and holiday groups.
Holiday Groups Holiday Groups are used to prevent (or allow) periods within a schedule from functioning during the holiday duration. Select the Holidays tab to add holidays to the group. Name: The name of the holiday. Repeat: When enabled, the holiday will recur on an annual basis. Start Date: The start date of the holiday. End Date: The end date of the holiday. Daylight Savings Daylight savings periods are associated with a controller.
Schedules Schedules enable a function or access level to operate only within certain scheduled periods. Each schedule contains up to 8 periods that can have various times and days programmed. Holiday groups can also be selected to allow a schedule to function when a holiday is active. 86 Name: The name of the schedule. Period 1-8: Time periods for the schedule.
Schedules | Options Invalidate Schedule if Qualify Output On: When enabled the schedule will only operate if the qualify output is on and will be invalidated when the output turns on if it was valid. Invalidate Schedule if Qualify Output Off: When enabled the schedule will only operate if the qualify output is off and will be invalidated when the output turns off if it was valid. Qualify Output: The schedule can be qualified using an output.
Expanders The Expanders menu contains the settings required to connect and configure the various expander modules available that extend your Protege WX system.
Smoke Reset Output/Output Group: The output (or output group) that is programmed as the keypad smoke detector reset output will be activated when a user presses the CLEAR + ENTER keys together. Time User Is Logged In (Seconds): When the user does not perform any action on the keypad for the programmed time, the keypad will automatically log the user out. Programming the option 'Never Logout' should be avoided unless for training or demonstration purposes.
Access Options Function Key Unlocks Door When Logged In (REX): When enabled, allows the user to unlock the controlled door by pressing the FUNCTION key when they are logged in. Keypad Can Access Only Primary Area: When enabled, the keypad will only allow the user to access the keypad's primary area. Allow Area Group Selection Access: When enabled, the keypad will allow the area group access screen to be accessed by the user.
Analog Expanders Analog Expanders are used to connect industrial automation devices to your Protege system. General Name: The name of the analog expander. Configuration Invert Device Tamper: When enabled, the analog expander will invert the module tamper input allowing a normally open tamper switch to be used. When disabled the analog expander will use the standard normally closed tamper switch. Physical Address: The device address of the Analog Expander.
Output Expanders Output Expanders extend the number of outputs available within the system. General Name: The name of the output expander. Configuration Physical Address: The device address of the Analog Expander. Reader Expanders Reader Expanders extend the number of reading devices and locking inputs available within the system. General Name: The name of the reader expander.
Reader Expanders | Reader One-Two Configuration Reader Format: The reading format used to inform the reader expander what type of card readers are connected to the reader port. The reader expander supports nearly all publicly available protocols and some special protocols. Any 26 or 37 bit card reader that conforms to the standard format specification will work on the Reader Expander. 26 Bit: The industry standard 26 bit format consisting of 8 site code/facility bits and 16 bits of card information.
94 Sentrax 9000 T2: A track 2 magnetic card format utilized in New Zealand by the Sentrax T2 Access Control System. Uses an 8 digit site code and 10 digit card number encoded with expiration and utility codes. This format ONLY decodes the Facility and Card numbers. Propel Track 2: A track 2 format used through out Asia proprietary based for Propel Systems Sdn Bhd of Kuala Lumpur.
NCS 29 Bit: An older format that is used by Northern Control Systems and is a 29 Bit Format. HID 34 Bit: A standard HID format consisting of a 16 digit site code and a 16 digit card number with parity calculated on the end two bits. HID 26/34 Bit: A dual format consisting of the standard 26 Bit and Standard 34 Bit formats. Auto - Wiegand: Automatically selects the best available Wiegand format from the formats to decode the card.
Reader Door: The reader controlled door setting sets the door that the reader on port one will provide card and control information to. It is possible that more than one reader has the same controlled door (Entry and Exit reading configuration). Reader Keypad Type: The keypad operation mode programmed for the reader on a port determines if the reader port has a pin entry device attached or uses a local LCD keypad. LCD Keypad: An LCD keypad is used for PIN entry.
Reader Options Allow Reading Opened/Unlocked: When enabled, the reader expander will send card information to the system controller when a door is unlocked or opened. This option is set by default and should be left set if the door control areas or time and attendance events are required from the reader port. When disabled the reader performs no action when a card is presented and the door is unlocked or open.
Reader Expanders | Reader 1-2 Options 98 Enable Beam Function On Input: When enabled, the reader expander will process the sense input for beam control. Beam control allows the reader expander to control an automatic gate which must have its contacts held open even if the pathway is blocked. When disabled the reader will not perform beam processing. Invert Door State Control: When enabled, the door contact input is inverted.
Recycle REX Time: When enabled, will restart the door open time allowing the door to be held open and the REX pressed at each point the pre-alarm starts silencing the pre-alarm and restarting the open timer. This allows a door to be held while furniture is being moved or to provide extended access for mobility users.
System The System menu is used to configure system settings, backup programming and update firmware.
Display Default Display Line One: The default LCD text for line one is shown on LCD keypads when they are first connected to the system. This text should be changed to the name of the building, installation or owners details. Default Display Line Two: The default LCD text for line two is shown on LCD keypads when they are first connected to the system. This text should be changed to the name of the building, installation or owners details.
Options Test Report Time is Periodic: When enabled, the test report trouble input will be activated at the frequency defined by the Test Report Time. When disabled the test report trouble input will be activated at the specified time of day. Generate Input Restore On Test Report Input: When enabled the Controller will generate a restore event for the trouble input test report input restoring. This occurs one minute after the trouble input has been activated.
E-mail Email: The email address of the operator. Currently only used for information purposes. Default Reporting Language: Reserved for future use. Operator Timeout Enable Operator Timeout: Select this option to automatically log the operator out after a period of inactivity as defined in the Operator Timeout setting below. Operator Timeout: Defines the inactivity period at which point Protege WX will timeout and the operator will be prompted to login again to continue.
Maintaining Your System This section covers system maintenance, including how to backup and restore Controller programming, update firmware, and addressing additional expanders that are added to the network. Changing the Admin Password For security reasons, it is important that you change the default admin password when Protege WX is first installed. You can also change this later. 1. To change the admin password, navigate to System | Operators and select Administrator 2.
Backing Up and Restoring Controller Programming Creating backups of your Controller programming is good practice to ensure you are protected against damage in the event of hardware failure or malfunction. The Protege WX interface provides a simple export tool for backing up the system to a SQL backup file (*.BAK). This file works as a snapshot of your current system, enabling you to later restore and retain the programming at the same point as you exported it.
Upgrading Firmware From time to time, ICT release new firmware with updates and enhancements to the features included. To ensure your installation is running at the optimal performance, we recommend that all installed modules utilize the latest firmware releases. 1. From the main menu, select System | Firmware. The Firmware page opens containing details about the current firmware version that is installed. 2. Click the Choose File button and browse to the supplied update file. 3.
Configuring the IP Address The Controller must be programmed with a valid IP Address to allow communication. By default this is set to 192.168.1.2 but can be adapted to suit your network requirements and addressing scheme. i Programming the IP Address, Subnet Mask, and Default Gateway requires knowledge of the network and subnet that the system will be connected to. You should always consult the network or system administrator before programming these values. 1.
Temporarily Defaulting the IP Address If you don't know the currently configured IP address, you can temporarily set to 192.168.111.222, then connect to the web interface to view and/or change it. This resets the IP address for as long as power is applied but does not save the change permanently. Once the link is removed and power is cycled to the unit, the previously configured IP address is used again. 1. Remove power from the Controller by disconnecting the 12V DC input. 2.
To Set the Network Address of a Module: 1. Ensure the Controller is correctly powered. 2. Connect the module(s) that require addressing to the module network. Make sure that the Power light on each module is on and that the Status light begins flashing rapidly. 3. Allow some time for the module(s) to attempt to register with the Controller. If the module has the default address of 254 or has the same address as another module, the Fault light will begin flashing at 1 second intervals.
Troubleshooting This section includes helpful troubleshooting information. Common Health Status Messages The Health Status is displayed on the Home Page and provides details of the overall status of the system and can be useful in identifying any problem areas that need to be addressed. It lists any problems that the Controller has with its current configuration.
Areas Requiring Rearming due to Input Changes Typical Health Status Message Area Warehouse requires rearming due to Input Warehouse PIR changes Cause The 24 hour portion of an area must be rearmed when programming changes result in the input functioning in a different manner. This is to prevent inadvertent changes to a live system that could result in an undetected security breach. Solution 1. Navigate to Monitoring | Areas and click Controls to open the manual control window. 2.
Items that Can't Fit in the Database Typical Health Status Message Input Warehouse PIR will not fit into the internal database Cause Each module only has a set number of inputs and outputs. For example, the Controller has 8 inputs and 3 outputs, whereas a Reader Expander has 8 inputs and 8 outputs. If you add a record where the address is higher than the maximum allowed for that Expander, it cannot be added to the system.
Contact Integrated Control Technology welcomes all feedback. Please visit our website (http://www.incontrol.co.nz) or use the contact information below. Integrated Control Technology P.O. Box 302-340 North Harbour Post Centre Auckland New Zealand Phone: 11 Canaveral Drive Albany North Shore City 0632 Auckland New Zealand +64-9-476-7124 Toll Free Numbers: 0800 ICT 111 (0800 428 111) - New Zealand 1800 ICT 111 (1800 428 111) - Australia 1855 ICT 9111 (1855 428 9111) - USA/Canada Email: sales@incontrol.
Index A D Access Control • 24 Daylight Savings • 85 Access Levels • 46 Defaulting a Controller • 106 Access Levels | Area Groups • 47 Different Hours for Weekends • 33 Access Levels | Door Groups • 47 Door Groups • 54 Access Levels | Doors • 47 Door Types • 57 Access Levels | Menu Groups • 47 Door Types | Options • 58 Addressing Expanders • 99, 108 Doors • 49 Analog Expanders • 91 Doors | Advanced Options • 53 Area Groups • 70 Doors | Options • 24, 51 Areas • 62 Doors | Outputs • 50 Ar
M Maintaining Your System • 104 Menu Groups • 73 Menu Groups | Options • 74 Modem Indicator • 38 Module Wiring • 12 Modules that are Offline • 110 Modules that Require a Restart • 110 Monitoring • 48 Monitoring Your System • 36 Mount the Controller • 8 Multiple Periods in a Single Day • 34 Multiplex Card Reader Connection • 14 O Operation Mode • 6 Operators • 102 Output Expanders • 92 Output Groups • 72 Outputs • 8, 19, 70 Outputs | Options • 71 Over Current Indicator • 41 Overlapping Periods • 35 Securit
