ORIGINAL INSTRUCTIONS • ProSharp AS2001 Allpro • ProSharp AS1001 Portable • ProSharp Skatepal Pro3 1
All operators must read and understand original instructions regarding operation and maintenance contained in this manual before using the machine. Usage that is not in accordance with the instruction manual and/or disregard safety instruction, may cause injury or death, and damage the machine. www.prosharp.com INDEX AS2001 ALLPRO.................................................................. 4 Installation instructions.....................................................................................
AS1001 PORTABLE.............................................................18 Installation instructions.................................................................................................. 19 Safety precautions......................................................................................................... 19 Control Panel Manual.....................................................................................................
AS2001 ALLPRO 4
1. Unpacking and installation: Open the transportation box by unscrewing the locks on both sides of the transportation box. 2. Place the machine on a steady table on a height between 80-100 cm. 3. Cut all cable ties. 4. Before using the machine do an ocular inspection and check the grinding wheel for any cracks which may have been caused by the transportation. 5. Plug in the power cord. 6. Turn the main switch on and turn the emergency stop button on with the attached key. 7.
. Never leave the machine running unattended. Press down the emergency switch, remove the key and disconnect all cables after using the machine. 7. Do an ocular inspection of the machine and look for any damages made from transportation. 8. Store the machine properly in a dry locked-up place, out of reach of children. 9. Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges. Always use the original cable delivered with your machine. 10.
AS2001 Allpro CONTROL PANEL MANUAL 7
EXPLANATION OF SYMBOLS MARKED ON THE SKATE SHARPENER PROSHARP AS 2001 ALLPRO = Always use mouth and breathing protection. = Always use ear protection. = Always use protective eye glasses. = Beware of electric shock! = Never lay your hands on the machine when the sharpening procedure is on. = Beware of rotating grinding wheel. = Read the original instructions carefully before using the skate sharpener.
AS2001 Allpro THE PROSHARP AS 2001 ALLPRO DELIVERY INCLUDES: • 1 Skate Sharpening Machine ProSharp AS 2001-Allpro • 1 Grinding wheel MA70 • 1 Dressing-tool NDT3 • 10 Contouring templates • 1 Power cord • 1 19mm wrench for grinding wheel change • 2 Keys for the use of the emergency button • 1 Transportation-box • 1 Operating instruction manual TECHNICAL DATA • Voltage Single-phase A.
MAINTENANCE INSTRUCTIONS Change of grinding wheel may only be done with the main power turned off. Before every grinding: Please check that: 1. You have read and understood the safety instructions and all functions. 2. Dust cleaner is connected. After grinding: Lock the emergency button and take away the key. Clean the machine from dust with a dust-cleaner and use a dry rag to clean up. Never use oil or grease. After 1-10 pairs: Dress the grinding wheel.
AS2001 Allpro DRESSING OF THE GRINDING WHEEL WITH REGULAR HOLLOW 1. Make sure that the scale-knob is set at 3.0 2. Choose your hollow and move the skate-holder by using the arrows on the controlpanel 3. The hollow radius sticker on the skate-holder indicates which hollow you want to dress. Once set, lock the wheel arm. 4. Adjust the diamond tool downwards until it barely touches the surface of the grinding wheel. 5.
DRESSING OF THE GRINDING WHEEL WITH CHANNEL Z When you choose to make a radius hollow combined with a channel, choose first the hollow radius, and follow instructions how to dress. Once dressed, let the wheel arm be locked and turn the knob on the dress units handle to its lower position. Choose S, M or L width of the channel by screwing the Channel Z -thumbscrew in or out to make the tap on the diamonds handle hit it. Follow the scale to see what width you get. 1.
AS2001 Allpro GRINDING OF FIGURE SKATES AND BANDY SKATES 1. After dressing your grinding wheel, measure your skate and set the scale knob on the same width as your skate. 2. Clamp the skate in to the skate-holder. The toe of your skate should always point to your left. 3. Loosen the two nuts on the Figure skate device and slide it as far to your right as possible and tighten the nuts. (Take notice that the adjustment screw has to be located under the figure skate device). 4.
PROFILING 1. Choose a profiling template and clamp it to the template holder. 2. Measure the area of your skate that you would like to profile and mark up the blade. Use the toe-pitch-heel sticker to help you. Always profile at least 60% of your skate. 3. Clamp the skate to the skate holder. 4. Push the ”Profile” button once and a light will start to blink. Now press the ”Sharp” button and the sledge will start to moving without the grinding wheel spinning. 5. Adjust the guide-roll´s height.
Changing of the wheel may only be done when the main power is switched off. But before switching the power off please read these instructions. 1. Move the skate-holder to the left using the arrows on your control-panel. 2. Now remove the cover and use the 19mm wrench and loosen the nut. 3. Remove the wheel and replace it with a new one. (the label on the wheel should point towards the front on the machine). 4. Tighten the nut and put the cover back on. 5.
WARRANTY The warranty applies for one year for materials and workmanship. The manufacturer is not responsible for defects or faults that arise from normal usage, negligent maintenance or other neglect, unauthorized tampering, improper use, service or repairs performed by others than those approved by the manufacturer, as well as variations in electrical voltage or other electrical disorders.
AS2001 Allpro
AS1001 PORTABLE 18
INSTALLATION INSTRUCTIONS 1. Unpacking and installation: Open the transportation box by unscrewing the locks on both sides of the transportation box. 2. Place the machine on a steady table on a height between 80-100 cm. 4. Before using the machine do an ocular inspection and check the grinding wheel for any cracks which may have been caused by the transportation. 5. Plug in the power cord. 6. Screw the diamond tool into the dress unit. 7.
6. Never leave the machine running unattended. Press down the emergency switch, remove the key and disconnect all cables after using the machine. 7. Do an ocular inspection of the machine and look for any damages made from transportation. 8. Store the machine properly in a dry locked-up place, out of reach of children. 9. Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges. Always use the original cable delivered with your machine. 10.
CONTROL PANEL MANUAL AS1001 Portable 21
EXPLANATION OF SYMBOLS MARKED ON THE SKATE SHARPENER PROSHARP AS 1001 PORTABLE = Always use mouth and breathing protection. = Always use ear protection. = Always use protective eye glasses. = Beware of electric shock! = Read the original instructions carefully before using the skate sharpener. = Beware of rotating grinding wheel.
THE PROSHARP AS 1001- PORTABLE DELIVERY INCLUDES: • 1 Skate sharpening machine ProSharp AS 1001-Portable • 1 Grinding wheel MA70 • 1 Dressing-tool NDT3 AS1001 Portable • 1 Power cord • 1 19mm wrench for grinding wheel change • 2 Keys for the use of the emergency button • 1 Transportation-box • 1 Operating instruction manual TECHNICAL DATA • Voltage Single-phase A.
MAINTENANCE INSTRUCTIONS Change of grinding wheel may only be done with the main power turned off. Before every grinding: Please check that: 1. You have read and understood the safety instructions and all functions. 2. Dust cleaner is connected. After grinding: Lock the emergency button and take away the key. Clean the machine from dust with a dust-cleaner and use a dry rag to clean up. Never use oil or grease. After 1-10 pairs: Dress the grinding wheel.
DRESSING OF THE GRINDING WHEEL WITH REGULAR HOLLOW 1. Make sure that the scale-knob is set at 3.0 3. The hollow radius sticker on the skate-holder indicates which hollow you want to dress. Once set, lock the wheel arm. 4. Adjust the diamond tool downwards until it barely touches the surface of the grinding wheel. 5. When you choose to make a regular hollow make sure the knob on the dress units handle is lifted and locked in the upper position. 6. Push the “DRESS” button on the control-panel once.
DRESSING OF THE GRINDING WHEEL WITH CHANNEL Z When you choose to make a radius hollow combined with a channel, choose first the hollow radius, and follow instructions how to dress. Once dressed, let the wheel arm be locked and turn the knob on the dress units handle to its lower position. Choose S, M or L width of the channel by screwing the Channel Z -thumbscrew in or out to make the tap on the diamonds handle hit it. Follow the scale to see what width you get. 1.
GRINDING OF FIGURE SKATES AND BANDY SKATES ALTERNATIVE 1: Sharpening with the Figure Skate Device. AS1001 Portable 1. After dressing your grinding wheel, measure your skate and set the scale knob on the same width as your skate. 2. Clamp the skate in to the skate-holder. The toe of your skate should always point to your left. 3. Loosen the two nuts on the Figure skate device and slide it as far to your right as possible and tighten the nuts.
GRINDING OF FIGURE SKATES AND BANDY SKATES ALTERNATIVE 2: 1. After dressing your grinding wheel, measure your skate and set the scale knob on the same width as your skates. 2. Put your toe pick on any of the profiling dots on the skate holder. Then clamp your skate. Click on the ”PROFILE” button on your control-panel. Here you have three options. Each light indicates where the skate-holder will turn back.
CHANGE OF THE GRINDING WHEEL Changing of the wheel may only be done when the main power is switched off. But before switching the power off please read these instructions. 1. Move the skate-holder to the left using the arrows on your control-panel. 3. Remove the wheel and replace it with a new one. (the label on the wheel should point towards the front on the machine). 4. Tighten the nut and put the cover back on. 5.
WARRANTY The warranty applies for one year for materials and workmanship. The manufacturer is not responsible for defects or faults that arise from normal usage, negligent maintenance or other neglect, unauthorized tampering, improper use, service or repairs performed by others than those approved by the manufacturer, as well as variations in electrical voltage or other electrical disorders.
AS1001 Portable
SKATEPAL PRO3 32
UNPACKING AND INSTALLATION 1. Place the machine on a steady bench with a work height between 80-100 cm. 2. Open the top lid by clicking on the buckles on each side of the machine. 3. Inside the lid you will find the power cord and the vacuum extension. 4. Move the slide lid found on the right end of the machine and connect the vacuum extension to it. 5. Connect the power cord and turn on the switch. 6. Use the machine in a warm, dry and well lit room.
8. Store the machine properly in a dry locked-up place, out of reach of children. 9. Never yank the cord to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges. Always use the original cable delivered with your machine. 10. Avoid unintentional starting. Ensure switch is in “off” position when plugging in your power cord. 11. This machine should only be repaired by an authorized service representative using only original spare parts. 12.
= Always use mouth and breathing protection. = Always use ear protection. = Always use protective eye glasses. = Beware of electric shock! Skatepal Pro3 EXPLANATION OF SYMBOLS MARKED ON THE SKATE SHARPENER PROSHARP AS 2001 ALLPRO = Read the original instructions carefully before using the skate sharpener. From left to right: 1. Wheel pressure adjustment. 2. Adjustment of grinding wheel sideways.
BUSINESS NAME AND MANUFACTURER AUTHORIZED SERVICE REPRESENTATIVE Eriksson Teknik AB ProSharp AB Hirsvägen 4 Hirsvägen 4 86241 Njurunda 862 41 Njurunda SWEDEN SWEDEN T. +46 60 15 85 80 T. +46 60 15 85 80 F. +46 60 15 83 80 E. support@prosharp.com E. order@prosharp.com TECHNICAL DATA • • • • • • • • Voltage Power Cycles Weight Width Length Height Noise level AC INPUT 100-240 VAC 3.6A 150W 50/60hz 32.6 lbs (14.
MAINTENANCE INSTRUCTIONS • Control and clean the machine daily after the usage, and always after every 30 pairs of skates. • Remove the plug before carrying out any adjustment, servicing or maintenance. • After 1-3 years or around 10,000~ cycles, service should be made by an authorized service technician. GRINDING WHEELS Every B64 wheel lasts around 1000~ cycles Change the grinding wheel according to the instructions.
SHARPENING 1. Put the skate in the machine with the toe to the left. Clamp it with the clamp handle located to your right. 2. Press the black start/stop button located on the machines right side. Each push equals 1 cycle. You may sharpen up to 5 cycles at a time. 3. Unclamp the skate and check result. SHARPENING FIGURE SKATES • To sharpen figure skates you need a round toe pick protector. Its designed to protect the toe picks on your figure skate.
Skatepal Pro3
ProSharp AB Tel office: +46 60 15 85 80 Hirsvägen 4 E-mail: support@prosharp.com S-862 41 Njurunda 40 Sweden Website: prosharp.
