AS 2001- Allpro ORIGINAL INSTRUCTIONS Read the installation and operating instructions carefully before using the machine. Usage that is not in accordance with the instruction manual and/or disregard safety instruction, may cause injury or death, and damage the machine.
Installation instructions 1. Unpacking and installation: Open the transportation box by unscrewing the locks on both sides of the transportation box. 2. Place the machine on a steady table on a height between 80-100 cm. 3. Cut all cable ties. 4. Plug the power cord of the machine and vacuum cleaner. Place the NDT3 diamond tool to the diamond holder. 5. Use the machine in a warm, dry and well lit room. 6.
4. Guard against electric shock. Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges, refrigerators) 5. Keep other persons away. Do not let persons, especially children, not involved in the work touch the machine or the extension cord and keep them away from the work area. Make workshop kip proof with padlocks, master switches, or by removing starter keys. Do not overreach. Keep proper footing and balance at all times. Do not stand on the machine. 6.
Control Panel Manual page 4
Designation ProSharp AS 2001-Allpro is a skate sharpening machine and should be used only to sharpen ice skates. Safety Information and Recommendations Before using the machine check the grinding wheel for cracks. If there are cracks in the wheel (can be caused in transport), change the wheel to a new wheel before grinding. The skate sharpening machine AS 2001 may only be used for grinding skates.
= Never lay your hands on the machine when the sharpening procedure is on! Connection Connect tab single-phase A.C, 100-240 VAC 50-60 Hz. Release the emergency button. All lights flashing = put in a skate Lights are walking 1 by 1, machine is ready to sharp. Connect the dust-cleaners hose to the machine for automatic start of dust-cleaner when grinding. Connect dust-cleaners hose with the machines hose.
The ProSharp AS 2001- Allpro delivery includes: 1 Skate Sharpening Machine ProSharp AS 2001- Allpro 1 Grinding wheel MA70 1 Dressing-tool NDT3 7 Contouring templates 1 Power cord 1 Key for grinding wheel change, 19mm 2 Keys for the use of the emergency button 1 Transportation-box 1 Operating instruction manual Technical Data Voltage 1 x 100-240 VAC Cycles 50-60 Hz Power Pmotors: 300W, Poutlet: 200W, Ptotal: 2300W Power outlet for the vacuum cleaner MAX 2000W Weight 48k
FINLAND T. +358 40 5309 392 E. raimo@prosharp.net Maintenance Instructions Change of the grinding wheel and all service work may only be done when the main power is switched off. Before every grinding: Please check that: 1. You have read and understood the safety instructions and all functions. 2. The grinding wheel is OK, dust-cleaner is connected and that the motor is running without vibrations. After grinding: Lock the machine and take the key away.
Test run without grinding until there is no slippage. After 3000-5000 pairs: (1-2 seasons) Service should be made by an authorized service technician.
Dressing of the grinding wheel 1. When dressing the grinding wheel always adjust the grinding wheel sideways to position 3.0 mm. See Picture 1. Never put the skate in place when you are Picture 1. dressing the grinding wheel. 2. Choose the hollow by moving the skate-holder device by using the arrows from “SPEED” so that the “pointer” points on the hollow you wish to have. See Picture 2. Picture 2. 3.
Grinding. 1. Check the desired hollow radius and adjust if needed. Referring to the dressing of the grinding wheel. (Page 9.) 2. Adjust the grinding wheel sideways to the right blade thickness. (Picture 5.) Always remember to measure both blades because there are sometimes differences even between the blades in the same pair! HTC-tool is perfect for this! Picture 5. 3.
b. Use a flat template to set a correct height on the heel of the blade so that the grinding wheel will not make the heel rounded. Then by pressing the “SHARP” button start the grinding. Push the button again to turn the skate-holder device back just before the toe-picks of the skate. Repeat as many times as needed for the best grinding result. See also instructions of gliding surface profiling from page 11. c. Usage of the points in the skate-holder device.
8. Important! If you wish to reset the grinding push quickly 2 times the “SHARP” button when the skate-holder is going from left to right. When the skate- holder is moving from right to left only one push is needed for “reset”. Never start the machine without a skate unless you are dressing the grinding wheel! 9. Check the result and the skate is finished. For more detailed instructions how to use the electronics and adjustments please take a look at the electronics manual (Page 4.
rotates over the whole template the skate has been profiled from the whole (chosen) length of the blade. 7. Radius profiling. Choose a radius template and put the template into the right position. Adjust the guide-roll so that it will profile the desired surface of the blade. At least 50% of the blade from the middle should be profiled. Follow the points 5 & 6 to see how the grinding wheel will run against the blade. 8. Choose the desired blade profiling distance by using the “points” on the skateholder.
Change of the grinding wheel Changing of the wheel and all service work may only be done when the main power is switched off. But before switching the power off please read these instructions. Drive the skate-holder to the left by using the arrows at “SPEED” . Now switch the power off. 1. Adjust the wheel towards you by turning the “blade-thickness” nut 5 full rounds clockwise. See Picture 12. Now the nut is getting more accessible. Picture 12. 2.
