4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
z IPsec Net-to-Net with RSA authentication result y Server y Client 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
VPN > GRE This section allows you to set GRE configuration. The default mode is off. Generic Routing Encapsulation (GRE) is one of the available tunneling mechanisms which uses IP as the transport protocol and can be used for carrying many different passenger protocols. The tunnels behave as virtual point-to-point links that have two endpoints identified by the tunnel source and tunnel destination addresses at each endpoint. The GRE Mode is on.
VPN > PPTP Server This section provides 2 sub configurations, including General Configuration and Clients Configuration. (1) General Configuration VPN > PPTP Server > General Item Description Mode Server Address Client Address Range Select from Off or On to enable PPTP Server. IP addresses to be used at the local end of the tunneled PPP links between the server and the client. A list of IP addresses to assign to remote PPTP clients.
4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
VPN > L2TP This section allows you to set up L2TP and provides three modes for configuration, including Off, Server, and Client Mode. (1) General Mode: The default mode is Off as shown in the following interface. (2) Server Mode: Choose the Server mode and the interface will be changed as below. Item Mode Auth Local IP Remote begin IP Remote end IP Username VPN> L2TP > Server Mode Description Select from Off or On to set the client setting. The authentication method for L2TP connection.
Password The L2TP client's password. Could be used to add the newly client or update existed client. Fill in the username and password and click the and manage them under server mode. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
(3) Client Mode: Choose the Client mode and the interface will be changed as below. Item Mode Server Auth Username Password NAT Default route VPN> L2TP > Client Mode Description Turn on/off this L2TP connection The L2TP server address or hostname. The authentication method for L2TP connection. Should same as L2TP server's auth type. The username for L2TP authentication. The password for L2TP authentication. Turn on to translate the LAN subnet IP to L2TP virtual IP.
Click the button and edit the parameters to update the L2TP connection. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Configuration > Firewall This section allows you to configure Basic Rules, Port Forwarding, DMZ, IP Filter, MAC Filter, URL Filter, NAT and IPS. Firewall > Basic Rules This section allows you to set the Basic Rules configuration. Firewall > Basic Rules Item WAN Ping Blocking Description Check IPv4 or IPv6 for blocking 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Firewall > Port Forwarding This section allows you to set up Port Forwarding and click 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.8 edit button to configure.
Firewall > Port Forwarding Item Description Description Turn on/off Port Forwarding to select Disable or Enable. The default is Disable. Descript the name of Port Forwarding. Protocol Select from UDP or TCP Client which depends on the application. Source Port Begin Fill in the beginning of source port. Source Port End Fill in the end of source port. Destination IP Fill in the current private destination IP. Destination Port Begin Fill in the beginning of private destination port.
Firewall > IP Filter This section allows you to configure IP Filter. After clicking button, you can edit your IP protocol, source/port and destination/port. The default is Disable mode and Black list. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
z Black List: When set as Black List, the specific IP address/port in rule will be blocked. z White List: When set as White List, the specific IP address/port in rule will be accepted. Management IP Address: For White List only. Since White List will block all user communication except those has been assigned by rules, it is better to assign a specific IP address for the administrator to access the Router which is Management IP Address. Service Ports: For White List only.
Edit Black/White List (1) Click button to edit Black/White list. (2) The default is Disable mode as the following interface (Black/White). 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Item Mode Protocol Source IP Source Port Destination IP Destination Port Firewall > IP Filter Description Select from Disable or Enable. The default is Disable. Select from All, ICMP, TCP or UDP. Fill in your source IP address. Fill in your source port. Fill in your destination IP address. Fill in your destination port. (3) When selecting Enable Mode, the protocol is TCP. The source IP has IPv4 and IPv6 setting formats.
Firewall > MAC Filter This section allows you to set up MAC Filter. After clicking address. Item Mode MAC Address button, you can edit your MAC Service > MAC Filter Description Select from Disable or Enable. The default is Disable. Fill in your MAC address. Note: Setting up MAC address, please use ”:” colon symbol (e.g. xx : xx : xx : xx) or “-“ hyphen symbol to mark (e.g. xx - xx - xx - xx). 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Firewall > URL Filter This section allows you to set up URL Filter. After clicking filter and information. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Note: Please not include “https://” or “http://” for the URL address in the Full Filter. Item Mode Filter Key / Full Firewall > URL Filter Description Select from Disable or Enable. The default is Disable. Select from Key or Full. The default is Key. Fill in your Key / Full information. Firewall > NAT This section allows you to set NAT configuration.
Firewall > IPS This section allows you to set IPS configuration. IPS prevents the system from being attacked by the Internet. The system allows to limit the max incoming connection number from WAN per source IP address to prevent system resource exhausted. Also, the system allows to limit the max incoming connection retry number during a specific time period from WAN per source IP address to prevent too many unexpected connections retry event from causing system busy.
Configuration > Service This section allows you to configure the SNMP, TR069, Dynamic DNS, VRRP, MQTT, UPnP, SMTP, and IP Alias. Service > SNMP This section allows you to set the SNMP configuration. 13.1.1 Community 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Service > SNMP > Community Item Description Mode Select from Disable or Enable to configure SNMP. Community Configure community setting with three options, including # 1, # 2 and #3. Mode Select from Disable or Enable. Name Name each community. Access Select from Read-Only or Read-Write. 13.1.2 SNMP v3 User Configuration For SNMP v3 User Configuration, you need to register authentication and allow a receiver that confirm the packet was not modified in transit.
Authentication Protocol Privacy Password Privacy Protocol Access 13.1.3 Select from MD5 or SHA. Fill in your privacy password. Select from DES or AES. Select from Read-Only or Read-Write. SNMP trap configuration This section allows you to set up the SNMP trap configuration when you select the SNMP trap function from Alarm output of system for your router. With SNMP trap setting, you can know the status of remote device.
Service > TR069 This section allows you to set up TR069 client configuration. You can get information how to install TR069 Server (GenieACS Installation) from the application configuration chapter. Item Mode ACS URL ACS Username ACS Password Periodic Inform Periodic Inform Interval (Sec) Connection Request Username Connection Request Password Connection Request Port Service > TR069 Description Select from Disable or Enable. The default is Disable.
Service > Dynamic DNS This section allows you to set up Dynamic DNS. Item Mode Service Provider Host Name Token ID Host Secret ID Username Password Update Period Time (Sec) IP Address Selection Service > Dynamic DNS Description Turn on/off this function to select Disable or Enable. The default is Disable. Select the Service Provider of Dynamic DNS. Fill in your registered Host Name from Service Provider. Fill in your Token ID from Service Provider. Fill in your Secret ID from Service Provider.
Note: There are six options of Service Provider as below to explain the information. Service Provider dynv6.com Host Name Register hostname, e.g. tester.dynv6.net Token ID The token ID, e.g. v_ABjMMQxeAnWv5UwtuVn1QBriynzq Service Provider www.nsupdate.info Host Name Register hostname, e.g. tester.nsupdate.info Host Secret ID The Host Secret ID, e.g. e2AMDsLmVF Service Provider www.duckdns.org Host Name Register hostname, e.g. tester.duckdns.org Token ID The token ID, e.g.
Service > VRRP This section allows you to configure VRRP. Item Mode Group ID Priority Virtual IP Service > VRRP Description Select from Disable or Enable. The default is Disable. Specify which VRRP group of this router belong to (1-255). The default is 1. Enter the priority value from 1 to 254. The larger value has higher priority. The default is 100. z Each router in the same VRRP group must have the same virtual IP address. The default is 0.0.0.0.
Item Mode Port Manage Users Username Password ACLs User Topic Service > MQTT Description Select from Disable or Enable. The default is Disable. Fill in the port number of MQTT application. Create the users and show all users’ names. Allow each user to delete their name. Fill in the username of manage user. Fill in the password of manage user. Allow to specify what topic should be limited. Select the users and identify their authority to read or write the MQTT topic/channel. Name the topic of MQTT message.
4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Service > UPnP This section allows you to set up UPnP confirguration to select the mode from Disable or Enable. The default UPnP is enabled for the cellular router. Note: UPnP™ (Universal Plug and Play) is a set of protocols that allows a PC to automatically discover other UPnP devices (anything from an Internet gateway device to a light switch), retrieve an XML description of the device and its services, control the device, and subscribe to real-time event notification.
Service > IP Alias This section allows you to set IP Alias configuration. IP Alias is associating more than one IP address to a network interface. With IP Alias, one node on a network can build multiple connections with the network, each serving a different purpose. IP Alias can be used to provide multiple network addresses on a single physical interface. Item Mode Entries Add / Edit IP Alias Entry Service > IP Alias Description Select from Off or On to enable the IP Alias.
Configuration > Management This section provides you to manage the router, set up your administration and know about the status of current software and firmware. Also, you can back up and restore the configuration. Management > Identification This section allows you to confirm the profile of router, current software, firmware version and system uptime. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Management > Identification Item Description Model Name The model name of cellular router. LAN Ethernet MAC Address The LAN Ethernet MAC address. WAN Ethernet MAC Address The WAN Ethernet MAC address. Software Version The software version currently running on the device. Firmware Version The firmware version of the device. Hardware Version The hardware version of the device. Software MCSV Show the software MCSV of the running firmware Hardware MCSV Show the current hardware MCSV of the device.
ġ Management > Contacts / On Duty This section allows you to create the groups, add the usersFor more detailed instruction, please navigate to System > Alarm. 14.3.1 Contacts + Add Group: Please fill out group name. + Add User: Please fill out Name/Phone/E-Mail/Groups. 14.3.2 Duty Schedule Please select duty date for every group. The trust and responsible groups can control/receive alarms and SMS. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Management > SSH Secure Shell (SSH) allows user to configure system via a secure channel. User can configure system from either public domain or local LAN. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Item Mode LAN Server Port WAN Server Port Access Control Management > SSH Description Select from Disable or Enable SSH function. The LAN side TCP port number listened by SSH server. The WAN side TCP port number listened by SSH server. z Allow All: Any client who own the IPv4v6 Address can reach system is able to connect system. z Allow specified IPv4v6 Address below: Only those configured IPv4v6 Address client are allowed to connect system.
ġ Management > Restart This section allows you to click button and the router will restart immediately. Configuration > Diagnosis This section allows you to diagnose Ping and Traceroute for your Host (IP address or Domain Name). Diagnosis > Ping Please assign the Host you want to ping.
Diagnosis > Traceroute Please assign the Host **you want to** traceroute. The result of the traceroute is as below. Diagnosis > Ping Item Use Interface As Source Use Interface Host Description Use or not use the Interface as source APN1 / APN2 The host name or the host IP address 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Configuration Applications This section explains specific examples how to configure your applications. WAN Priority You can select from ETH First, LTE Only, ETH Only or LTE First. (1) WAN Priority > ETH First: In case both Ethernet and LTE can access Internet, the router would route network packages through Ethernet. The reason is Ethernet that is low price and stable.
(3) WAN Priority > ETH Only: In this mode, the router only routes network packages through Ethernet. (4) WAN Priority > LTE First: In case both Ethernet and LTE can access Internet, the router would route network packages through LTE. However, in case LTE is unplug or not able to access Internet (check by ping), the router would route network packages through Ethernet network. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
LAN > IPv4/IPv6 Dual Stack The router supports IPv4/IPv6 dual stack by default, it means IPv4 packages route to IPv4 network and IPv6 route to IPv6 network. Since IPv6 is global IP, there is no NAT between WAN site and LAN site. One device only needs one global IPv6. There is IPv6 firewall protection in the router by default. Only the IPv6 packages come from LAN site device and got reply back. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
The router automatically detects IPv6 environment and query IP. After the IP is obtained successfully, it will distribute to LAN site hosts. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
MQTT Broker The cellular router provides the MQTT broker feature which allow the MQTT client sending the message within specific topic (channel). By default, the cellular router does not allow anonymous to read/write the MQTT topic (channel). Thus, you need to create the account with username and password for MQTT client in the web UI. The Manage Users section will show all created users. Each user can use the delete button to delete it. For the ACL control, you can specify what topic should be limited.
For example, we set the publisher pub2 to write the critical topic. Additionally, we also the subscribers sub1 and sub3 can read the critical topic. Thus, when pub2 is sending the message only the sub1, the sub3 can receive it. Alarm Configuration After you enable alarm, all the selected alarm input events would trigger selected alarm output. (1) Alarm Input: z The alarm would be triggered when DI1/DI2 show(s) high signal.
(2) Alarm Output: z In case of SMS is selected then only user’s phone number is in selected group and on selected working day would receive alarm SMS. z In case of DO is selected, please make sure your DO is connected to your alarm device. z In case of SNMP trap is selected, please make sure you enable SNMP trap (Service -> SNMP) and fill our server IP. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Open VPN Configuration Generic setup For Open VPN configuration, use the certificate to authenticate the VPN connection. Thus, you need to generate the required files for Open VPN server or import the required file to Open VPN client. 16.5.1 Open VPN Server Mode Open VPN server certificate generation For the Open VPN server mode, the Open VPN web UI provides the buttons to generate the required files. The files include Root CA, Cert, Key and Open VPN client files.
And you can click the info button to show the detail for each files, or click the download button to download the file to PC. 16.5.2 Open VPN Client Mode Open VPN client certificate import For the Open VPN client mode, the Open VPN web UI provides the buttons to import the required files. The Open VPN client can use the Root CA, User Key and User Cert files from Open VPN server to authenticate the VPN tunnel. Or just only use the PKCS#12 (P12) file from Open VPN server to authenticate it.
16.5.3 Open VPN Net-to-Net You can use the Open VPN VPN tunnel to make the PC1 and PC2 communicate each other. (1) Open VPN server configuration For the Open VPN server side, the basic setting is as shown in below figure. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
The VPN Network and VPN Netmask are required fields. Note: The VPN Network should be network ID (e.g. 192.168.30.1 is invalid setting.) When PC1 and PC2 communicate each other, the Route Client Networks should be enabled. And add the LAN information of Open VPN client side, in this case the #1 route will be 10.0.0.0 and 255.255.255.0 Note: The #1 route means the routing information for User 1.
(2) Open VPN client configuration For the Open VPN client side, the basic setting is as below figure. The Server Address is required field, which indicate the Open VPN server address which Open VPN client try to connect. And the PKCS12 Password only works when selected the pkcs #12 Certificate authentication option. This option requires the P12 file which generated from Generic Setup Open VPN server part. The password also be set on the Generic Setup Open VPN server part.
16.5.4 Open VPN 1:1 NAT For the net-to-net part, the Open VPN server LAN network and the Open VPN client LAN network are different. But some time, the LAN network will be same for both sides. When this situation occurred, the routing rules will be ambiguous that will result in the PC1 and the PC2 can't communicate each other. Thus, the router Open VPN provides the 1:1 NAT feature. The feature will convert the conflict subnet to different subnet.
For the Open VPN client side, same as server side but we fill up the Network as 192.168.11.0. The setting will make router convert the Open VPN client side LAN network from 192.168.1.0/24 to 192.168.11.0/24 when the VPN traffic is coming. 16.5.5 Open VPN with third-party server A VPN enables you to send and receive data across shared networks. For some users, they will use the VPN to access the limited network service from the different country.
For example, use the Japan Open VPN server which provided by http://www.vpngate.net/en/. Firstly, download the ovpn configuration files from vpngate.net. Additionally, use the Open VPN custom import button to import it. The result is as the below figure. If the .ovpn configuration file is correct, the web UI will show Apply OK. If the third-party Open VPN server is reachable, the VPN tunnel will be established.
16.5.6 Install Open VPN Access Server on Docker Open VPN Access Server on Docker installation Open VPN Access Server is a full featured secure network tunneling VPN software solution that integrates Open VPN server capabilities, enterprise management capabilities, simplified Open VPN Connect UI, and Open VPN Client software packages that accommodate Windows, MAC, Linux, Android, and iOS environments.
Install Docker CE sudo apt-get update sudo apt-get install docker-ce Install Open VPN Access Server by docker image Reference: https://hub.docker.com/r/linuxserver/Open VPN-as/ sudo mkdir -p /Open VPN-as sudo docker create --name=Open VPN-as \ -v /Open VPN-as:/config \ -e TZ="Asia/Taipei" \ -e INTERFACE=enp3s0 \ --net=host --privileged linuxserver/Open VPN-as sudo docker start Open VPN-as Check the Open VPN Access Server by visiting https://:943 Setup Open VPN Access Server for Cellular
And switch to the User Permission page to create the user for Cellular Router. (In this case, we use the test/test to be the example.) 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Also check the Access from all other VPN clients to make the Cellular Router could be reachable. Setup Cellular Router Open VPN client 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Use the user test/test to login https://:943 Please make sure to change the type from Connect to Login. After logged, please download the .ovpn configuration by click the user-locked profile. Upload the .ovpn configuration to Cellular Router Open VPN custom mode, and input the username and password. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
When the VPN tunnel established, the Cellular Router can be managed/accessed by the other VPN clients. 16.5.7 Install Pritunl Open VPN server on Docker Pritunl Open VPN server on Docker installation Pritunl is a distributed enterprise vpn server built using the Open VPN protocol. Quick Installation Prerequisites z Ubuntu 16.04 z curl or wget should be installed Install via curl sh -c "$(curl -fsSL https://bit.ly/2IpJN1X)" Install via wget sh -c "$(wget https://bit.
sudo apt-get update sudo apt-get install \ apt-transport-https \ ca-certificates \ curl \ software-properties-common curl -fsSL https://download.docker.com/linux/ubuntu/gpg | sudo apt-key add sudo add-apt-repository \ "deb [arch=amd64] https://download.docker.com/linux/ubuntu \ $(lsb_release -cs) \ stable" Install Docker CE sudo apt-get update sudo apt-get install docker-ce Install Docker compose sudo apt-get install docker-compose Install Pritunl Open VPN Server by docker compose (1) Set up the basic envir
- "443:443/tcp" volumes: mongo: pritunl: (3) Run the command docker-compose up -d to start the server (4) Check the Pritunl Open VPN Server by visiting https:// Setup Pritunl Open VPN Server for Cellular Router The server will running on https://. The default username/password is pritunl/pritunl. Login Page: After logged, the server will ask you to do the initial setup. You can change the username and the password setting in this page.
Open VPN user setup Please navigate to the User page to setup the Open VPN user account. Add the organization by click the Add Organization button. (In this document, we use the MR to be the organization example.) When the organization be created, the Users page should be like the following figure. Then add the Open VPN user by click the Add User button. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Note: In this Open VPN server, the PIN must contain only digits. Note: In this document, we use the test/123456 Open VPN user to be the example. Open VPN server setup Please navigate to the Server page to setup the Open VPN server. And click the Add Server button to create the Open VPN server. Note: Please click the Advanced tab and make sure the Inter-Client Communication be checked 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
When the Open VPN server created, the Servers page should like the following figure. And click Attach Organization button to setup the Open VPN server. Start the Open VPN server by click Start Server button. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Cellular Router setup First, please navigate to the Users page and download the user configuration file and extract it. Note: In this document, you should get the MR_test_router.ovpn file. And visit the Cellular Router Open VPN custom page then import the .ovpn file. Fill up the username/password which be setup in Open VPN user setup part. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
When the Cellular Router Open VPN connected, the Pritunl Open VPN server also update the user status. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
VRRP Topology Basic VRRP Topology Base on this topology and VRRP Parameter settings, Router A and Router B will offer a virtual router service with virtual IP = 192.168.1.200 for the client. TR069 Server (GenieACS Installation)ġġ Server OS: Ubuntu 14.04 on Virtualbox Installation: 1) Login ubuntu 2) Change to root by 'su -' and enter your root password.
./configure make && make install ruby -v ruby 2.4.1p111 (2017-03-22 revision 58053) [i686-linux] cd /opt gem install rails --no-ri --no-rdoc gem install bundle --no-ri --no-rdoc 7) Install node.js cd /opt wget http://nodejs.org/dist/v8.2.1/node-v8.2.1.tar.gz tar zxvf node-v8.2.1.tar.gz cd node-v8.2.1 ./configure make && make install node -v v8.2.1 8) Install redis cd /opt wget http://download.redis.io/releases/redis-4.0.1.tar.gz tar zxvf redis-4.0.1.tar.gz cd redis-4.0.
Modify FS_HOSTNAME field in genieacs/config/config.json for device retrieve firmware file Original configuration: "FS_HOSTNAME" : "acs.example.com" New configuration example.: "FS_HOSTNAME" : "192.168.0.199" Note: It is the place where the device firmware file stored. Generally, it is the IP address on where your GenieACS server installed. Modify connect request username/password in genieacs/config/auth.
#!/bin/sh GENIE_PATH=/opt/genieacs/bin GENIE_GUI_PATH=/opt/genieacs-gui echo "start mongod." pidof mongod if [ $? != 0 ]; then /opt/mongodb-linux-i686-3.3.3/bin/mongod --dbpath /data/db --journal --storageEngine=mmapv1 --fork --syslog fi echo "start North Bound/RESTful Interface service." $GENIE_PATH/genieacs-nbi & echo "start ACS/CWMP service." $GENIE_PATH/genieacs-cwmp & echo "start HTTP/File streaming service." $GENIE_PATH/genieacs-fs & echo "start GenieACS/WebUI." cd $GENIE_GUI_PATH rails server -b 0.0.
2.1) Login Username and Password are admin/admin. 3) Device information Press Devices tab Move mouse to line end of your device, the Show link show up. Press Show link, the device information shows up. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
4) Access parameters Scroll up/down on Device parameters list, the Refresh and Edit link show up at line end of parameter. For Readable parameter For Readable and Writable parameter 4.1) Get parameter value Press on the Refresh link, the Pending tasks window will pop up on right top to ask you to allow or Cancel this action. Press Commit to get this parameter value. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Note: If the GenieACS can reach the device, the parameter value will be updated immediately. Otherwise, this request will be queued on Task queue list until next time device connect to GenieACS. Note: To update the whole tree, refresh the root parameter (InternetGatewayDevice.). Note: To update partial tree, refresh the parent node of the partial tree. 4.2) Set parameter value Press on the Edit link, editing window will pop up to ask you to change the value of this parameter. Input new value and press OK.
Press Commit to set this parameter value. Note: If the GenieACS can reach the device, the parameter value will be set immediately. Otherwise, this request will be queued on Task queue list until next time device connect to GenieACS. 5) Reboot device Press on Reboot link. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
The Pending tasks window will popġup to ask you to allow or Cancel this action. Press Commit to reboot device. Note: If the GenieACS can reach the device, the device will reboot immediately. Otherwise, this request will be queued on Task queue list until next time device connect to GenieACS. 6) Reset to default Similar to Reboot device except pressing on Factory reset link. 7) Firmware Upgrade 7.
Press File: browse button, select the firmware, and then press Upload button. The firmware will be added to listing files as below. 7.2) Upgrade Move mouse to the Push file>> link, the upgrade firmware name will pop up as below picture. Move mouse to the upgrade firmware name and press it. The Pending tasks window will pop up to ask you to allow or Cancel this action. Press Commit, then firmware upgrade started. Note: If the GenieACS can reach the device, the firmware upgrade will be started immediately.
Test Case Example VLAN Topology This VLAN Topology for 3-port LANs shows different PCs how to configure VLAN settings with different LAN ports and has two results for this configuration. (1) PC-A sends ICMP packet to PC-B IP (192.168.2.20) and captures traffic on PC-B. Thus, PCB will receive Tag20 traffic. (2) PC-B sends ICMP packet to PC-A IP (192.168.1.20) and captures traffic on PC-A. Thus, PCA will receive untag traffic. Note: z PC-A and PC-B are on Ubuntu OS.
Note: z Different PCs have different interface of network cards, like PC-A network card is eth1.10 for example 1 and PC-B network card is eth1.20 for example 2. z How to find out the terminal and the interface of network cards based on different PCs. From the following picture, you can click the finding your computer icon and input the terminal letters. Then, the interface will show the terminal icon and click to open it. Next, it shows the information when you click the terminal icon.
There are two examples to explain how configure VLAN settings. Example 1: PC-A pings PC-B (Access to Trunk) For PC-A, add default gateway and LAN's MAC to ARP. z Load VLAN and create VLAN interface, command as below: sudo modprobe 8021q sudo vconfig rem eth1.20 sudo vconfig add eth1.10 z Configure VLAN interface as below: sudo ifconfig eth1.10 192.168.1.20 netmask 255.255.255.0 up sudo ifconfig eth1 0.0.0.0 z sudo route add default gw 192.168.1.1 eth1.10 z sudo arp -s 192.168.1.
MQTT Topology This MQTT Topology shows the cellular router to connect PC-A and PC-B’s LANs and have two results are as below. Expect Result: (1) PC-A sends message to PC-B and PC-B should not receive any message. (2) PC-B sends message to PC-A and PC-A should receive message. Note: PC-A and PC-B should install MQTT Client software. There is a process to explain the steps and result. z Step1: Install mosquitto-clients on ubuntu or windows.
z Step2: Configure MQTT for the Cellular Router You need to add two users. For example, we create the users for test and test2. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
You need to add two ACLs based on the users you created. For instance, we create two ACLs for test user and test2 user. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Note: z For Receive message command format: Mosquitto_sub -h -t -u -P z For Send message command format: Mosquitto_pub -h -t -u -P -m 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
z Step3: There are two test MQTT examples. Example 1: PC-A sends message to PC-B and PC-B should not receive any message. For PC-B, command "mosquitto_sub -h 192.168.1.1 -t abc -u test2 -P test2". For PC-A, command "mosquitto_pub -h 192.168.1.1 -t abc -u test -P test -m test" and confirm the message on PC-B. It won’t receive any message on PC-B. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Example 2: PC-B sends message to PC-A and PC-A should receive message. For PC-A, command "mosquitto_sub -h 192.168.1.1 -t abc -u test -P test" For PC-B, command "mosquitto_pub -h 192.168.1.1 -t abc -u test2 -P test2 -m test" and confirm the message on PC-A. It will receive test message on PC-A. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
IP Routing Topology This IP Routing topology that the cellular router connects Router-1 and Router-2 will have two results. (1) PC-A sends ICMP packet to Router-1 LAN and WAN IP and they should have response. (2) PC-A sends ICMP packet to Router-2 LAN and WAN IP and they should have response. Note: Router-1 and Router-2 are pure routers and should be supported "NAT enable / disable". z LAN configuration: z WAN configuration: There are two examples to introduce how to work for routing.
Example 1: Add IP Routing on LAN interface z Step 1: The cellular router for Static Route configuration The Mode is on at the settings section and add the routing. z Step 2: Router-1 configuration is as below. (1) Login to the Router-1 web site, and then "NAT disable". (2) Configure LAN IP: 192.168.10.1 (3) Configure WAN IP: 192.168.1.50 z Result: PC-A sends ICMP packet to Router-1 LAN and WAN IP and they should have response. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
Example 2: Add IP Routing on WAN interface z Step1: The cellular router for Static Route configuration The Mode is on at the settings section and add the routing. z Step2: Router-2 configuration is as below. (1) Login to the Router-2 web site, and then "NAT disable". (2) Configure LAN IP: 192.168.20.1 (3) Configure WAN IP: 192.168.2.2 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
z Result: PC-A sends ICMP packet to Router-2 LAN and WAN IP and they should have response. 4G LTE COMPACT INDUSTRIAL CELLULAR ROUTER_M330/M330-W - UM V1.1.
20C
