ProSharp AS 1001 ORIGINAL INSTRUCTIONS Read the installation and operating instructions carefully before using the machine. Usage that is not in accordance with the instruction manual and/or disregard safety instruction, may cause injury or death, and damage the machine.
Installation instructions 1. Unpacking and installation: Open the transportation box by unscrewing the locks on both sides of the transportation box. 2. Place the machine on a steady table on a height between 80-100 cm. 3. Cut all cable ties. 4. Plug the power cord of the machine and vacuum cleaner. Place the NDT3 diamond tool to the diamond holder. 5. Use the machine in a warm, dry and well lit room. 6. After usage of the machine clean the machine and the working space properly.
workshop kip proof with padlocks, master switches, or by removing starter keys. Do not overreach. Keep proper footing and balance at all times. Do not stand on the machine. 6. Never leave tool machine running unattended. Turn power off. Don’t leave tool until it comes to a complete stop. 7. Use right tool. Do not use the tool for purpose not intended. Don’t force the machine. It will do the job better and safer at the rate for which it was designed. 8. When not in use always disconnect the power cords. 9.
Control Panel Manual Page 4
Designation ProSharp AS 1001-Portable is a skate sharpening machine and should be used only to sharpen ice skates. Safety Information and Recommendations Before using the machine check the grinding wheel for cracks. If there are cracks in the wheel (can be caused in transport), change the wheel to a new wheel before grinding. The skate sharpening machine AS 1001 may only be used for grinding skates. Only original special balanced ProSharp grinding wheels may be used in the machine.
Connection Connect tab single-phase A.C, 100-240 VAC 50-60 Hz. Connect the dust-cleaners power cord to the side of the machine for automatic start of dustcleaner when grinding. Connect dust-cleaners hose to the machine. Placement The machine must be placed on a flat, steady workbench with a height between 80-100 cm. The working area must be well lit. Keep work area clear. Cluttered areas and benches invite injuries.
The ProSharp AS 1001- Portable delivery includes: 1 Skate sharpening machine ProSharp AS 1001-Portable 1 Grinding wheel MA70 1 Dressing-tool NDT3 1 Power cord 1 19mm wrench for grinding wheel change 2 Keys for the use of the emergency button 1 Transportation-box 1 Operating instruction manual Technical Data Voltage 1 x 100-240 VAC Cycles 50-60 Hz Power P motors: 200 W, P outlet 2000W, P total 2200W Power outlet for the vacuum cleaner MAX 2000W Weight 28 kg (including the
Maintenance Instructions Change of wheel and all service work may only be done when the main power is switched off. Before every grinding: Please check that: 1. You have read and understood the safety instructions and all functions 2. Dust cleaner is connected. After grinding: Lock the emergency button and take away the key. Clean the machine from dust with a dust-cleaner and use a dry rag to clean up. Never use oil or grease. After 1-10 pairs: Dress the grinding wheel.
Dressing of the grinding wheel with regular hollow 1. Make sure that the scale-knob is set at 3.0 2. Choose your hollow and move the skateholder by using the arrows on the control-panel 3. The hollow radius sticker on the skateholder indicates wich hollow you want to dress. Once set, lock the wheel arm. 4. Adjust the diamond tool downwards until it barely touches the surface of the grinding wheel. 5.
diamond tool since you have dressed the other side to avoid uneven edges). Now you successfully dressed the wheel with desired hollow and width of the channel. Grinding. 1. After dressing your grinding wheel, measure your skate and set the scale knob on the same width as your skates. 2. Clamp the skate in to the skate-holder. The toe of your skate should always point to your left 3. Choose number of grinding cycles by using the “SHARP” button.
Grinding of figure skates and Bandy skates Alternative 1: Sharpening with the Figure Skate Device 1. After dressing your grinding wheel, measure your skate and set the scale knob on the same width as your skates. 2. Clamp the skate in to the skate-holder. The toe of your skate should always point to your left. 3. Loosen the two nuts on the Figure skate device and slide it as far to your right as possible and tighten the nuts.
2. Put your toe pick on any of the profiling dots on the skate holder. Then clamp your skate. Choose from “PROFILE” from which point the skate-holder will turn back. See pictures 6 & 7. Two pushes one light will go on and the skate-holder will turn back from the “1 point mark”. 3 pushes 2 lights and the skate-holder will turn back from the “2 points mark”. 4 pushes 3 lights and the skate-holder will turn back from the “3 points mark”. 3. Choose number of grinding cycles by using the “SHARP” button.
Change of the grinding wheel Changing of the wheel and all service work may only be done when the main power is switched off. But before switching the power off please read these instructions. Drive the skate-holder to the left by using the arrows at “SPEED” . Now switch the power off. 1. Remove the cover, see picture 3, by loosing the screw to the right and take the cover away. 2. Adjust the wheel towards you by turning the scale knob nut 3 full rounds clockwise. See Picture 1.
Warranty The warranty applies for one year for materials and workmanship. The manufacturer is not responsible for defects or faults that arise from normal usage, negligent maintenance or other neglect, unauthorized tampering, improper use, service or repairs performed by others than those approved by the manufacturer, as well as variations in electrical voltage or other electrical disorders.
Page 15
Page 16
