Instructions / Assembly

BT-PRIMER
QUANTITY PACKAGING
1 Gallon 4 gallons/carton
5 Gallon pail 1 pail
PROTECTO-TAK SPRAY ADHESIVE
QUANTITY PACKAGING
13 oz can 12 cans/carton
*Dens-Glass is a registered trademark of Georgia-Pacific Corporation
BT-PRIMER and PROTECTO-TAK SPRAY ADHESIVE DATA SHEET
DESCRIPTION:
BT-Primer and Protecto-Tak Spray Adhesive are high tack primers for use under the BT-Series products over Dens-Glass Gold*, all OSB board, black
sheathing board, metal, wood, dry concrete and dry masonry. When used over Dens-Glass Gold*, BT-Primer is moisture tolerant and is suitable for use on
moist or damp Dens-Glass Gold*. BT-Primer and Protecto-Tak Spray Adhesive are VOC compliant.
PROPERTIES:
Protecto-Tak
BT-Primer Spray Adhesive
Adhesion to wood Excellent Excellent
Adhesion to steel Excellent Excellent
Adhesion to dry concrete Excellent Excellent
Adhesion to dry masonry Excellent Excellent
Adhesion to membrane Excellent Excellent
Coverage 150 sq. ft./gal. 2 oz: 4" x 100' roll
Shelf life (min.) One Year One Year
Tack free time (minutes) 20-45 minutes 2-10 minutes
Flash Point 24˚F TCC -42˚F TCC
DIRECTIONS FOR USE:
PREPARATION:
BEFORE HANDLING read material safety data sheets for health information.
• The surface shall be cleaned so that all dirt, dust, loose concrete, or other contaminants that may adversely affect the adhesion of the membrane are
removed.
BT-PRIMER APPLICATION:
• Apply primer to all surfaces by roller or brush.
• Primed surface shall be free of runs, puddles or excessive primer as this could cause blistering. Brush or roll out all primer puddles or drips
immediately.
• Prime only as much area as can be covered in half a day’s work. Re-prime areas not covered in half a day’s work with a light coat of BT-Primer.
•Tack free time is approximately 20 to 45 minutes.
NOTE: Some bubbling in the primer may occur on the surface as it cures. This has no effect on the performance of the product and will smooth out as the membranes are applied.
PROTECTO-TAK SPRAY ADHESIVE APPLICATION:
• Shake can before using.
•Turn spray tip so arrow points to dot on rim.
• Hold can 6 inches from surface to be sprayed and apply to surface.
•After each use, invert container and spray until nozzle clears. Clean clogged spray tips with hot water.
• Clean oversprayed areas with a mix of 25% - 30% water added to isopropyl alcohol.
PACKAGING AND WEIGHTS:
BT25XL 01 06/07
1955 South Cherokee St., Denver, Colorado 80223
[phone] • Fax [phone] • 1-800-759-9727
www.protectowrap.com
• Stop moisture intrusion that causes
black mold
• No special tools needed, peel and stick
installation
• Meets or exceeds all building codes
including ASTM 2112
• Meets or exceeds ICC Code Approval
ESR1825
• The only flashing tape that passed
hurricane level windblown rain test
ASTM E331-90
• Adheres to vinyl, plywood, OSB, foam,
metal, aluminum, and masonry
• Can be left exposed up to 120 days
PROTECTO WRAP BT25XL BUTYL HYBRID
WINDOW & DOOR SEALING TAPE can help
reduce air infiltration as recommended by the
ENERGY STAR HOME SEALING guidelines.
BT25XL Butyl Hybrid Window
& Door Sealing Tape
S
T
O
P
M
O
L
D
S
T
O
P
M
O
L
D
Forms a permanent waterproofing air/vapor seal around
doors and windows that prevents air and moisture leaks.