Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. • Position the display directly in front of you at a comfortable viewing distance. • Adjust the display-viewing angle to find the best position.
Preface Contents Notice ...........................................................................I FCC Statement .......................................................II Instructions for Care and Operation ..................... IV Power Safety ........................................................ VI Battery Precautions .............................................VII Cleaning ............................................................ VIII Servicing ..................................................
Preface Application Hot-Key ..............................................2-10 TouchPad and Buttons/Mouse ...............................2-11 Configuring the TouchPad and Buttons ..............2-11 Audio Features .......................................................2-12 Adding a Printer .....................................................2-13 USB Printer .........................................................2-13 Parallel Printer .....................................................
Preface Wireless LAN (WinXP) ......................................4-11 Bluetooth (WinXP) .............................................4-11 PC Camera (WinXP) ...........................................4-11 Port Replicator (WinXP) .....................................4-11 BIOS Utilities Overview ..................................................................5-1 The Power-On Self Test (POST) .............................5-2 Failing the POST ....................................................
Preface Modules & Options Overview ..................................................................7-1 Mini-PCI WLAN Module ........................................7-2 MSI 6833 WLAN Driver Installation ...................7-3 Bluetooth Module .....................................................7-6 Bluetooth Driver Installation ................................7-6 PC Camera Module ..................................................7-8 Sertek PC Camera Driver Installation ...................
Preface Serial Port ................................................................A-4 RJ-45 LAN Jack ......................................................A-4 USB 2.0/1.1 Ports ....................................................A-5 Video Driver Controls VIA Video Driver Installation ................................. B-1 Advanced Video Controls ....................................... B-2 Video Driver Controls .......................................... B-2 Video Memory ....................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 4-in-1 card reader, PC Card), Auto Mail Program, Touch Pad & Mouse, Audio & Printer.
1 Quick Start Guide Model Differences This notebook series includes two different model types. The models differ slightly in design style including the LCD type, and the location of the card reader. See Figure 1 - 1 below and Table 1 - 1, on page 1 - 3 for an outline of the model differences.
Quick Start Guide Feature Model A Model B LCD Type 15.0” XGA (1024 * 768) TFT OR 15.0” SXGA+ (1400 * 1050) TFT 14.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Windows XP (Home & Professional Editions) operating system.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter (Note: If you have included the Port Replicator in your purchase option see page 7 - 14).
Quick Start Guide System Map: Model A - Top View with LCD Panel Open 1 1. 2. 3. 4. 5. 6. 7. 8. 9. Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide System Map: Model B - Top View with LCD Panel Open 1 1. 2. 3. 4. 5. 6. 7. 8. 9. Optional Built-In PC Camera LCD Speaker LED Status Indicators Hot-Key Buttons Power Button Keyboard TouchPad and Buttons LED Power & Communication Indicators 10.
Quick Start Guide LED Indicators Table 1 - 3 - LED Power & Communication Indicators The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators) on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Hot-Key Buttons & Keyboard These buttons give instant access to the default Internet browser and e-mail program, and to a user-defined application, with one quick button press. To use the “user-defined application Hot-Key Button”, you must install the driver (see “Hot-Key (WinXP)” on page 4 10). The keyboard has an embedded numerical keypad for easy numeric data input, and features Function Keys to allow you to change operational features instantly (see Figure 1 - 5).
Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (F3 - F12 etc.).
1 Quick Start Guide System Map: Front & Rear Views Figure 1 - 6 Front & Rear Views 1. 2. 3. 4. 5. 6. 7.
Quick Start Guide System Map: Left View Figure 1 - 7 Left View Model A 1 2 6 3 3 4 5 3 3 4 5 7 Model B 1 6 2 1. 2. 3. 4. 5. 6. 7. RJ-45 LAN Jack Vent/Fan Intake 2 * USB 2.
1 Quick Start Guide System Map: Right View Figure 1 - 8 - Right View 1. 2. 3. 4. 5. Headphone-Out Jack Microphone-In Jack USB 2.0 Port Optical Device Drive Bay (for CD/ DVD Device - see page 2 - 3) DC-In Jack 1 2 3 4 5 Changing DVD Regional Codes CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide System Map: Bottom View Model A Figure 1 - 9 - Bottom View 2 CPU 1 The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 3 Vent/Fan Intake Battery Memory (RAM)/WLAN Module/CPU Cover Hard Disk Cover Speakers (Model A Only) 4 Model B Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. 1. 2. 3. 4. 5.
1 Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the video driver is installed. For further video information see “Advanced Controls” on page 3 - 1. 1. 2. 3. 4. 1 5. 2 6. 3 7. Right-Click Desktop Click Start, point to Settings and click Control Panel (or click Control Panel). Double-click Display (icon); Display (icon) is in the Appearances and Themes category.
1 Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display as your display device if connected to the external monitor port. The following display modes are available (see “Video Driver Controls” on page B - 1 for details).
Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 1 - 16) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 12).
1 Quick Start Guide 1 - 20
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 4-in-1 Card Reader PC Card Slot Auto Mail Checker Application Hot-Key TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" parallel (PATA) hard disk drives with a height of 9.5 mm.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Features & Components 2 CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/ DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 14. .
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not is use. This will help prevent foreign objects and/or dust getting in to the card reader. 4-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PCMCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Reader Card driver (see “PCMCIA/Card Reader (WinXP)” on page 4 - 10). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot.
Features & Components Auto Mail Checker 2 After you have installed the driver for the Auto Mail Checker program (see “AutoMail (WinXP)” on page 4 - 11) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
Features & Components You may then configure the options for your mailserver, name, password, program and method(s) of notification. Note Check with your Internet Service Provider, network administrator or Mail Service provider for details on what to put on these pages.
Features & Components 2 Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right-click its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Application Hot-Key The hot-key buttons give instant access to the default Internet browser and email program, and to a user-defined application, with one quick button press.
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. The central button may be configured to function as you require.
Features & Components 2 Sound Volume Adjustment How high the sound volume can be set using the volume control knob depends on the setting of the volume control within Windows (and the volume control hot-keys on the computer). Click the speaker icon in the taskbar to check the setting.
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most current printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Features & Components 2 2 - 14
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Port Replicator AC/DC Adapter You will be provided with a 90W AC/DC adapter if you purchase the port replicator option. If you are using the computer with the Port Replicator, then you must use the 90W AC/DC adapter to power the port replicator and computer (DO NOT USE the computer’s 65W AC/DC adapter to power the Port Replicator). See “Port Replicator Module” on page 7 14 for more information.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. Shutdown When the computer is on, you can use the power button as a Standby/Hibernate/Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation The system can resume from Monitor or Hard Disk Standby by pressing the Sleep/ Resume key combination (Fn + F4), or power button. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode (Figure 3 - 3). In Standby mode, the LED will flash green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. Close modem or communication applications when they are not being used. Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities Authorized Driver Message 4 If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install WinXP Drivers (button). 1. 2. If you wish to install the drivers manually see page 4 - 7. 3. Check the driver installation order from Table 4 1 on page 4 - 6 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities WinXP SP2 Driver Page # Install the appropriate Service Pack for WinXP Page 4 - 3 Chipset Page 4 - 8 Video Page 4 - 8 Audio Page 4 - 8 LAN Page 4 - 8 Modem Page 4 - 9 TouchPad Page 4 - 9 PCMCIA/Card Reader Page 4 - 10 Hot-Key Page 4 - 10 AutoMail (Manual Driver Installation Only) Page 4 - 10 Wireless LAN Page 7 - 3 Bluetooth Page 7 - 6 PC Camera Page 7 - 9 Port Replicator Serial Port Page 7 - 16 Port Replicator Network (LAN) Port Page 7 - 16 4 Table 4 - 1
Drivers & Utilities Driver Installation Procedure Service Pack Installation This section covers driver and utility installation instructions for Windows XP Home & Professional. Make sure you install the appropriate service pack for your operating system before installing any drivers (see “Windows XP Service Pack 2” on page 4 - 3).
Drivers & Utilities 4 Chipset (WinXP) 1. Click 1.Install Chipset Driver > Yes from the Drivers Installer menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Chipset\Setup.exe and click OK. 2. Click Next > Yes > Next > Next > Next. 3. Click OK to restart the computer. Video (WinXP) 1. Click 2.Install Video Driver > Yes from the Drivers Installer menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Video\setup.
Drivers & Utilities Modem (WinXP) 1. Click 5.Install Modem Driver > Yes from the Drivers Installer menu. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\Modem\Setup.exe and click OK. 2. Click OK > OK (click Continue Anyway if asked if you want to continue at any time). 3. The modem is ready for dial-up configuration. TouchPad (WinXP) 1. Click 6.Install TouchPad Driver > Yes from the Drivers Installer menu. OR Click Start (menu) > Run... and navigate (Browse..
Drivers & Utilities 4 PCMCIA/Card Reader (WinXP) 1. Click 7.Install PCMCIA Driver > Yes from the Drivers Installer menu. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\PCMCIA\Setup.exe and click OK. 2. Click Next > Next. 3. Click Finish to restart the computer. 4 - 10 Driver Installation Hot-Key (WinXP) 1. Click 8.Install Hotkey Utility > Yes from the Drivers Installer menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Hotkey\Setup.exe and click OK. 2.
Drivers & Utilities AutoMail (WinXP) Wireless LAN (WinXP) The AutoMail Driver must be installed manually as per the instructions below: See the installation procedure in “MSI 6833 WLAN Driver Installation” on page 7 - 3. 1. Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\AUTOMAIL\SETUP.EXE and click OK. 2. To continue click Next > Next > Finish. 3. For further details see “Auto Mail Checker” on page 2 - 8.
Drivers & Utilities 4 4 - 12
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: If you have enabled the Intel OnScreen Branding Logo (see “Intel On-Screen Branding Logo (Advanced Menu)” on page 5 - 9) the POST screen will not appear. Figure 5 - 1 POST Screen The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu System Time: 5 System Date: [22:11:05] 06 [05/30/2005] Legacy Diskette A: [Disabled] IDE Channel 0 Master IDE Channel 0 Slave System Memory Extended Memory F1 Esc Help Exit Item Specific Help , , or selects field.
BIOS Utilities Legacy Diskette A: This control may be used to enable/disable, and to configure, any attached floppy disk drive. IDE Channel 0 Master/Slave (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a CD Device or HDD that on the computer’s IDE Channel 0. Use the “Auto” (Type:) setting to have the items configured automatically for you. 5 System/Extended Memory (Main Menu) This item contain information on the system memory, and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 PhoenixBIOS Setup Utility Advanced Menu Advanced Advanced Main Security Boot Exit Item Specific Help Setup Warning Setting itmes on this menu to incorrect values may cause your system to malfunction.
BIOS Utilities Installed O/S: (Advanced Menu) This setting tells the computer what kind of operating system you’re using. Reset Configuration Data: (Advanced Menu) This item is set to “No” as default. You can change the setting to “Yes” if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. 5 Large Disk Access Mode: (Advanced Menu) Select “Other” if you are using systems such as Novell, UNIX etc.
BIOS Utilities APIC interrupt routing: (Advanced Menu) Setting this menu item to “Enabled” will turn on the I/O APIC (Advanced Peripheral Interrupt Controller). This is an is an Intel architecture for dealing with interrupt requests (IRQ’s) in multi-processor computer systems, and is fully supported under Windows XP. You may want to disable this option in other operating systems. 5 PS/2 Mouse (Advanced Menu) Use this menu item to enable/disable support for a PS/2 type mouse.
BIOS Utilities Security Menu Figure 5 - 4 PhoenixBIOS Setup Utility Main Advanced Security Security Boot Security Menu Exit Item Specific Help Supervisor Password Is: User Password Is: Clear Clear Set Supervisor Password Set User Password Enter] [E [Enter] Password on boot: [Disabled] Supervisor Password controls access to the setup utility.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the Setup utility.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Boot F1 Esc Help Exit Select Item Select Menu -/+ Enter Item Specific Help Boot Menu Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. and specifies the device fixed or removable. exclude or include the device to boot. enables or disables a device. <1 - 4> Loads default boot sequence.
BIOS Utilities When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”. If you wish to boot from a CD-ROM/DVD-ROM you will need to add it to the boot order. As a general rule the order below is recommended: 5 1. 2. 3. 4.
BIOS Utilities Exit Menu Figure 5 - 6 PhoenixBIOS Setup Utility Exit Menu Main Advanced Security Boot Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow, and hold it in place. Slide the battery in the direction of the arrow 2 . Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Upgrading The Computer 4. Lift the battery out in the direction of the arrow 3 . Figure 6 - 2 Battery Up 3 5. Lift the battery 4 out.
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" parallel (PATA) hard disk drives with a height of 9.5mm (h) (see “Storage” on page C 3). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in “Driver Installation” on page 4 - 5), when setting up a new hard disk. 1. 2. Turn off the computer, and turn it over and remove the battery.
Upgrading The Computer For Model A computers (see overleaf for Model B): 3. 4. 5. 6. Slide the hard disk and cover assembly in the direction of arrow 4 . Lift the hard disk and cover assembly up in the direction of arrow 5 . Remove the hard disk and cover assembly 6 . Remove the 4 screws to release the hard disk from the assembly cover, and reverse the process to install any new hard disk.
Upgrading The Computer For Model B computers: 7. 8. Pull the tab to slide the hard disk and case assembly in the direction of arrow 7 . Lift the hard disk and case assembly out of the bay in the direction of arrow 8 9. . Remove screws 9 - 10 to release the hard disk 11 from the case 12 , and reverse the process to install any new hard disk.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. 5. Turn off the computer, and turn it over and remove the battery. Locate the memory bay cover and remove screws 1 - 7 (Model A)/ 1 5 (Model B). Remove the bay cover 8 Use a screwdriver to carefully push out the optical device at point 9 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has one memory socket for 200 pin Small Outline Dual In-line (SO-DIMM) DDR type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the memory bay cover and remove screws 1 - 7 (Model A)/ 1 5 (Model B).
Upgrading The Computer 3. Remove the bay cover 8 . Figure 6 - 9 RAM Cover Removed 8 6 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 9 & 10 ) in Figure 6 - 10.
Upgrading The Computer 5. The RAM module will 11 pop-up, and you can remove it. Figure 6 - 11 RAM Removal 11 6 6. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 7. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 8.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Unauthorized tampering with the HDD may also violate your warranty. 6 - 12 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains the information on the optional modules which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • Mini-PCI WLAN Module Bluetooth Module PC Camera Module Port Replicator Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Mini-PCI WLAN Module If you have included an MSI 6833 (802.11g) Mini-PCI WLAN module in your purchase option, you will have the appropriate software CD provided for your module. Before installing the MSI 6833 (802.
Modules & Options MSI 6833 WLAN Driver Installation 1. Make sure the WLAN module is powered ON. 2. Insert the Wireless LAN CD-ROM into the CD/DVD drive. 3. The program will run automatically. 4. Click Install Software (button) and click Next. 5. Click the button to accept the license agreement, then click Next. 6. Click Next > Install. 7. Click Finish. 8. The network settings can now be configured. 9.
Modules & Options Changing the Control Setting in WinXP The operating system is the default setting for wireless LAN control in Windows XP. It is recommended that you switch to use the WlanUtility to control your WLAN connection. 1. 2. 3. 4. 7 5. Right-click the WLAN icon in the taskbar and click Open Network Connections. Click to select the Wireless Network Connection and then click “Change Settings of the connection” (or right-click it and scroll to select properties). Click Wireless Networks (tab).
Modules & Options Figure 7 - 1 Switching WLAN Controls 7 Mini-PCI WLAN Module 7 - 5
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F12 key combination to toggle power to the optional Bluetooth module, and check the indicator to see if the module(s) is powered on or not (see Table 1 - 3, on page 1 9/Table 1 - 5, on page 1 11).
Modules & Options User Guide View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.
Modules & Options Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the BisonCam, NB Pro icon. . 7 PC Camera Module If you have included an PC Camera module in your purchase option, you will have the appropriate software CD provided for your module. Before installing the PC Camera driver, make sure that the optional PC Camera is on.
Modules & Options Sertek PC Camera Driver Installation 1. Press the Fn + F10 key combination to power on the PC Camera module (click Cancel if you see a “New Hardware Found” message). 2. Insert the PC Camera CD-ROM into the CD/DVD drive. 3. The program will run automatically. 4. Click Install Products. 5. Choose the language you prefer and click OK. 6. Click Next (click Continue Anyway if asked if you want to continue). 7. Click Finish to restart the computer. 8.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 7 Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Modules & Options Figure 7 - 3 Audio Setup (Windows XP) 7 PC Camera Module 7 - 11
Modules & Options Pre-Allocating File Space You may pre-allocate the file size for the capture file in the BisonCap program. You can choose to ignore this by clicking Cancel. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. You may find it helpful to defragment the HDD before capture.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options Port Replicator AC/DC Adapter You will be provided with a 90W AC/DC adapter if you purchase the port replicator option. 7 If you are using the computer with the Port Replicator, then you must use the 90W AC/DC adapter to power the port replicator and computer (DO NOT USE the computer’s 65W AC/DC adapter to power the Port Replicator).
Modules & Options Port Replicator Setup Instructions: 1. 2. 3. 4. 5. 6. 7. 8. Turn the computer OFF. Attach the Port Replicator’s external monitor cable to the external monitor port on the rear of the computer. Attach the Port Replicator’s power cable to the DC-In jack on the right of the computer.
Modules & Options Port Replicator Serial (COM) Port Driver 1. Insert the provided Port Replicator CD into the computer’s CD/DVD drive. 2. Click Start (menu) > Run... and navigate (Browse...) to D:\PL-2303 Driver Installer\PL-2303 Driver Installer.exe and click OK. 3. Click Next > Finish. 7 Port Replicator Network (LAN) Driver 1. Attach the Port Replicator as per the instructions in “Port Replicator Module” on page 7 - 14. 2. Insert the provided Port Replicator CD into the computer’s CD/DVD drive. 3.
Modules & Options 6. Click "+" next to Other devices (if its sub-menu items are not shown). 7. Double-click AX88772 and click Driver (tab). 8. Click Update Driver (button). 9. When the Hardware Update Wizard appears select “No, not this time” then click Next. 10. Click “Install from a list or specific location (Advanced)” then click Next. 11. Select “Search for the best driver in these driver in these locations.” and select ONLY “include this location in the search:”. 12. Navigate (Browse...
Modules & Options 7 7 - 18
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Power Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 15). Make sure you’re using the correct adapter.
Troubleshooting Display Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see “Sleep Button” on page 3 - 8). The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls. The computer is set for a different display.
Troubleshooting Boot Password Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning 8 If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Audio & CD Device Problem Possible Cause - Solution The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features” on page 2 - 12) to adjust. The compact disc cannot be read. The compact disc is dirty. Clean it with a CD-ROM cleaner kit. The compact disc tray will not open when there is a disc in the tray.
Troubleshooting Keyboard Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - 9). Other Keyboards 8 If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Troubleshooting Operation Problem Possible Cause - Solution The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “System Power Options” on page 3 - 6).
Troubleshooting Modules 8 Problem Possible Cause - Solution The Wireless LAN/ Bluetooth modules cannot be detected. The modules are off. Check the LED indicator to see if the WLAN/Bluetooth module is on or off (see “LED Indicators” on page 1 - 9). If the LED indicator is off, then press the Fn + F11 (WLAN) or Fn + F12 (Bluetooth) key combination(s) in order to enable the modules (see “Function Keys” on page 1 - 11). The PC Camera modules cannot be detected. The module is off.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Built-In Microphone Card Reader Port DC-In Jack Description The built-in microphone allows you to record on your computer The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. Plug the supplied AC/DC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Microphone-In Jack RJ-11 Phone Jack RJ-45 LAN Jack Description Plug an external microphone in to this jack to record on your computer. This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) Optional Port Replicator Ports and Jacks Item DC-In Jack Description Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD (see “Display Devices” on page B - 5). Parallel Port Connect a parallel type printer to this port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 6
Video Driver Controls Appendix B: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 17. VIA Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Instructions for installing the video driver are repeated below. 1. Click 2.Install Video Driver > Yes from the Drivers Installer menu. OR Navigate (Browse..) to D:\Drivers\Video\setup.
Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. B Advanced Video Controls This section is about making adjustments for the LCD, and switching display devices. The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 17.
Video Driver Controls S3Tray Plus Utility When the video driver is installed the S3TrayPlus utility will appear in the taskbar. Click/Right-click the icon to bring up the menu below. From this menu you will also be able to make display adjustments, access the Display Properties control panel, check video memory information etc.
Video Driver Controls S3 Display Control Panels The S3 Display control panels can be accessed from the S3Tray Plus utility in the taskbar, or from the Advanced tab in the Display Properties control panel. Figure B - 2 S3 Control Panels Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. B Click the “What’s This?” button to bring up a help menu (if the item has a help menu associated with it).
Video Driver Controls Display Devices Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel display as your display device. Connect it to the external monitor port at the rear of the computer. See the instructions below: S3Tray Plus Utility You can also use the S3Tray Plus Utility in the taskbar to configure an external display. Attach the external display (CRT) to the external monitor port. Right-click the icon in the taskbar and select S3Display. 1. 2. 3. 4. 5. 6.
Video Driver Controls Function Key Combination Display Modes Single Display Only one of your attached displays is used. You can use the Fn + F7 key combination to toggle through the display options: Multi-Monitor Mode This display mode simply shows an exact copy of the Primary display desktop on the Secondary display(s).
Video Driver Controls To Enable Extended Desktop (Display Properties) 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.
Video Driver Controls B B - 8
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor C Specification Intel Pentium® M Processor (478-pin) Micro-FC-PGA Package Models 730/ 740/ 750/ 760/ 770/ 780 (µ0.09) 0.09 Micron Process Technology 2MB On-die L2 Cache & 533MHz FSB 1.6/ 1.73/ 1.86/ 2/ 2.13/ 2.26 GHz Intel Celeron® M Processor (478-pin) Micro-FCPGA Package Models 350/ 360/ 370/ 380/ 390 (µ0.09) 0.09 Micron Process Technology 1MB On-die L2 Cache & 400MHz FSB 1.3/ 1.4/ 1.5/ 1.6/ 1.
Specifications Feature Specification Video Adapter VIA PN800 Integration Shared Memory Architecture of up to 64MB of Dynamic Video Memory Allocation Supports Analog Monitor Pixel Resolution up to 1920 * 1400 Integrated 128 bit 3D Graphics Engine Accelerator Supports Dual View for 2 Displays Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C 6 for drive options) Easy Changeable 2.5" 9.
Specifications Feature Specification Interface Three USB 2.0 Ports One External Monitor Port One Headphone-Out Jack One Microphone-In Jack One Line-In Jack One S/PDIF Output Jack One RJ-11 Jack for Plug & Play Fax/Modem One RJ-45 Jack for 10Mb/ 100Mb Fast Ethernet One DC-in Jack Card Reader Embedded 4-in-1 Card Reader (MS/ MS PRO/ SD/ MMC) Communication 10Mb/ 100Mb Fast Ethernet (Optional) 802.11g Mini-PCI Wireless LAN Module (Factory Option) AZALIA 56K Plug & Play Fax/Modem V.
Specifications Feature Power Specification Full Range AC/DC Adapter 20V, 3.25A (65 Watts), 100~240V, 47~63Hz Full Range AC/DC Adapter 20V, 4.5A (90 Watts), 100~240V, 47~63Hz (If Using the Optional Port Replicator) 6 Cell Smart Lithium-Ion Battery Pack, 4000mAH (44.4W) OR 6 Cell Smart Lithium-Ion Battery Pack, 4400mAH (48.8W) Environmental Spec Temperature Operating: Non-Operating: Physical Dimensions & Weight Model A Computers: 333mm (w) * 276mm (d) * 24-33mm (h) 2.
Specifications Feature Optional Specification Optical Drive Module Options: DVD-ROM Drive Module DVD/CD-RW Combo Drive Module DVD-Dual Drive Module 802.11g Wireless LAN Module with Mini-PCI Interface (Factory Option) 56K Plug & Play Fax Modem V.90 / V.92 Compliant Port Replicator (10/100Mb Base-T Ethernet Port, 4 * USB 2.0 Ports, Serial Port, Parallel Port, External Monitor Port, DC-In Jack) (Note: Port Replicator requires the supplied 90W power adapter) Charger Box (Factory Option) 300K or 1.
