ProStalk PC2000 Nature Camera User Manual
ES Index 1. Introduction ....................................................................................................................... 3 2. Camera Specifications ........................................................................................................ 4 3. Parts Identification............................................................................................................. 5 4. Packing Contents........................................................................
ES Main Features: 2.
ES Photo Taken Delay 5 second ~ 60mins (default 1 min) Selectable Image Resolution 2.0MP; 0.8MP Multiple Frame (Take 3 photos) Yes Video Resolution Movie: AVI 640 x 480 pixels @ 30 fps (15 seconds). File Format (Image/Video) JPEG/AVI Date Time Imprint Yes Moon Phase Imprint Yes Exposure Auto White Balance Mode Auto Menu Languages English Power Supply 4 x AA Cell batteries Camera Socket Yes Water Resistant Yes 3.
ES 4. Packing Contents Model ProStalk Digital Scouting Camera • User Manual • USB cable • Mounting Kit 5. Battery and SD Card Installation The ProStalk Digital Nature Camera is designed to operate using 4 x AA Cell Battery. We recommend using alkaline batteries. NOTE: Always have camera in OFF position when installing or removing batteries. ▲ Please make sure the voltage and polarity (+/-) are correct before connection. Incorrect voltage or polarity (+/-) will damage the camera.
ES Memory The ProStalk PC2000 Digital Nature Camera saves images to an SD memory card (accepting up to a 32GB SD card - sold separately). Inserting SD card Make sure camera is in the OFF position whenever adding or removing memory. • Insert SD memory card in to the SD card slot entirely and in the correct direction as shown by the sticker located at the side of the housing. • To remove the SD memory card, depress the SD card and pull out the card gently.
ES 1. 2. 3. 4. 5. 6. 7. Date Time 4 Digits Display Image Resolution Select Movie Recording Camera Delay Setting SD Card It is very easy to setup this camera. Turn on the unit and then press the “SETUP” button, the “DATE” icon will start to blink, press “UP” or “DOWN” to navigate the setup menu. Press the “OK” button to enter the specific menu item which is blinking. Use the “UP” or “DOWN” buttons to make adjustments. After the setting is done, press “SETUP” to save and exit the menu setting status. 6.
ES 6.2 Set Camera State and Photo Resolution To set the number of pictures or movie the camera will take per PIR triggering, the user can choose 1P, 3P or movie mode. a) Turn on the unit and press the “SETUP” button b) The menu icon will start to blink, press the “UP” or “DOWN” button till icon 4,5 is blinking, press “OK” to enter. c) Press the “UP” or “DOWN” button to select picture or movie.
ES 2) Set Time a) Turn on the unit and then press the “SETUP” button b) The menu icon will start to blink, press the “UP” or “DOWN” button until icon 2 “TIME” is blinking, press “OK” to enter. c) Then the LCD first two digits represent hour (HH) and last two digits represents minutes (MM). d) Press “UP” or “DOWN” to select hour between 00-23, Press “OK” to confirm. Then it comes to minutes setting. e) Press “UP” or “DOWN” to select minute between 00-59, Press “OK” to confirm.
ES a) Insert the strap through the strap slots on the rear housing. b) Wrap the strap around the mounting surface. Secure the strap and tighten the buckle in order to secure the camera. ▲ In order to obtain proper weather resistance, please make sure that both door latches are securely locked in place. 7.2 Turn on the Camera Then, just turn on the power switch and the camera is ready to take pictures. When the PIR sensor is trigged, it will start to take photos right after the delay time is passed. 7.
ES ▲ Make sure to switch the “Power” to “On” and press the "SETUP" button again after setting is over. Otherwise the camera will not take any pictures or movies. 7.4 Secure Your Camera The ProStalk PC2000 Nature Camera has a lock hole to secure the device using a padlock. 7.5 Replacing the Battery If the battery is low, the red light indicator will flash 3 times and then turn off. This indicates that the user should replace a new set of batteries.
ES 8. Viewing the Images and Movies Connect the Camera to PC directly 1. Sliding the “Power” toggle switch to “on” position 2. Press “SETUP” button 3. Connect your camera to the PC by the USB cable, the PC will recognize the new device and enter into “mass storage” mode. It will display a new disk symbol in your “file explorer”. The CD will display “STO” means the camera is in mass storage mode. 4. Then the user can copy, move or delete the photos and videos that are on the SD card.
ES 10. Glossary PIR: Passive Infrared Sensor. Senses motion like typical security motion detector. Requires infrared energy (heat) in addition to motion to trip the sensor to assure detection of live animals. Camera Delay: Time elapsed between photos while events are sensed and recorded. This is user-set based on wildlife activity in area. Resolution: The resolution selection that you have selected. MP = Mega Pixels = 1 million pixels HI (1600 x 1200): 2.0M pixels image.
