By ProSun International, LLC. 15 Minutes ProSun X5 34 SLi Intensive ProSun X5 34 SPr Intensive User’s Manual ProSun International, LLC 2442 - 23rd Street North St. Petersburg, FL 33713-4018 Website: www.prosun.com Phone: Fax: Toll Free: E-mail: 727-825-0400 727-825-0700 800-874-2776 sales@prosun.
Contents Warning Labels.....................................3 Lamp compatibility chart...........................4 Electrical requirements.............................5 Read this firts.......................................6 10 Golden rules .................................................7 General electric notes..............................8 Beauty and responsible tanner....................9 The tanning process..............................10 Care and maintenance...........................
Congratulations on the purchase of your ProSun tanning bed. Your new tanning bed has been manufactured with the utmost care and attention and consists of high-quality parts. All ProSun tanning beds have been developed to give you the best possible tan, whilst complying with the strictest applicable FDA & UL/CSA standards.
THE FOLLOWING INSTRUCTIONS ARE IN COMPLIANCE WITH ‘POLICY ON LAMP COMPATIBILITY’ , 21 CFR 1040.
Important Notice: • NEVER OPERATE THIS MACHINE WHEN THE AMBIENT ROOM AIR TEMPERATURE IS GREATER THAN 90 DEGREES FAHRENHEIT. • NEVER OPERATE THIS MACHINE IN A COMMERCIAL APPLICATION WHEN THE REMOTE TIMER IS NOT WORKING PROPERLY. • NEVER OPERATE THIS MACHINE WHEN THE BLUE FILTER GLASS IN ANY FACIAL TANNER IS NOT INSTALLED OR IS BROKEN / DEFECTIVE. • NEVER OPERATE THIS MACHINE WHEN IT IS NOT VENTILATING ITSELF PROPERLY (TOO HOT INSIDE).
Read this first 1 Contact ProSun Tanning International immediately if this unit does not function as outlined in this manual. 800-874-2776 or tr CSV. 800-501-8485 2 Do not operate this unit in a moisty or humid space. 3 Always make sure the fuses can carry the load Note: Please consult enclosed tanning schedule for advised tanning times. Repairs may only be carried out by qualified personnel. Always disconnect the main power at the circuit breaker before servicing or repairing the unit.
THE FOLLOWING INSTRUCTIONS ARE IN COMPLIANCE WITH ‘POLICY ON LAMP COMPATIBILITY’ , 21 CFR 1040.20(e)(2)(iii) 10 Golden rules for sensible tanning Note: If your customers are using medication, ask them to consult their doctor before embaking on a series of tanning sessions. 1 Before your client takes his or her tan in a tanning unit first consult thoroughly the tanning table that you will find in this book and follow its recommendations. 2 People have different reactions to sunlight.
GENERAL ELECTRICAL NOTES • ALL ELECTRICAL WORK SHALL COMFORM TO THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODE, O.S.H.A. OR APPLICABLE LOCAL AND OR STATE ORDINANCES, ASWELL AS UTILITY COMPANY RULES REGARDING AMPERE INTERUP TION AND SAFETY SHUNT TRIP SWITCHES AND POWER PANELS OF WHICH SHALL BEAR THE LABEL OF UNDERWRITER’S LABORATORIES, INCORPORATED AND SHALL BE PERMANENTLY MARKED FOR EASY IDENTIFICATION. • ALL WIRES SHALL BE SINGLE SOLID RUNS WITHOUT SPLICES MEETING THE N.E.M.A. STANDARDS.
BEAUTY AND THE RESPONSIBLE TANNER Many people in today’s image-conscious society want to be tanned. The Romans built large sunning terraces onto their villas so as to take advantage of the sun’s spiritually and physically therapeutic effects. They somehow inherently knew of the positive influences that natural sunlight could lend to the human condition, millennia before the science of photobiology was conceived of.
THE TANNING PROCESS The sunbed you have purchased is designed to concentrate optimal levels of UVA, in conjunction with very low percentages of UVB, on the outermost layers of the skin, so as to stimulate the production of Melanie pigment, which is slightly pink in its dormant state, and cause it to turn brown after excretion. The more Melanin cells present in the skin determines the amount of pigment that will be excreted and distributed, and therefore the extent of the tan.
CARE AND MAINTENANCE The Care and Maintenance in this section covers most of the difficulties that you may encounter under normal working circumstances. If your tanning bed fails to operate properly, please review the following steps before calling for service. THE TANNING BED YOU PURCHASED CONTAINS VOLTAGES WHICH ARE POTENTIALLY HAZARDOUS. ALL REPAIRS AND GENERAL MAINTENANCE SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL.
Preventive Maintenance Frequency: Clean Acrylic's Inspect Facial glass if applicable Clean and Sanitize goggles Clean and sanitize bed exterior Remove and clean the inside acrylic's Wipe and vacuum fan's, vents and venthoses Clean all reflectors Inspect Acrylic's for crack wear Replace the acrylic's Adjust gasschock or spring's tension if needed Check combi set bolts for proper tightness Inspect vent hoses for optimum cooling Afther each session Daily * * Weekly Monthly * * Every 1200 hr.
MAINTENANCE Cleaning the machine: Always disconnect the main power from the unit before attempting to clean or repair it. Dust the lamps with a dry cloth - do not use cleaning fluid or alcohol. The acrylics should be taken out at least once every week of operation and cleaned thoroughly with a nonalcoholic disinfectant glass or surface cleaner. If alcohol is used, the acrylic may fade, crack, or break altogether.
REPLACEMENT OF COMPONENTS WARNING: Before doing any repair or replacement work on this machine, ALWAYS disconnect the power (or, if the main power cable has a wall plug, pull it out) at the main circuit breaker. Opening the bench acrylic: WARNING: Let the tanning bed cool down for one hour before opening the acrylic 's. To unlock and raise the acrylic sheet for cleaning and bulb replacement, use a coin to turn the screws counter-clockwise. Lift the acrylic and support it by the metal rod.
Problem Probable cause possible solution Unit is activated but nothing happens Timer clears after priming Remote timer is not working Bed appears too be to hot Fans are obstructed Check to see if the power source has been properly connected Restart the timer and try again Check remote connections Ensure all fans or clear of obstructions and dust.
ProSun® International, LLC. LIMITED WARRANTY EFFECTIVE January 01, 2006 1. Warranty Period: PROSUN warrants new tanning equipment manufactured or imported by it, provided it is still owned and operated by the original purchaser, to be free from defects in material and workmanship under normal use and service, for a prorated period of two (2) years from the date of delivery to the original Purchaser. 2.
Controls The default settings for the sun bed are for use with an external timer or for coin-operated use. If the sun bed is used without an external timer or not coin-operated, and the internal timer needs to function, the required tanning time should be set following the procedure described below. General + Config. Keep the “config” and the “increase body cooling” buttons pressed simultaneously for 10 seconds. Increase body cooling After 10 seconds, the display will show “SET 20”.
Control without the use of an external timer or coins: The tanning time can be decreased by pressing the “start” button once. A Start The display will show “SET” and the set maximum tanning time. B Use the “decrease” “increase body cooling” buttons to decrease and increase the tanning time. Increase body cooling Decrease body coolingr C The sun bed can be started by pressing the “start” button. Start D Stop The equipment will pause when the “stop” button is pressed once.
(optional) The “air conditioning” button is used to switch the airco on and off. It will be turned on by default at the start of each tanning session. D Air conditioning Note: A. The air conditioning can be switched off by pressing the button for at least 2 seconds. B. Once the air conditioning has been switched off, it must cool down for 3 minutes before it can be switched on again. If the “air conditioning” button is pressed during cool-down, the display will show the remaining cooling down time.
Error messages: Error! Internal timer has a defect Error! Ventilator in bottom tray has a defect Error! Communication fault between control and switch parts ! To be able to read the hour counter for the lights, press the the “config” and “increase volume” simultaneously for 3 seconds and keep them pressed. + A Config. ! If one of the above error messages appears on the display, you must stop using the sun bed and take the plug out of the socket. Please contact your dealer.
Dimensions in inches 94.5 inch 4 inch 14 inch 46 inch 90.5 inch 59.5 inch 21.6 inch 49 inch 45.5 inch 50.
Dimensions in milimeters 22
Removing the acrylic sheets Démontage des plaques en acrylique Desmontaje de las placas acrílicas Warning! Before obtaining access to terminals, all supply circuits must be disconnected. Attention! Débranchez l'appareil avant de procéder à son entretien 2 1 Atención! Antes de realizar el mantenimiento, desconecte el aparato de la corriente eléctrica.
Removing the filter holders Démontage des supports de filtres Extracción de portafiltros 1 2 Removing the face tanners Démontage des lampes visage Extracción de bronceadores de rostro 24
Assembly Montage Montaje 1 2 25
Assembly Montage Montaje 3 4 26
Assembly Montage Montaje 5 6 27
Assembly Montage Montaje 7 8 28
Assembly Montage Montaje X7 42 SLi X7 38 SLi X5 34 SLi X5 34 SPr X= 2.75 inch X= 2.5 inch X= 2.1 inch X= 1.2 inch 9 X Max 3.75 inch Max.
Assembly Montage Montaje 11 Optional 30
Assembly Montage Montaje 12 13 31
Assembly Montage Montaje 14 15 32
Assembly Montage Montaje 16 0 Black 17 33
Assembly High Intensive 160W Montage Montaje 18 3/4 inch 34
Assembly Montage Montaje 19 4.
Assembly Montage Montaje 21 36
Assembly Montage Montaje 22 Remote Remote 37
Assembly Montage Montaje 23 38
Assembly Montage Montaje 24 39
Assembly Montage Montaje 25 40
Assembly Montage Montaje 26 41
Assembly Montage Montaje 27 28 42
Assembly Montage Montaje 29 43
Assembly Montage Montaje 30 31 32 3 2 1
Electrical diagrams Schéma électrique Diagrama eléctricas
